UPIKER UP2208TOW12003 GPF Dual Flush skirted Toilet Instruction Manual

UPIKER UP2208TOW12003 GPF Dual Flush skirted Toilet

PRIOR TO INSTALLATION

• Inspect the toilet to ensure no damages have occurred while in shipping.
• Observe all plumbing and building codes in accordance with your state and local requirements.
• All dimensions are nominal! Be sure to measure your toilet prior to installation.
• The step-by-step guidelines in the installation instructions are a general reference. Should there be any discrepancies, UPIKER cannot be held liable. It is recommended to install all UPIKER products by hiring a licensed professional.
• Read installation and maintenance instructions thoroughly before installing. Be sure to use proper tools and always wear proper personal safety accessories for your protection.
• Two people are recommended to handle and install this product as it is fragile.

If you have any questions or concerns please contact us: at cross@nefelthomeinc.com.

SUGGESTED TOOLS & MATERIALS

INCLUDED PARTS

ONE-PIECE TOILET

1. Turn Off Water Supply
   • Close the toilet supply valve and flush the tank completely, and use a towel to remove excess water.
   • Disconnect and remove the supply line, if you are replacing the valve shut the main water supply first.
   • Remove closet bolts from the flange and clean wax and putty from the base area.
2. Rough-In the Toilet
   • Measure the wall from behind the toilet to the middle of the closet bolt. Your rough-in measurement should be 12”.
3. Install Closet Bolts
   • Install closet bolts to flange channel, turn 90° and slide into place 6” (152mm) apart and parallel to the wall.
4. Install Wax Seal
   • Invert the toilet on the floor (use a cushion to prevent damage), and install a wax ring evenly around the waste flange with the tapered end of the ring facing the toilet. Apply a thin bead of sealant around the toilet base.
5. Position Toilet on Flange
   • Hand-tighten the water supply hose to the fill valve in the back of the toilet. Do not connect to the water supply yet.
   • Unplug the floor waste opening and install a toilet on the closet flange so bolts project through the mounting holes.
   • Loosely install retainer washers and nuts.
6. Install Toilet
   • Position toilet square to the wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until the toilet is firmly sealed to the floor. Do not over-tighten nuts, it might crack ceramic.
   • Smooth off the bead of sealant around the base. Remove excess sealant.
   • Place cover caps to hide installation holes on the toilet.
   • Connect the water supply to shut off the valve, and check for leaks. Tighten if necessary.

TOILET SEAT INSTALLATION

1. Disassemble
   • Disassemble the cover cap and the hinge.
2. Construct Hinges
   • Insert screw and nut into the hole on the hinge.
   • Attach blind hole screw fixing to the bottom of the screw.
3. Attach Hinges
   • Insert hinges with blind hole screw fixings attached into holes on the toilet bowl.
   • Lightly tighten hinges with a screwdriver to allow for later adjustment.
4. Adjust and Cover Hinges
   • Be sure the hinge is all the way forward for a proper seat fitting.
   • Place the covers onto the hinges.
5. Adjust and Attach Seat
   • Align the seat to the hinges then firmly tighten the hinges.
   • Attach the seat to the secure hinges.
   • Adjust the seat to align with the bowl.

TOILET SEAT USAGE

• To remove, push the middle button until you hear a “click”, then pull straight up.
• To re-install, align hinge posts with reference marks on the seat, then push down until you hear a “click”.

One Button:

Two Button:

Documents / Resources

| UPIKER UP2208TOW12003 GPF Dual Flush skirted Toilet [pdf] Instruction Manual
UP2208TOW12003, GPF Dual Flush skirted Toilet, UP2208TOW12003 GPF Dual Flush skirted Toilet, Flush skirted Toilet, skirted Toilet, Toilet
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>