MOUNTAIN LAB Gear Scout 2w 2 Way Radio User Manual

MOUNTAIN LAB Gear Scout 2w 2 Way Radio

KEY FUNCTIONS

1. Push-To-Talk (PTT)
2. Power/Call Tone
3. Lamp/Weather
4. Signal Light Button
5. LED Light
6. Signal Light
7. Speaker
8. Microphone
9. Monitor/Scan
10. Lock/Menu
11. Accessory Port Speaker Microphone

DISPLAY SCREEN GUIDE

GETTING STARTED

Install the AA NiMH Rechargeable Batteries

1. Remove the belt clip by inserting a finger under the tab at the top and sliding the belt clip up.
2.  Remove the two screws on the back of the radio by turning them counter-clockwise to open the cover.
3. Install the included AA NiMH batteries according to the orientation shown in the battery compartment.
4. Close the battery compartment cover and replace the screws, turning clockwise until snug.

Battery Life
A fully charged battery is indicated by three solid bars . When the battery is low, the display will show one blinking bar and the radio will emit a low battery warning beep after each transmission.

Note

• Remove the batteries from the radio prior to storage. Batteries left in the radio during storage may corrode over time and may cause permanent damage to your radio.
• Do not mix old and new or alkaline and NiMH batteries.
• Charge the supplied NiMH batteries once every three months when not in use.

Using the Charging Dock
The Micro-USB charging dock allows you to conveniently charge the NiMH battery of your SCOUT radio in the dedicated dock, using the included certified charging adaptor (5V, ≥1A).
Note: Do not attempt to charge alkaline batteries.

How To Charge the Battery

1. Ensure that your radio is turned OFF.
2. Plug the Micro-USB cable into the Micro-USB port on the charging dock. Insert the USB connector into the charging adapter. Plug the charging adapter into a household electrical outlet.
3. Place the radio into the charging dock. The battery meter on the display will cycle to indicate the battery is charging. The battery is fully charged when the display shows three solid bars.

BASIC OPERATION

Turning the Radio On and Off

1. Press and hold the power button, to turn your radio on/off.
2. The display will show the current channel, sub-code and enabled features.

Setting the Volume

1. Press   to increase the volume (maximum volume is 7).
   Press    to decrease the volume (minimum volume is 1).

2.  When volume level 0 is selected, the radio is muted and is displayed

Setting the Channel

1. Press the  button. The channel number will start to flash.
2. Press  or   to change the channel number.
3. Press the PTT button to select the channel and exit the menu, or press again to proceed to the sub-code selection menu.

Channels and Frequencies

Setting the Sub-Code

1. Press the to flash. button until the sub-code number starts
2. Press or to change the sub-code number.
3. Press the PTT button to exit the menu.

Note: When sub-code “0” is selected, the radio can receive transmissions from any radio on the same channel, regardless of sub-code. However, only those radios also on sub-code “0” will be able to receive its transmissions.

Transmitting and Receiving
To talk, press and hold the PTT button. When transmitting, the icon is shown. Release the PTT button when you are finished talking. Do not use the radios closer than two meters apart or the radios may experience feedback.
When receiving a transmission, the icon will be displayed.

Note: With all radios, it is good practice to hold the PTT button for a half second longer before and after speaking to ensure your transmission is not cut off.

PTT Timeout Timer
If the PTT button is held for longer than 60 seconds, radio will stop transmitting.
This is to prevent accidental transmission.

KEYPAD FEATURES

Call Tone

1. To transmit a call tone, press the button.
   Setting the Call Tone

2. To select the call tone to be used, press the button until the call tone menu “CA” appears. The flashing number indicates the current call tone.

3. Press or or to change the call tone.

4. Press the PTT button to exit the menu.

Note : Call tone “0” mutes the call tone feature. No call tone will be sent, but they can still be received.

Keypad Lock
The keypad lock feature prevents accidental keypad button activation. This is especially useful when the radio is used with the included speaker microphone accessory and placed inside a backpack or otherwise secured.

1. To lock the keypad buttons, press and hold the button until the lock indicator is displayed.
2. Repeat the procedure to unlock the keypad.

Scan
The scan function allows the user to listen for any activity on any channel and its matched sub-code (as is selected in the main menu).

1. Press the button to start scanning. The “SCAN” icon will show and the display will cycle through the channels and sub-codes being scanned for activity.
2. When activity is detected, the radio will stop scanning and receive the transmission. At the end of transmission, press the PTT button within five seconds to respond. Otherwise the radio will resume scanning.
3. If the PTT button is pressed while the device is scanning, the transmission will be sent on the main selected channel.
4. Press the button to exit scan mode.

Note : If the device stops on an unintended/undesired transmission, press or to resume scan OR temporarily remove that channel from the scan list by pressing and holding or for three seconds.
To restore removed channels to the scan list, press to exit and re-enter scan mode.

Monitor
Monitor mode can be used to listen for weak signals or to check activity on the current channel.

1. Press and hold for three seconds to enter monitor mode.
2. Release the button to exit monitor mode.

LED Lamp

Press the button to turn on/off the lamp. The lamp feature is disabled by the keypad lock.

Weather
In weather mode, your radio can receive NOAA weather information, warnings and alerts.

Press and hold the button for three seconds to enter or exit weather mode.

Weather Channel
Setting the Weather Channel

1. In weather mode, press the button until the weather channel number flashes.
2. Press or to select the appropriate channel for your area.
3. Press the PTT button to set the channel and exit the menu.

Setting the Weather Alert
You radio can be set to respond to NOAA Weather Radio emergency messages.

1. In weather mode, press the button twice. The   icon will be displayed.
2. Press or  to turn weather alert on or off.
3. Press the PTT button or to exit the weather alert menu.
4.  Repeat the step to disable the weather alert.

WEATHER CHANNELS & FREQUENCIES

Signal Light (SOS)
The signal light button can be used to emit an emergency call tone and SOS flashing light. This feature should only be used in a real emergency to increase visibility.
Note : This device does not have the capability to contact emergency services or provide any location information, and should not be confused with a dedicated personal locator device that is designed to do so.

1. Press and hold the SOS button for three seconds. The red LED light will begin to flash the SOS signal light and an emergency tone will be transmitted.
2. To cancel the emergency signal light, press the SOS button once more.

MENU FEATURES
Voice-Operated Transmission (VOX)
Voice-operated transmission allows the user to send transmissions without pressing the PTT button. The radio will detect an increase in sound levels and transmit automatically.

1. To activate VOX, press the   button until “VOX” appears on the display, along with a flashing number (0-3).
2. Press or  to change the VOX sensitivity level (1-3) or turn off (0).
   • 0 = VOX function off
   • 1 = Low sensitivity
   • 2 = Medium sensitivity
   • 3 = High sensitivity
3. Press the PTT button to exit the menu.

Note: The PTT button can still be used to send transmissions in VOX mode.

Dual Channel Monitor (2CH)
Dual channel monitor allows the user to listen for transmissions on two channels at the same time—the main channel and sub-code as set on in the main menu, and a second channel and sub-code.

1. Press the button until the dual channel monitor menu “2CH” appears. The flashing number indicates the current secondary channel to be monitored (1-22), and “OF” indicates that the feature is turned off.

2. Press or to select which secondary channel to monitor.
   Note : There is no option to select a sub-code in the dual channel monitor menu. The sub-code is dictated by the sub-code that is selected for that channel in the main sub-code menu setting. For example: If the main channel setting for channel 5 is set to
   sub-code 121, then that will be the sub-code used for the channel 5 dual channel monitor selection.

3. Press the PTT button to exit the menu.
   In dual channel monitor mode, the display will alternate between the main channel (and sub-code) setting and the dual channel secondary channel.

In the case that a transmission is received on the secondary dual channel monitor channel, any transmissions made within 10 seconds of receiving will be occur on the secondary channel. Otherwise, all transmissions will be made on the main channel and sub-code setting.

Setting High and Low Transmission Power

1. Press the button until the power selection menu “Pr” appears.

2. Press or  to select the flashing “HI” or “LO” power.
   Note: High power (2 watts) is only available on channels 1-7 and 15-22. Channels 8-14 are restricted to Low power (0.5 watts) only, in accordance with governmental regulation.

3. Press the PTT button to exit the menu. High power is indicated on the main display (indicated by “HI”) when channels 1-7 or 15-22 are selected.

Note : The power setting does not affect the ability of the radio to receive transmissions. Only the output power is affected by this setting.

ADDITIONAL FEATURES

• Keypad Tone On/Off
  Press and hold the button while turning the radio on to turn the keypad tone off or back on.

• Roger Tone On/Off
  Press and hold the button while turning the radio on to turn the roger beep (PTT transmit beep) off or back on.

• Automatic Power Saving
  This feature turns off the display automatically when not in use to save battery life.

• Water Activated LED
  If the radio is dropped in water, a flashing white LED light will be activated automatically to assist in finding the dropped radio in darkness. After retrieving the radio, press any button to deactivate the flashing light.

RADIO FREQUENCIES

Code No| Frequency (Hz)| Code No| Frequency (Hz)| Code No| Frequency (Hz)| Code No| Frequency (Hz)
---|---|---|---|---|---|---|---
1| 67| 11| 97.4| 21| 136.5| 31| 192.8
2| 71.9| 12| 100| 22| 141.3| 32| 203.5
3| 74.4| 13| 103.5| 23| 146.2| 33| 210.7
4| 77| 14| 107.2| 24| 151.4| 34| 218.1
5| 79.7| 15| 110.9| 25| 156.7| 35| 225.7
6| 82.5| 16| 114.8| 26| 162.2| 36| 233.6
7| 85.4| 17| 118.8| 27| 167.9| 37| 241.8
8| 88.5| 18| 123| 28| 173.8| 38| 250.3
9| 91.5| 19| 127.3| 29| 179.9| |
10| 94.8| 20| 131.8| 30| 186.2| |

CTCSS 38

CDCSS 83

SAFETY AND GENERAL INFORMATION

FCC Warning
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Safety Information for Radios
Your wireless handheld portable transceiver contains a low power transmitter. When the talk button is pushed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty factor not to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for handheld wireless devices.

Important
FCC RF Exposure Requirements: For body-worn operation, this radio has been tested and meets the FCC RF exposure guidelines when used with accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Use only the supplied antenna. Unauthorized antennas, modifications or attachments could damage the transmitter and may violate FCC regulations.

Normal Position
Hold the transmitter approximately 25 mm from your face and speak in a normal voice, with the antenna pointed up and away.

Warnings
Product safety and RF Exposure for two way radio:

Before using this two way radio, please read the manual which contains important operating instructions for safe usage, RF Energy Awareness, control information and operational instructions for compliance with RF Energy Exposure limits in applicable national and international standards, and also read the operational instructions for safe use.

C AU T ION

Test position and configuration Head SAR was performed with the device configured in the positions according to IEEE1528, and face up SAR was performed with the device 25 mm from the phantom. Body SAR was performed with the belt clip on the device 0 mm from the phantom. Body SAR was also performed with the headset attached and without.

Antennas

1. The antenna is unique to this product. Please do not attempt to alter or replace.
2. For safe operation, the antenna for the product shall be least 25 mm away from your face when speaking.
3. Attempting to alter or replace the antenna will affect performance and void the warranty.
4. DO NOT use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.

Batteries
All batteries can cause property damage and/or bodily injury such as burns if a conductive material touches exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become hot.

• Exercise care when removing NiMH or AA batteries. Do not use sharp or conductive tools to remove these batteries.
•  Exercise care in handling any charged battery, particularly when placing it inside a pocket or enclosed container with metal objects.
• Do not discard your battery in a fire.
•  Do not replace the battery in any area labeled “Hazardous Atmosphere”. Any sparks created in a potentially explosive atmosphere can cause explosion or fire.
•  Do not disassemble, crush, puncture, shred or otherwise attempt to change the form of your battery.
•  Do not dry a wet battery or damp battery with an appliance or heat source, such as a hair dryer or microwave oven.
•  If the radio battery contact area has been submerged in water, dry and clean the battery contacts before attaching the battery to the radio.
• Do not attempt to charge alkaline batteries.

CAUTION
Battery Charger Safety Instructions

1. Turn the radio off when charging the battery.

2. Do not expose the charger to outside environment. Chargers should only be used indoors.

3. Do not operate or disassemble the charger. Do not use a charger that has been dropped or damaged in any way.

4.  Never alter the AC cord or plug provided with the unit. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. An improper condition can result in a risk of electric shock.

5. To reduce the risk of damage to the cord or plug, pull the plug rather than the cord when disconnecting the charger from the AC receptacle.

6. To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance or cleaning.

7. Use of an attachment not recommended or sold by Mountain Lab Gear may result in a risk of fire, electric shock or personal injury.

8. Make sure the cord is located so it will not be stepped on, tripped over or subjected to damage or stress.

9. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of a fire and/or electric shock. If an extension cord must be used, make
   sure that

   • The pins on the plug of the extension cord are the same number, size and shape as those on the plug of the charger.
   •  The extension cord is properly wired and in good condition.

10. The supply cord of the AC adaptor cannot be replaced. If the cord is damaged, call customer service.

The information listed below provides the user with the information needed to make him or her aware of RF exposure, and what to do
to assure that this radio operates with the FCC RF exposure limits of this radio.

Electromagnetic Interference/Compatibility
Note : Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility.

During transmissions, this radio generates RF energy that can possibly cause interference with other devices or systems.

Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy.

Aircraft
When instructed to do so, turn off your radio when onboard an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions.

Medical Devices – Pacemakers, Defibrillators or other Implanted Medical Devices Persons with pacemakers, implantable cardioverter defibrillators (ICDs) or other active implantable medical devices (AIMD) should:

• Consult with their physicians regarding the potential risk of interference from radio frequency transmitters, such as portable radios (poorly shielded medical devices may be more susceptible to interference).

• Turn the radio OFF immediately if there is any reason to suspect that interference is taking place.

• Do not carry the radio in a chest pocket or near the implantation site, and carry or use the radio on the opposite side of their body from the implantable device to minimize the potential for interference.

  • Hearing Aids
    Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.

  • Other Medical Devices
    If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information.

  • Use of Communication Devices While Driving
    Always check the laws and regulations on the use of radios in the areas where you drive.

• Give full attention to driving and to the road.

• Use hands-free operation, if available.

Pull off the road and park before making or answering a call, if driving conditions or regulations so require.

For Vehicle with Air Bags
Refer to the vehicle manufacturer’s manual prior to installation of electronic equipment to avoid interference with air bag wiring. Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle.

Potentially Explosive Atmosphere
Turn off your radio prior to entering any area with a potentially explosive atmosphere. Only radio types that are especially qualified should be used in such areas as “Intrinsically Safe”. Do not remove, install or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death.

Note : The areas with potentially explosive atmosphere referred to above include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles (such as grain, dust or metal powders) and any other area where you would normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are often—but not always—posted.

Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted “turn off two-way radios”. Obey all signs and instructions.

Warning: CHOKING HAZARD – Small parts. Not for children under 3 years.

For warranty inquiries, please contact: warranty@mountainlabgear.com

References

• World Health Organization (WHO)
• FCC OET Authorization Search
• Site officiel de l'Organisation mondiale de la Santé

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>