AMERICH Airbath Air Tub User Guide

AMERICH Airbath Air Tub

Product Information

The product is a whirlpool system that comes in two different series: Luxury Series and Builder Series. The Luxury Series has a blower and offers additional features like chromotherapy, wave mode, and automatic purge. The Builder Series has a pump and comes with an optional built-in water level sensor.

Product Usage Instructions

Luxury Series
Always use dedicated outlets for each power supply. To turn on the blower, press the On/Off button once. The blower will start at 50% speed. Press the button again to turn off the blower. While the blower is on, you can adjust the speed by pressing and holding the System Speed button. Release the button once you reach the desired speed. You can also change the wave mode by pressing the Wave Mode button. Press once for Wave mode, twice for Pulse mode, and three times to return to maximum speed. If the water level falls below the water level sensor while the blower is on, an automatic purge will initiate in thirty minutes to dry the air channels. After the purge cycle, the blower will turn off. For chromotherapy, press the Chromotherapy button once to turn on auxiliary equipment and set it to white light. Press again for a slow rainbow cycle, again for a fast rainbow cycle, and again to cycle through Turquoise, Blue, Magenta, Red, Orange, Yellow, Green. Press and hold for one second to turn off auxiliary equipment.
Note : The blower hose is shipped loose and needs to be attached to the blower and check valve before use. Tighten clamp around each end.

Builder Series
Always use dedicated outlets for each power supply. Fill the tub until the highest jet is covered by at least 2 inches of water. Do not run the pump without water in the tub. If the optional built-in water level sensor is installed, fill the tub until the water level sensor pad is covered. Press the On/Off button once to start the
pump and again to turn it off. The control box has a 10-minute timer that will turn off the unit automatically. To continue your bath, simply push the button to repeat the cycle.
Note : If water falls below the water level sensor while the pump is on, the system will turn off. The control box has a 20-minute timer that will turn off the unit automatically.

INSTALLER: To be removed for use by the occupant

operating instructions

AIRBATH®

Water Level Sensor
If water falls below water level sensor while blower is on, an automatic purge will initiate in thirty minutes to dry the air channels.
Automatic Purge
Thirty minutes after the water falls below the water level sensor the blower will start again for a one-minute purge cycle allowing piping to thoroughly dry

AIRBATH® + LIGHT On/Off Key

• 1st Press: The blower starts at 50%.

• 2nd Press: The blower stops.
  While the blower functions press and hold

• 3 sec.: Wave – Speed will vary gradually from maximum to minimum

• 6 sec.: Pulse – Speed will go directly to minimum and then straight back to maximum.

System Speed

• 1st Press: Press and hold to increase the pump speed, release pressure at the desired speed.
• 2nd Press: Press and hold to decrease the pump speed, release pressure of the desired speed.

Chromotherapy

• 1st Press: Auxiliary equipment ON > White
• 2nd Press: Slow rainbow cycle
• 3rd Press: Fast rainbow cycle
• 4th Press: Turquoise, Blue, Magenta, Red, Orange, Yellow, Green Return to slow rainbow cycle
• Press and Hold 1 sec.: Auxiliary equipment OFF

Automatic Purge
(only available with models equipped with Airbath® )
Thirty minutes after the water falls below the water level sensor the blower will start again for a one-minute purge cycle allowing piping to thoroughly dry

Note: Blower hose for AirBath Systems is shipped loose:

1. Remove red caps from blower and check valve.
2. Attached grey hose to blower and check valve.
3. Tighten clamp around each end.

BUILDER SERIES
The Builder Series whirlpool is equipped with an On/Off Button (fill tub until the highest jet is covered by at least 2” of water. Do not run pump without water in the tub.)

1. Press the Button to start the pump.
2. Press a second time to stop the pump. The Control Box is manufactured with a 10 minute timer that will turn off the unit automatically. To continue your bath, simply push the Button to repeat the cycle.

Note: If OPTIONAL built in water level sensor is installed on your tub, fill the tub with water until the water level sensor pad is covered. Now you can press the Button to start the pump.

LUXURY SERIES

1. Press the Button to start the pump.
2. Press a second time to stop the pump. The Control Box is manufactured with a 20 minute timer that will turn off the unit automatically. To continue your bath, simply push the Button to repeat the cycle.

Water Level Sensor
If water falls below water level sensor while pump is on, the system will turn OFF.

PLATINUM SERIES OR LUXURY SERIES + LIGHT

Chromotherapy

• 1st Press: Auxiliary equipment ON > White
• 2nd Press: Slow rainbow cycle
• 3rd Press: Fast rainbow cycle
• 4th Press: Turquoise, Blue, Magenta, Red, Orange, Yellow, Green Return to slow rainbow cycle
• Press and Hold 1 sec.: Auxiliary equipment OFF

Water Level Sensor
If water falls below water level sensor while blower is on, the system will turn OFF.

COMBO SERIES + LIGHT

• Blower On/Off
  1st Press: The blower starts at 50%
  2nd Press: The blower stops.

• Blower System Speed
  1st Press: Press and hold to increase the blower speed, release pressure at the desired speed.
  2nd Press: Press and hold to decrease the blower speed, release pressure at the desired speed.

• Blower Wave Mode
  1st Press: Wave – Speed will vary gradually from maximum to minimum.
  2nd Press: Pulse – Speed will go directly to minimum and then straight back to maximum.
  3rd Press: Returns to maximum speed.

Pump On/Off Chromotherapy

• 1st Press: Auxiliary equipment ON > White
• 2nd Press: Slow rainbow cycle
• 3rd Press: Fast rainbow cycle
• 4th Press: Turquoise, Blue, Magenta, Red, Orange, Yellow, Green Return to slow rainbow cycle
• Press and Hold 1 sec.: Auxiliary equipment OFF

Water Level Sensor
The system will turn OFF if the water level falls below the water level sensor while pump is on.
If water falls below water level sensor while blower is on, an automatic purge will initiate in thirty minutes to dry the air channels.

Automatic Purge
Thirty minutes after the water falls below the water level sensor the blower will start again for a one-minute purge cycle allowing piping to thoroughly dry.

Each system will automatically stop after 20 minutes.
**Note: Blower hose for AirBath Systems is shipped loose:

1. Remove red caps from blower and check valve.
2. Attached grey hose to blower and check valve.
3. Tighten clamp around each end.

IMPORTANT: Keep these instructions with the Americh Installation Instructions. These operating instructions are for units with systems. All installation, warnings, warranties, and other such information can be found in the Americh Installation Instructions. Go to www.americh.com for additional copies.
Manufacturer recommends the use of Jet Fresh® or a similar system cleaning solution to maintain your whirlpool or Airbath® System
Always check www.americh.com for the most updated installation instructions

in compliance with
ANSI Z124.1 – 1995 ANSI A112.19.7 – 1987
ANSI A112.19.8 – 1987
City of Los Angeles M980036 and M820132

References

• Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>