UPIKER UP2210TOW12335 Single Elongated Toilet Installation Guide

UPIKER UP2210TOW12335 Single Elongated Toilet

One-Piece Toilet Features

TOOLS AND MATERIALS REQUIRED

A. Water Supply Kit ( Not needed if replacing existing toilet)

B. Adjustable Wrench

C. Flathead Screwdriver

D. Level

E. Nut Driver or Socket Set

F. Putty Knife

G. Tape Measure

Handling

Toilets can be heavy! Please handle carefully – it may be a two-person job. If you have a one-piece toilet, support the bowl with one arm and the tank with the other. If you have a two-piece toilet, move the parts separately to avoid damaging them.

Removing Your Old Toilet

1. Turn off the water supply.
2. Flush the toilet to empty the tank, remove any water left in tank or bowl.
3. Disconnect the supply line from the tank.
4. Make sure the water supply valve is shut off before installation.
5. Remove decorative caps. Unscrew nuts that attach the toilet to the floor.
6. Remove toilet.
7. Remove old closet bolts from closet flange. Clean any old wax, putty, etc from base area.

Important Note Regarding Water Supply:

Before installation, please ensure that the shut off valve is greater than 7.5″ from the center of the drain to the center of the shut off valve one either side.

Note:

This is a true 12″ rough-in toilet from finished wall to center of the drain (no less than 12″). Baseboard thickness may reduce the rough-in dimension.

One Piece Toilet Installation Procedure

Step 1. Install new floor bolts to the floor flange.

Step 2. Attach flexible water supply line to the inlet of the fill valve and hand tighten only. At this point, DO NOT connect to the water shut-off valve.

Step 3. Place a new wax ring around the water flange of the toilet bowl.

Step 4. Lower the toilet onto the closet bolts, so the bolts project through mounting holes in base of toilet. Using a rocking motion, press the bowl down to position the toilet onto the flange.

Step 5. Install plastic cap washers, followed by metal washers and nuts onto the closet bolts. Tighten the bolts alternately until toilet is firmly seated on the floor. CAUTION: DO NOT OVERTIGHTEN NUTS, SEVERE DAMAGE MAY OCCURE

Step 6. Install the plastic cap covers.

Step 7. Connect the flexible water supply line (not included) to the shut off valve. Tighten coupling nuts securely.

Connect Water Supply

1. Connect water supply line (new or existing) between shut off valve and tank inlet water fitting. Tighten coupling nuts securely. NOTE: DO NOT OVERTIGHEN
2. Turn on supply valve and allow tank to fill until float rises to shut off position.
3. Check for leakage at fittings, tighten or correct as needed.

CARE AND MAINTAINANCE

DO NOT

1. Do not stand on the toilet cover, and do not place heavy objects on it. (Or else it may cause crack)
2. Do not clean the toilet seat with household cleaners, volatile, thinner and eradicator, or use nylon brush, and avoid cholorine-containing, corrosive and abrasive cleaners. Maintain the shiny surface by using soft fabric and clean water. (Or else it may cause abrasion or crack)
3. Do not let child play the toilet cover, to avoid hurting fingers and other accident.

DO

1. Clean or wash it with neuter cleaners ( such as soap powder). And then dry it with clean fabric.
2. Open and close toilet seat cover tenderly. Toilet seat and cover both have the function of slow closing.
3. Wipe outside of the toilet gently with a damp cloth and blot dry with a soft towel. Make sure that the complete surface is cleaned and completely dry.
   NOTE: IMPROPER CARE MAY CAUSE THE WARRANTY TO BECOME INVALID.

Contact

Email: cross@nefelthomeinc.com TEL: 303-7312759

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>