DYCONN DF-007T Bidet Auto Toilet User Manual

DYCONN DF-007T Bidet Auto Toilet

IMPORTANT SAFEGUARDS

When using electrical products, especially when children are present, basic safety precautions shouldalways be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING

WARNING -To reduce the risk of burns, electrocution, fire, or injury to persons.

1. Close supervision is necessary when this product is used by, on, or near children or i nvalids.
2. Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
3. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never block the air openings of the product or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
6. Never use while sleeping or drowsy.
7. Never drop or insert any object into any opening or hose.
8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
9. Connect this product to a properly grounded outlet only. See Grounding Instructions.

GROUNDING INSTRUCTIONS

This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

DANGER – Improper use of the grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.
Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded. This product is factory equipped with a specific electric cord and plug to permit connection to a proper electric circuit. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. Do not modify the plug provided – if it will not fit the outlet, have the proper outlet installed by a qualified electrician. If the product must be reconnected for use on a different type of electric circuit, the reconnection should be made by qualified service personnel.
If it is necessary to use an extension cord, use only a three wire extension cord that has a three-blade grounding plug, and a three-slot receptacle that will accept the plug on the product.Replace or repair a damaged cord.

The functions may vary from different part no.

| Part no.
Functions| DF-007T
•
---|---|---
Cleaning| Rear Wash| •
Unlimited wash| •
Front Wash| •
Bubble wash| •
Automatic Wash| •
Move Wash| •
H/C Massage Wash| •
Water pressure adjustable| •
Water temp adjustable| •
Tube position adjustable| •
Nozzle self-cleansing| •
Cleaning Nozzle| •
Comfort| Seat Heating| •
Warm Dryer| •
Damper of seat and cover| •
SeatTemp adjustable| •
Air temp adjustable| •
Convenience| Light sensing| •
Instant Heating| •
Remote control flush| •
Stand-up flush| •
Dryer flush| •
Kick flush| •
Kick to open lid/ seat| •
Remote control to open lid / seat| •
Catalyst deodorization| •
Seat sensor| •
Stand-up flush|
Radar Sensor| •
Safety| UV Sterilization| •
Filter steel mesh| •
Air isolation| •
Prevent cross-flow| •
Self-cleaning glaze| •
Eight kinds of protection| •
Nano-antibiotic| •

User Friendly Design

Kick control
New features to offer you an enjoyable experience

Parts Information

Overview

• Feature and functions may vary from different models.
  

Remote Controller

Unit Sideview Right

Unit Sideview Left

Warnings and Safety

Please read thoroughly

First of all, thank you for purchasing our product. To ensure proper and safe use of this product, carefully read this section prior to any usage. Afterwards, store this manual in a safe place for any needed future reference.
The hazards and warnings listed herein are important to our user’s safety. Significant consequences may result from failure to heed warnings. The company will not be held liable for any injuries to the user and damages to the product due to improper usage and/or failure to heed safety warnings.

Explanation of Terms and Symbols

Warning Indicates possible injury resulting from improper usage due to negligence of this sign.

Attention Indicates human injury or property loss that may result in improper usage due to negligence of this sign.

When used with the above “Warning” and “Attention” signs, indicates a strict request to follow noted precautions.

Prohibits any individual from performing any action with this symbol.

Prohibits any individual from dismantling product.

Keep product away from any wet environments, including, but is not limited to, humid environments, close proximities to baths, showers or sinks.

Do not touch!

Do not touch with a wet hand!

Keep away from any extreme heat or fire!

Operate only as instructed!

Pull out the power plug!

Protective grounding.

Warning

This product needs to be properly grounded.

• Risk of electric shock
  *If unsure, contact an electrician. electrical installation company.

Do not touch, insert or pull out the power plug with a wet hand.

• Risk of electric shock.

Do not use a power socket in poor condition or a damaged power plug.

• Risk of fire and/or electric shock.
  

The power socket in use should be within the specified range ( AC 120V)

• Risk of fire and/or electric shock.

Do not pull, damage, bend, twist, stretch, roll, bundle, clamp or squeeze the power cable. Do not place anything on power cable.

• Risk of fire and/or electric shock

If the power cord is damaged, to prevent any injuries or accidents, it should be replaced by a professional.

• Risk of fire and/or electric shock

Do not place a lit cigarette along with other burning objects into the unit.
*Risk of fire.

Do not use during thunderstorms (pull out the power plug during storms).

• Failure in doing so may lead to injury or fault in the product.
  

When the seat ring or the cover plate is damaged, to avoid any harm, be sure to pull off the power plug, close the water source and contact your local distributor for replacement.

• Risk of fire or electric shock.

Regularly pull out the power plug and wipe off any dust on the power plug using a clean dry cloth.
*Risk of fire.

Any person with a disability, the elderly, and children, should be using this product with the supervision of another individual.

• Be advised that sitting on the heated seat for an extended amount of time may result in burns.

This product is not a toy. Advise children not to play with product.
*Risk of injury.

Do not dismantle, repair or alter this  product on your own. Call in a professional, or contact Dyconn Faucet for further advice.

• Risk of fire, electric shock, and/or other accident that may lead to injury.

For cleaning or maintenance of plastic parts, do not use any harsh cleaning agents. (These include, but are not limited to products such as: concentrate sulfuric acid, concentrated nitric acid, glacial acetic acid, carbon tetrachloride, chloroform, acetone, butanone, benzene, methylbenzene, phenol, methylphenol, dimethylformamide, methyl ether, soybean oil, acetate, 40% nitric acid, thick salt acid, 95% alcohol, gasoline, kerosene or brake oil, etc).
*Risk of damaging parts that can lead to accidents and injuries.

Do not add water or detergent into the unit or on to the wireless remote. Do not soak the product with water or cleaner.

• Risk of fire and/or electric shock.

Do not install product in a humid environment or a soak room. Do not spray or soak this product with any form of liquid to prevent any damage to the product.

• Risk of fire and/or electric shock.
  

Do not use polluted water or water meant for industrial.
*Risk of urocystitis or dermatitis.
Untreated water may also cause corrode inner workings of unit and may cause electrical shock or a fire.

Do not apply any force to the unit’s seat and lid. Do not stand on the lid or open or close the lid and the seat forcefully.
*This may result in product damage and/or user injury.

Do not place your hand or any other object into the dryer trap, and do not cover the dryer and dryer trap during product use.

• Risk of fire, electric shock, and/or other accident that may lead to user injury.
  

Do not spray urine at the dryer trap.

• Risk of electric shock.

Read the following for proper battery usage.

• Properly install the battery according to its correct polarity. !

• Remove the battery during long periods without use.

• Replace the battery before it reaches the end of its usage. Failure to do so may result in interrupted control signals. ecover the battery with tape before disposal.
  *This will prevent battery fluid leaks that may cause fire and/or other damages.

• Place the battery out of children and infant reach.
  If battery is swallowed, contact a doctor immediately.

• lf battery fluid leaks onto user, quickly rinse off area using water.

• lf battery fluid gets into eyes, do not rub your eyes. Quickly rinse it with water and consult a doctor immediately.

• May result in vision impairement or blindness.

When the battery is in use, do not do the following operations.

• Do not hold or store with metal objects (such as a necklace or a watch).
• Do not mix new and old batteries.
• Do not pull battery apart battery or throw it into water and/or fire. Battery fluids may cause a fire.

! Attention

Do not use the heated seat or warm dryer temperature for an extended amount of time.
Extended use may result in burns.

While using this product, make sure that the skin is in contact with the seat sensor area. Otherwise, product may not operate correctly.
Children and smaller individuals may have trouble staying in contact with sensor area.

Do not spray urine in the direction of the bidet nozzle.
Doing so may result in blockage to the bidet nozzles and cleaning area.

Do not use your old hose component.
Use the one provided with your product. Anything else connected to the older hose may need to be replaced.
Risk of water leakage and/or property loss/damage.

In case of sudden power failure, remove the power plug and close the angle valve to prevent water leakage.
Risk of water leakage and/or property loss/damage.

Avoid direct sunlight or heat.
Risk of product discoloration.

Do not supply electricity with an external switch. le: connecting the universal part to a timer switch.
Run the risk of issues caused by improperly resetting the thermal breaker.

When the filter is being replaced, be sure to close the water supply angle valve. When the filter is being installed be sure to fasten it with force.
Risk of water leak

Pull out the power plug when the product is in disuse for an extended amount of time. Make sure to shut off the water and remove the water inside the product.
Risk of fire, leaks, and product damage.

When storing or transporting in cold climate, make sure to remove all water from the unit. Product may crack and other damages may occur due to freezing water.
Risk of fire, leaks, and product damage.

Installation

Tools required for installation

Required tools

Required tools for installation. Please have these tools prepared prior to installation.

• Drill (Dia. 0.24in)

• Silicone gun

• Teflon tape

• Knife

• Marking pen

• 0.91 – 0.98 in
  (Spanner model  varies for different pipes)

• Screw driver

• Measuring tape

• Measuring cup
  

Item list (Confirm that all below items are inside the box)

• Intelligent toilet (1 set)
  

• T-valve(1 pc)
  

• Installation Book & User Manual
  

• Remote controller set(1 set) (holder 1 pc, screw 2 pcs)

• Two AAA Battery

• Wax Ring(1 pcs)

• Floor flange(1 pc)

• Toilet bolt (2pcs)

• Washer (Spcs)

• Hexagon bolt(4pcs)

• Tegillum (2pcs)

• Mounting bracket (2pcs)

• bolt(4pcs)

• Nylon sleeve (8pcs)

• Hat head (2pcs)

*  Please confirm all the aforementioned items are inside the package. If anything is missing,
please contact our customer service at 626-768-2849

• Illustrations above are for references only,. Actual objects may look different in person
• We provide you with 2 pcs of conversion nut, each different versions. Please select according
  to your plumbing requirements.

Before you Install

Water pressure check, dimensional drawing

Checking your water supply

The lowest working water pressure is 0.24MPa, the highest water pressure is 0.75MPa.

How to check water pressure

Use this method in the absence of a professional measuring tool.

Open the valve

Open the water angel valve for ten min, if the water can reach 4Litters, then the water pressure meets the lowest working water pressure

Confirm dimensions of product with installation space

Wall

Unit: inches

*The dimension may be slightly changed for different models.

Installing Your Product

Open the box right side up

Remove the accessories first, then remove the unit from the top, as shown in the diagrams below.

Mark your drainage hole with a cross

1. Align the flange with the drain hole, and mark the positions of the four mounting holes of the flange on the ground with a marking pen.
   

2. Place the toilet on the ground with aligning the ground drain hole, place two fixing blocks in the openings on the left and right sides of the toilet bottom, mark the screw mounting hole positions of the fixing block with a marking pen, and then remove the toilet.
   

3. Put the flange on the drain hole, and fix it on the ground with four bolts. Then Seal the flange with glass glue.
   

4. Place the fixing block on the installation position marked by the line drawing pen and fasten it with two bolts.

Install the ceramic body, water supply hose and water filter

1. Place the wax ring on the drain hole at the bottom of the ceramic.
   

2. Align the ceramic drain with the drain hole on the ground, and press down to make the wax ring fully contact with the ground.
   

3. Fix the two sides of the ceramic with two bolts, and finally install the cap.
   

4. Attach the flush water hose to the T-valve and tighten.
   

5. Attach the clean water hose to the T-valve and tighten.
   

6. Connect the T-valve to the water supply and tighten.
   Use gasket to prevent water leakage.
   

7. Finish installation.

Installing the remote

1. Drill two 6mm(0.24 inch) diameter holes on the wall (about 1.77 in deep)
2. Knock the anchors into the hole with a hammer.
3. Secure the holder with anchors.
4. Use the screws to secure the holder to the wall.
5. Remove the battery cover from the backside of the remote to install batteries
6. Once finished, remote is ready to be placed in its holder.
   Detailed steps shown in the diagram below:
   X Please use proper mounting tools for special wall surfaces(such as wood, HOF, etc.)
   XThe remote control holder should be installed away from the bidet’s spray trajectory.
   XThe remote control holder should be installed within reach when seated on unit.
   X Make sure there is nothing to block the transmission between the toilet and its remote.
   

Testing water flow

1. Open the water supply angle valve to maximum as shown in the figure.
   

2. Confirm various connecting parts are not water leaking.

• In case of water leaking, unfasten the nuts again and install them again.

Connecting power

1. Connect to the grounding.

2. Plug in AC 120V power plug.

3. Check to see if the power is on.
   Press the side power button, confirm the toilet is power on.

Testing the product (Checking the side panel buttons and remote control)

• Are all the functions working properly?
  Posterior Wash, Front Wash (Including water pressure & nozzle position adjustment), Heated Dryer, Water & Seat temperature Adjustment, Nozzle cleaning, Anion Deodorization, remote control.
  All functions listed above should be tested.

• checking posterior wash
  Place hand on sensor point (shown in illustration on right), press Posterior on the Side Control Panel or the wireless remote. Use hand to block nozzle spray.
  

Secure the product

1. After all the functions are tested, if toilet still moves, fill gaps with padding.
2. Clean area between the toilet and the floor to prepare for sealant.
3. Use the silicone gun to thoroughly fill the space between the toilet and ground.
   
   Please do not use the toilet within 48 hours after sealing its base.

Matching your remote control code

Your remote control will be matched with a code at the time of delivery. In the case that your remote control malfunctions, match the codes as per the following method.

1. Unplug the product’s plug, press the stop ket for few seconds until the level light is flickered.
   

2. Plug the attaching plug when the remote control get closer to the product.
   

3. The level light stops flickering, and then it is lighted on.
   

4. At the time, the remote control and product is re-connected.

Function Explanations

Under no cleaning and drying mode, and seating the toilet.
“Rotated backward” , rotated it backward for 45° to enter into the front wash mode, which the mode is defaulted to cleaning moving. The cycle of operation: front wash 1 .5mins + drying 4mins + flushing when drying for once.
When the function of front wash is activated, rotates the switch forward to increase the cleaning strength, switch backward to decrease the cleaning strength.

Under no cleaning and drying mode, and seating the toilet.
“Rotated forward” , rotated it forward for 45° to enter into the rear wash mode, which the mode is defaulted to cleaning moving. The cycle of operation: rear wash 1.5mins + drying 4mins + flushing when drying for once.
When the function of front wash is activated, rotates the switch forward to increase the cleaning strength, switch backward to decrease the cleaning strength.

UV Sterilization

After leaving the seat, it will run automatically.
Operate it automatically when leaving seat.The cleaning spout will back to position, and the UV function will be activated after 1 Os, and it is working for 3min, the light of rotated switch becomes purple. After seating, the UV function will stop and the indicator will go out.

• Ultraviolet lamp device is installed on smart toilet.

Stand-up flush

When the seat sensor no longer detects a user, it will automatically flush.
The toilet will only flush once.

Kick Flush

Tap the “Kick Button” with your foot for easy, manual flushing.
Note that the “Kick Flush” function is not available when user is sitting on the toilet seat.

Kick to open I id/seat

Tap the “Kick Button” with your foot to raise your toilet seat/lid.
Tap the kick button once: Lid opens
Tap the kick button twice: Seat raises
Tap the kick button three times: Seat and Lid will close and toilet will flush.

• Posterior/front wash is not available during flushing
  

Radar Sensor

Radar will detect any user within a 3 ft radius
Lid will open automatically for any user within a 3 ft radius and close automatically when it no longer detects a user.

Dryer Flush

Press the “Dryer” button.
The warm air function is activated and a flush is performed.

• Posterior/front wash is not available during flushing.
  

Catalyst deodorization

The function runs automatically.
After the seat is seated, the deodorization fan is automatically turned on, and the deodorization is turned off 3 minutes after leaving the seat.

Light sensing

Automatic operation according to ambient light.
When the night light is turned on, the night light can be turned on/ off automatically through the change of external light intensity.
When there is strong light, the night light will turn off automatically, and when the light is weak, the night light will turn on automatically.

Specifications

Toilet

| | Flush type| Tornado flush
Rough-in| Rough-in 12in

Nozzle

| | Heating type| Instant heating
Washing temp range| OFF/86 “F- 104″F(4 levels)
Safety system| Butterfly thermostat, thermal fuse, flow sensor

Dryer

| | Dryer temp range| OFF/ 95″F -131″F(4 levels)
Dryer air speed| > 4m/s
Safety system| Thermal fuse, bi-metal

Heated seat

| | Heat temp range| OFF/ 82.4″F- 104 “F (4 levels)
Safety system| Thermal fuse

Remote control

| Dimension| 2.01 in(L) 7.48 in(W) 0.87 in(H)
Battery| Two AAA Batteries
Power cable length| Appx. 47.2 in
Product dimension| 26.93 in(L) 15.55 in(W) 19.41 in(H)

Maintenance

Regular maintenance is required to ensure normal use

Note

• Cut off the power and water supply before maintenance.
• Direct water wash to the entire product is prohibited.

Maintenance of product surface and ceramics

• Wipe dust or stains with a soft wet cloth
• A wet soft brush, cloth or sponge may be used to clean the ceramic area
• Do not use abrasive cleaning solutions, such as alcohol, bleach, paint thinner, cresol, benzene, gasoline, etc.
  

WARNING

Do not spray water or detergents on the toilet, remote control or the power cord. Doing so may cause electrick shock or fire.

Maintenance of the nozzle

Press the “Nozzle Clean”” button on the remote control without occupying the seat. The nozzle will extend.
Proceed to clean with a soft toothbrush.
Do not forcefully hold the nozzle, otherwise it may break.
Please change the spout if it blocked.

Troubleshooting

Experiencing issues with your product?

If the user should run into any issues, please consult the troubleshooting guide below. If problem persists, please contact a professional or call Dyconn Faucet at 626-768-2894.

Power button

Power off
{Power light on toilet’s Side Control Panel is not on)| Press rotated switch for 3s, the power light is on.
Electrical Leak| Unplug the power cord, re-connect, and power on.If it is still not working,please unplug again and contact Dyconn Faucetat626-768-2894.
Power Save Mode| Push the power button until the indicator light turns on
Wash functions
Possible Cause| Solution
Bidet nozzle does not spray| No water supply| Wait for water supply to restore
Water valve is switched off| Switch on the valve
Blockage in filter| Clean or exchange the filter
Water hose is twisted| Untangle hose
Water is weak| Waterpressureissettolow| Raise water pressure using remote
Blockage in filter| Clean or exchange the filter
Spray is out of control
Operational failure| Unplug the power, and restart after 1 min
Water is not warm
Water temp. is set to low| Turn up the water temperature using remote
Water leak
Check the water supply system| Call Dyconn Faucet at 626-768-2894.

Wash function does not activate

| Toilet lid may not be properly pushed down.| Check for anything wedged between the seat. Push seat down an the way.
Sensor itself may be broken| Call Dyconn Faucet at 626-768-2894.

Dryer

Dryer not warm| Dyer temp. is set to low| Using the remote, turn up the dryer temperature.
---|---|---
Dryer is broken| Call Dyconn Faucet at 626-768-2894.
Heated seat
Seat temp. not warm|
Possible Cause| Solution
Seat temp. is set to low| Using the remote, turn up the seat temperature.
Power-saving mode is on| Turn off the power-saving mode
Remote Control
Water temperature indicator light starts flashing blue|
Possible Cause| Solution
Battery is low| Replace the battery
Remote control failure   Check the remote control for water| Wipe away water droplets with a dry cloth
Toilet Unit
Weak Flush|
Possible Cause| Solution
Filter is blocked| Clean the filter
Water pressure is low| Check the water source volume (less than0.79 gal in 10 second Use a water pump to enforce the water
Water hose is stuck or twisted| Check water hose to see if it’s twisted or bent in
Siphon jet at bottom of toilet does not work| drainage pipe is leaking| Call Dyconn Faucet at 626-768-2894
S-trap pipeline is stuck| Use a clogging tool
Toilet does not flush     Flush Valve is broken| Call Dyconn Faucet at 626-768-2894
Soft-Closing Feature
Soft-close feature on seat/lid does not work| Possible Cause| Solution
Toilet seat/lid damper is broken| Call Dyconn Faucet at 626-768-2894
Auto open/close lid/seat failure| Auto damper is borken| 1.Unplug the power cord and re-connect after 1 min 2.lf still not working, please all Dyconn Faucet at

626-768-2894

|

Warranty

All Dyconn Faucet products are manufactured and tested with the highest quality standards and rigorous quality control process.
This warranty is limited to the non-commercial use of Dyconn Faucet products purchased and installed in the United States and Canada.

Dyconn Faucet Brand Limited Warranty on Faucets and l{itchen/Bath Accessories

Dyconn Faucet warrants its faucet products to be free from manufacturing defects in material and workmanship during the normal non-commercial use for a period of three (3) years from the initial purchase date by the original owner /end-user for personal household use. Dyconn Faucet also warrants its part and accessory products to be free from manufacturing defects in material and workmanship during the normal non-commercial use for a period of one (1) year from the initial purchase date by the original owner/end-user for personal household use. This warranty is non-transferable between homes or owners and only applicable for residential use. Any commercial or industrial use of Dyconn Faucet products automatically voids the warranty. Any warranty claim must include the original sales receipt as proof of purchase from an Authorized Dealer or Distributor of Dyconn Faucet products.
(Authorized Dealers can be found on the Dyconn Faucet website).

Dyconn Faucet recommends installation of all Dyconn Faucet products by a licensed professional plumber. Dyconn Faucet will not be responsible for any damage or product failure due to improper installation, misuse or the failure to adequately utilize a licensed professional. Proper care and maintenance for all products is standard, like any other household appliance and fixtures to ensure proper function and a lasting product. Instructions are provided in your manual on proper care and maintenance of Dyconn Faucet products.
This warranty will not cover any damages that might be caused by the product. (In some instances States do not allow for such limitations, so this may not apply to all owners).

Any product reported to Dyconn Faucet as defective will be repaired or replaced (with a product of equal value) at the option of Dyconn Faucet. If Dyconn Faucet is not able to replace or repair the product, Dyconn Faucet may elect to refund the original purchase price to the original purchaser in exchange for the return of product. Dyconn Faucet has the full rights to inspect any Dyconn Faucet product reported as defective prior to repair or replacement. Any repair and replacement costs EXCLUDE shipping, labor for removal or re-installation and any consequential or special damages associated with return, replacement and installation of your product. Replacement parts may be obtained by calling 1-855-239-2666 (in the U.S. and Canada), by emailing us at info@dyconnfaucet.com or writing to:

Dyconn Faucet- 382 N. Lemon Avenue #122, Walnut, CA 91789

Dyconn Faucet reserves the rights to modify the warranty at any time, it being understood that any such modifications will not supersede warranty conditions that are applicable at the time of the original sale of products in question.
Though Dyconn Faucet products are certified by various agencies, Dyconn Faucet makes no implication that products comply with any or all local building or plumbing codes. It is the consumer’s responsibility to determine any code compliances when installing and using Dyconn Faucet products.

Limitations of Warranty:

The warranty shall be not apply and be void for incorrect operating procedures, breakages and/or damages caused by fault through improper installation, carelessness, abuse, misuse, misapplication, improper maintenance and alteration of product; damages caused by chemicals, natural corrosion, accident, fire, flood, an act of God, or any casualty. Avoid abrasive cleaners, materials, steel wools and harsh chemicals as these will scratch, damage, and/or dull the products and/or finish of the products and void the warranty. The proper installation of product covered is the responsibility of the original owner/purchaser of the product. Dyconn Faucet neither installs nor supervises the installation nor hires contractors for this purpose; consequently Dyconn Faucet cannot be held responsible for any default breakage, or damages caused thereby or resulting thereof, either directly or indirectly.

This warranty does not apply to Products that have not been installed or operated in accordance with instructions supplied by Dyconn Faucet and all applicable rules, regulations, and legislation pertaining to such installations.
This warranty does not apply to Commercial or Industrial applications of Dyconn Faucet products.

Dyconn Faucet is not responsible or liable for personal injuries or deaths to any person for any direct, special, incidental, or consequential damage, loss of time, loss of profits, inconvenience, incidental expenses, labor or material charges, or any other cost resulting from the use of the product or equipment or pertaining to the application of the present warranty, or resulting from the removal or replacement of any product or element or part covered by this warranty.
In any case, Dyconn Faucet is not liable for any amount over and above the purchase price paid for the Product by the original owner/end-user.

Cleaning and Care

Care should be exercised when cleaning this product. Although its finish is extremely durable, it can be damaged by harsh abrasives and cleaning pads. To clean, use a light, non-abrasive cleaning solution or cleaning polish.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>