Buff HUB Wireless Remote User Guide
- June 6, 2024
- Buff
Table of Contents
- Buff HUB Wireless Remote User Guide
- ATTACHING THE HUB TO YOUR CAMERA
- CHARGING THE HUB
- WHAT’S INCLUDED
- POWERING THE HUB ON / OFF
- SENDING A TEST FIRE
- SETTING THE FREQUENCY
- ADJUSTING THE DISPLAY BRIGHTNESS
- BLUETOOTH
- TTL MODE
- HSS MODE
- ABOUT
- FCC ID: OUEPCBHUB
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Buff HUB Wireless Remote User Guide
ATTACHING THE HUB TO YOUR CAMERA
Slide the bottom of the HUB onto your camera’s hot shoe.
Turn the locking wheel clockwise to lock the HUB on to your camera.
CHARGING THE HUB
To charge the HUB plug the USB-C side of the included charging cable directly into the HUB. Then plug the USB-A side into a wall outlet connector.
WHAT’S INCLUDED
(1) HUB Wireless Remote
(1) USB-A to USB-C Charging Cable
(1) Rechargeable Internal Lithium-ion Battery
2-Year Factory Warranty
- CHARGING PORT
- SYNC JACK
- ROTARY WHEEL
- TOP HOT SHOE
- POWER BUTTON
- REAR DISPLAY
- LOCKING BOTTOM HOT SHOE (CAMERA BRAND SPECIFIC)
POWERING THE HUB ON / OFF
Press and hold the POWER button, located on the right side of the HUB, for two seconds.
SENDING A TEST FIRE
8. FREQUENCY
9. TTL/MAN and HSS
10. BATTERY INDICATOR
11. BLUETOOTH
SETTING THE FREQUENCY
The FREQUENCY ranges from 1 – 16. To set the frequency turn the ROTARY WHEEL
until FREQUENCY appears on the display.
Press in on the ROTARY WHEEL to enter the FREQUENCY section. Turn the ROTARY
WHEEL until your desired frequency appears. Press in on the ROTARY WHEEL to
confirm your selection.
ADJUSTING THE DISPLAY BRIGHTNESS
To adjust the display brightness turn the ROTARY WHEEL until BRIGHTNESS
appears on the display. Press in on the ROTARY WHEEL to enter the BRIGHTNESS
section.
Turn the ROTARY WHEEL until your desired brightness appears.
BLUETOOTH
By default, BLUETOOTH is ON when the HUB is first activated. To turn BLUETOOTH
ON or OFF, turn the ROTARY WHEEL until BLUETOOTH appears on the display. Press
in on the ROTARY WHEEL
to enter the BLUETOOTH section. Turn the ROTARY WHEEL to toggle between ON and
OFF. Press in on the ROTARY WHEEL to confirm your selection.
TTL MODE
To set the HUB into TTL mode, turn the ROTARY WHEEL until TTL appears on the display. Press in on the ROTARY WHEEL to enter the TTL section. Turn the ROTARY WHEEL to toggle between TTL and MAN (for manual). Press in on the ROTARY WHEEL to confirm your selection.
HSS MODE
The HUB will enter HSS mode automatically when your camera is set above it’s max sync speed.The HUB will also superseed any settings found on the LINK. For example, if the LINK is set to COLOR MODE but you are now shooting above your camera’s max sync speed, the HUB will then adjust the LINK and place it into HSS MODE.
ABOUT
To access the serial number, current firmware version, and FCC ID within the HUB interface, first turn on the HUB and use the rotary dial to scroll to the ‘ABOUT’ section. Then, once ‘ABOUT’ appears on the display, press in on the rotary dial to enter the section. Finally, scroll using the rotary dial to view each item.
FCC ID: OUEPCBHUB
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>