BILLY GOAT LB352 LB Vacuum Cleaner Instruction Manual

LB352 LB Vacuum Cleaner
Instruction Manual

LB352
Beginning Serial #: 071621001

Accessories

HOSE KIT

(102mm x 3.05m) ,or vacuuming in hard Ilto-reach areas.
P/N 900460
HOSE CONNECTOR KIT

To connect two lengths of 4” hose (hose not included).
P/N 890045
STANDARD FELT DEBRIS BAGS

For use in dusty conditions.
P/N 900719
OPTIONAL TURF DEBRIS BAGS

For use in leaves and grass in non-dusty conditions.
P/N 900722

Original Instructions

IMPORTANT- READ CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE

SPECIFICATIONS

Sound in accordance with
2000/14/EEC standards| 97 dBa
Sound at operator’s ear| 77  dB.
Vibration at the operator position| 5g (5.17m/s)

SAFETY

WARNING

REPRODUCTION
This product can expose you to chemicals including gasoline engine exhaust, which is known to the State of California to cause cancer, and carbon monoxide, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

INSTRUCTION LABELS

The labels shown below were installed on your BILLY® GOAT LB Vacuum. If any labels are damaged or missing, replace them before operating this equipment. For your convenience in ordering replacement labels, part numbers are included in the Illustrated Parts List. The correct position for each label may be determined by referring to the  Figure and Item numbers shown.

ENGINE CONTROLS AND LABELS

BRIGGS & STRATTON

PACKING CHECKLIST

Your Billy Goat LB Vacuum is shipped from the factory in one carton, completely assembled except for the upper handle and debris bag.

READ all safety instructions before assembling the unit.
TAKE CAUTION when removing the unit from the box, the Handle Assembly is attached by cables and folded over.
PUT OIL IN THE ENGINE BEFORE STARTING

PARTS BAG & LITERATURE ASSY
Warranty card P/N- 400972, Owner’s Manual P/N-901015, General Safety and Warnings Manual P/N-100294, Declaration of Conformity P/N-900782, Literature LB  Accessories 900714.

Boxing Parts Checklist

• Debris Bag P/N-900718
• Literature Assy P/N-901016
• Briggs & Stratton 500 Series

ASSEMBLY

NOTE: Items in ( ) can be referenced in the Parts Illustration and Parts List on pages 8-9.
Your Billy Goat is shipped from the factory in one carton, completely assembled except for the upper handle and debris bag.

1. ROTATE the upper handle into the upward position and securely tighten the knobs. This machine can be stored with handle folded in the down position.
2. UNFOLD the debris bag (item 10) and fasten the bag neck onto the exhaust discharge opening.
3. ATTACH bag hanger straps to the loops (item 38), preassembled to the upper handle.
4. CONNECT spark plug wire.

OPERATION

VACUUMING OPERATION
VACUUM NOZZLE HEIGHT ADJUSTMENT: Nozzle height is raised and lowered by adjusting the front wheel height control.
FOR MAXIMUM PICKUP: Adjust the nozzle close to debris, but without blocking airflow into the nozzle. NOTE: Never bury the nozzle into debris.
CLEARING A CLOGGED NOZZLE & EXHAUST: Turn the engine off and wait for the impeller to stop completely and disconnect the spark plug wire. Wear durable gloves, and remove clogs. Danger, the clog may contain sharp materials. Reconnect the spark plug wire.

DEBRIS BAG
Debris bags are normal replaceable wear items.

NOTE: Frequently empty debris to prevent bag overloading with more weight than you can lift.

An optional bag and dust cover are available for use where debris will be vacuumed in dusty conditions (see “Accessories” on page 1). DO NOT place the bag on or near a hot surface,  such as the engine. Run engine at 1/2 throttle for first 1/2 hour to condition new bag. Your new bag requires a break-in period to condition the pores of the material against premature blockage. The entire bag surface serves as a filter and must be able to breathe for good vacuum performance. Be sure the engine has come to a complete stop before removing or emptying the bag.
This vacuum is designed for picking up trash, organic material, and other similar debris (see “Safety and General Operation” manual).
However, many vacuums are used where dust is mixed with trash. Your unit can intermittently vacuum in dusty areas. Dust is the greatest cause of lost vacuum performance.  Following these rules will help maintain your machine’s ability to vacuum in dusty conditions:

• Run the machine at idle to quarter throttle.

• The debris bag must be cleaned more frequently. A vacuum with a clean, pillow-soft bag will have good pickup performance.
  One with a dirty, tight bag will have poor pickup performance. If dirty, empty the debris and vigorously shake bag free of dust.

• Machine or pressure-wash debris bag if normal cleaning does not fully clean the bag. The bag should be thoroughly dry before use.
  Having one or more spare debris bags is a good way to reduce downtime while dirty bags are being cleaned.

DO NOT leave debris in the bag while in storage

COMPOST
Vacuumed leaves, grass, and other organic material from your own yard can be emptied into a pile or composter to provide enriched soil for later use as fertilizer in gardens and flower beds. NOTE: Allow green chips to dry before spreading them around living plants.

MAINTENANCE

NOTE: Items in ( ) can be referenced in the Parts Illustration and Parts List on pages 8-9.

PERIODIC MAINTENANCE

Periodic maintenance should be performed at the following intervals:

IMPELLER REMOVAL

1. Wait for the engine to cool and disconnect the spark plug.
2. Drain fuel and oil from the engine.
3. Remove the bag and remove the upper handle.
4. Invert and support the machine without placing the weight of the machine on the engine’s recoil starter.
5. Remove rear wheels (item 11), and bolt axle bracket (item 48), one on each side, closest to the middle inlet plate (item 3), washer (item 57), and nut (item 49).
6. Remove the intake wrapper assembly (item 2) and middle inlet plate (item 3), eight screws, and eight nuts.
7. Remove the impeller bolt (item 37) and lock the washer (item 36).
8. Lift the impeller free of the engine.
9. If the impeller does not remove easily, obtain a 1″ (25.4mm) longer bolt of the same diameter and thread type as the impeller bolt. Thread longer bolt by hand into crankshaft until bolt bottoms. Using a suitable gear or wheel puller against the bolt head and impeller back-plate (near the blades), remove the impeller from the shaft.
10. Reinstall the new impeller, impeller bolt, and lock washer in reverse order. Torque impeller bolt to 33-38 ft-lbs (45-52 N.m).

TROUBLESHOOTING

Check the impeller and replace it if required. Check engine.
Will not vacuum “or h\atscaoi/
vacuum performance| Dirty debris bag. Nozzle height set too high or low. The Hose kit cap missing. Clogged nozzle or exhaust. An excessive quantity of debris.| Clean debris bag. Shake the bag clean or wash it. Adjust nozzle height. Check for the hose kit cap. Unclog the nozzle or exhaust. Allow air to feed with debris.
Erigine4fil not start| Throttle in off position. Out of gasoline. Bad or old gasoline. The spark plug wire was disconnected. Dirty air cleaner.| Check throttle. Connect spark plug wire. Clean or replace the air filter. Or contact a qualified service person.
The engine is locked, but will not.
Pullover| Debris locked in the impeller. Engine problem.| See page 6. Contact an engine service dealer for engine problems.
Nozzle scrapes ground in the lowest height setting| Nozzle height out of adjustment.| Adjust nozzle height (See “NOZZLE HEIGHT ADJUSTMENT” for hard surfaces on page 6.)

LB PARTS DRAWING

LB PARTS LIST

EC Declaration of Conformity
Category

This is to certify that the products listed in this document meet the requirements of the European Community Law, and can carry the CE mark.

Directive:

  Directive:| Guaranteed Sound
Power Level| Measured Sound Power Level| Sound Pressure Level at Operator’s Ear (1)| Engine Net Power
REPRODUCTION| Hand/Arm Vibration (2)| Mass
---|---|---|---|---|---|---
LB352| 98 dB(A)| 97 dB(A)| 77 dB(A)| 2.6 kW| 5.17 m/s2| 25.85 kg

Manufacturing Place / Keeper of Documentation

1803 S.W. Jefferson
Lees Summit, MO 640630308 USA| Jeroen Engelen Schepersweg 4a 6049CV
Herten, NL|
---|---|---
10/05/2015| Ted Melin
Engineering Manager

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>