DYCONN M14AT Swan LED Backlit Mirror Instruction Manual

Instruction Manual M14AT Swan LED Backlit Mirror

M14AT Swan LED Backlit Mirror

Product Features:
Frameless backlit Mirror
Extra thick frosted LED light
Can be hung vertical or horiztonal
Touch switch on & off/ dim function Anti-fog pad
LED Backlit Mirror
Sizes: 48” W x 36”H (horizontal or vertical)
60” W x 35”H (horizontal or vertical)
70” W x 38”H (horizontal or vertical)
Model:
Catella M09AT, Catela-Plus M10AT, Royal M12AT, Edison M13AT, Swan M14AT, Egret M16AT
For easy installation of your Dyconn Mirror please do the following:
Thoroughly read all instructions before installing the enclosed product.
Read and take note of all safety, care, and maintenance information.
PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE FOR PRODUCT OPERATION AND MAINTENANCE.
Warning : Please read!!

1. Dyconn Faucet LED mirrors should only be installed by a certified electrician.
2. During installation please make sure the circuit breaker or the power source switch has been turned off. Never install the mirror with a live line on.
3. It is recommended to have at least two people available to install the mirror. Remember to wear proper protective gear during instal-lation. All mirror glass is non-tempered glass and can result in sharp shards if the glass is shattered.
4. Please use a certified licensed installer to hang the mirror to the wall. Using the proper anchor and screws for securing the unit to the wallis crucial. Screwing to the stud is recommended.
   Feel free to contact us at 855-239-2666 or info@dyconnfaucet.com

Product Description & Information

Product Features:

• Frameless backlit Mirror
• Extra thick frosted LED light
• Canbe hung vertical or horizontal
• Touch switch on & off
• Touch switch dim function
• Anti-fog pad

Package Content:

• LED backlit Mirror
• Screws
• Studs

Mirror Back Frame Warning: Always switch off the electrical supply at the mains during installation and maintenance.
Do not switch on the electrical supply at the mains until the end of theinstallation.
Tools you will need:

Installation Steps

First, decide whether you want to hang your mirror vertically or horizontally. It is advisable to have one more person help you install the mirror.
Horizontal Mounting

1. Have one person hold the side of the mirror while another person holds the back frame. Pull the bottom of the glass out from the back frame and lift up to separate these two parts.
2. Usean I-Beam level to mount the back frame onto the wall. (use an anchor when installing on drywall, concrete, or tile surfaces)
3. Make sure the circuit breaker for the power source of the mirror is off. Then connect the neutral (White), hot (black), and ground (copper wire or Green) wire between the mirror and the junction box.
4. When hanging mirror horizontally, place the mirror’s side on to the mounting bracket in the metal frame. Then push the bottom of the mirror onto the lock catch tolockit in.
5. Test the mirror. (Make sure to connect all wire between the inner housing and touch sensor switch)

Vertical Mounting

1. Have one person hold the side of the mirror while another person holds the back frame. Pull the bottom of the glass out from the back frame and lift up to separate these two parts.
2. Remove the two horizontal mounts on the back of the frame. Line up the holes on the bracket with the holes placed for the vertical mount and screw the bracket in. Remove the two catch locks located at the bottom of the metal frame by removing its screw.
3. Using an I-Beam level, mount the back frame onto the wall. (Use an anchor when installing on drywall, concrete, or tile surfaces.)
4. Make sure the circuit breaker for the power source of the mirror is off. The connect the neutral (White), hot (black), and ground (copper wire or Green) wire between the mirror and the junction box.
5. Mount the mirror vertically by placing the mirror’s side on to the mounting 0brackets. Two L hooks on the glass should latch on to the mounts. There is no catch lock needed for vertical mounting.
6. Test the mirror.

LED Mirror Power Source FAQ

Scenario 1
(Direct Wired)
This is the most common way to connect the mirror. The LED light & anti fog pad are both controlled by the built-in touch switch on the mirror.
*The LED light is dimmable.
Scenario 2
(Wall Switch)
By doing so, the mirror is now bridged to the wall switch. In order to turn on the mirror,the wall switch needs to be on. The touch switch canbe used to turn on the LED mirror and anti-fog pad. The mirror shuts down once the wall switch is flipped to OFF. Scenario 3
(Wall Switch – No Dimmer)
By doing so, the mirror’s light and anti-fog pad are now controlled by the wall switch. This is without the need touse the built-in touch switch. The touch switch is disabled.
The LED and anti fog pad are now controlled only by the wall switch.
Scenario 4
(Wall Dimmer Switch — Not Accepted)
This is a scenario that is not acceptable. There is no work around for our mirror.
Do not try this way as it will damage the LED driver.

Introducing Tri-Color Mirrors and Additional Features

In the near future, Dyconn Faucet will be upgrading our mirror products to include tri-color options and additional features. Full feature list is listed below:

• Tri-color temperature options: 3000K, 4000K and 6400K
• Dimming Capability (except 72 Inch models)
• Onboard memory – If connected to a switch, the mirror will turn on with the settings last used
• Built-in touch Sensor
• Built-in anti-fog (except 12 x 16 size)
• UL certified

Some tri-color options are alreadly available onfine via resellers and distributors. To easily recognize which items willinclud the newest colors and features, you need only to pay attention ‘o the end character of the model number. If the model number ends with “T* (example: M16AT2432T), then the products will be tri-color and include the newest features.
Please note the following :

• Bypassing touch sensor: When connecting tri-color models and bypassin? the touch sensor toa 1 non-dimmable wall switch, the mirror willonly enable 4000K and will no Tonger be able to select between all available color temperatures.
• Tri-color maximum brightness: The mirror can tun to its full brightness output at 4000K and half of maximum brightness when set at 3000K or 6400K.

Model Chart

Model| Description| # of LED strip| Lumens output| Watts
---|---|---|---|---
M09AT1216W
M09AT2432W|  12 “x16”   2 Frosted Strips
24 “x 32”   2 Frosted Strips| 2
2| 1456
2964| 13.44
27.36
M09AT3036W
M09AT4836W|  30 “x 36”   2 Frosted Strips
48 “x 36”   2 Frosted Strips| 2
2| 3328
3328| 30.72
30.72
   M09AT6035W
M09AT7238W| 60 “x 35”   2 Frosted Strips
72 “x 38”   2 Frosted Strips| 2
2| 3224
3536| 29.76
32.64
M10AT4836W
M10AT6035W| 48 “x 36”   3 Frosted Strips
60 “x 35”   3 Frosted Strips| 1
1| 6448
6838| 59.52
63.12
M10AT7238W
All CAT22W (Round)| 72 “x 38”   3 Frosted Strips Round
22”   LED Frosted Edge| 1
1| 7956
1638| 73.44
15.12
All CAT34W (Round) All CAT42W (Round)| Round 34”   LED Frosted Edge Round
42”   LED Frosted Edge| 1
1| 2600
3250| 24
30
All VAT1824W (Oval) All VAT2535W (Oval)| 18 “x 24”   LED Frosted Edge – Oval
25 “x 34”   LED Frosted Edge – Oval| 1
1| 1456
1456| 13.44
13.44
All VAT3042W (Oval) All VAT3543W (Oval)| 30 “x 42”   LED Frosted Edge – Oval
35 “x 43”   LED Frosted Edge – Oval| 1
1| 2184
2860| 20.16
26.4
M12/M13/M14-AT1216W M12/M13/M14/M16-AT2432W| 12 “x 16”   Frosted LED w/ Silver Edge
24 “x 32”   Frosted LED w/ Silver Edge| 1
1| 1040
2,200| 10.2
23.04
M12/M13/M14/M16-AT3036W M12/M13/M14/M16-AT4836W| 30 “x 36”   Frosted LED w/ Silver Edge
48 “x 36”   Frosted LED w/ Silver Edge| 1
2| 2,604
7072| 27.84
72.96
M12/M13/M14/M16-AT6035W M12/M13/M14/M16-AT7238W| 60 “x 35”   Frosted LED w/ Silver Edge
72 “x 38”   Frosted LED w/ Silver Edge| 2
2| 8,212
9,768| 83.52
97.92
M13AT1216WC
M13AT2432WC| 12 “x 16” Crystal Tri-color LED w/ Silver Edge
24 “x 32” Crystal Tri-color LED w/ Silver Edge| 1
1| 1,824
3,856| 21.47
45.36
M13AT3036WC
M13AT4836WC| 30 “x 36”   Crystal Tri-color LED w/ Silver Edge
24 “x 32” Crystal Tri-color LED w/ Silver Edge| 1
1| 4,556
6,188| 53.6
72.81
M13AT6035WC
M15AT2432W| 30 “x 36”   Crystal Tri-color LED w/ Silver Edge
30 “x 36”   Aluminum Frame, Blk Trim, Gold Foil – 3000K| 1
1| 7,185
3016| 27.84
40.32
M15AT3036W
M15AT2864W| 30 “x 36”   Aluminum Frame, Blk Trim, Gold Foil – 3000K
24 “x 68”   Aluminum Frame, Blk Trim, Gold Foil – 3000K| 1
1| 3016
4368| 27.84
40.32

All #of LED strip, lumens output, and watts is the same with Bluetooth or TV option.

Dyconn Faucet LED Mirror 48-inch and above Frequently Asked Questions &

Troubleshooting Guide

1.Can| connect toa dimmeron the ill to dim the mirtor (ELV or non ELV dimmer)

Answer: Unfortunately,no,the mirror cannot be connected toanELY dimmer ortraditional non-ELV dimmer switch. All Dyconn Faucet mirtors contin low voltage LEDs and the power supply willnot work propery the source AC saltered thiough a wall AC dirmer.

2.Can I connect toa non-dimmer wallswitch?

Answer Yes. Our mirmors can conect to @ non-cimrmable wall switch and use the on/off/dim touch sensor switch on the mirror regularly or you can bypass the touch sensor to allow the non-dimmable wall switch to controlthe LED mirror's light and defogger pad. Please note that bypassing the touch sensor willalso resultin the loss o dimming functionaity. To do so, lease refer to page 7 onthe manual for connecting without touich sensor switch

3.Why does the 72inch mirror not have adimming function?

Answer: In order to provide the maximum ighting output, al our large size mirrors are fitted with dual bands of light strips (except tri-color models). By doing so the 72-inch mirror power consumption exceedsthe capacity o the touch sensor toallow dimming functionlity.

. Whydothe large mirors (481nch and above) not indlude the hanging mounting bracket ke all other smaller mirmors? Wouldnt that be simpler for instalr to hang the mirror?

Answer: We recommend securingthe large mirrors using two wall tuds. The mirror i designed to have the ront mirror glass removeable from the main bracket housing and llow the installer b able to secure the metal housing tothe wall studs. Once the metal housing bracket i secured, hang the mior backontothe housing and connect all wire connections betuween the glass and the mein housing with the help o two or three people.

. How fardoes the wiring extend from the back of the mirror?

Answer: The wiring extends about 24-inches to connect tothe box (box notincluded).

6. Where should the instalerprepare the J-box for wring?

Answer: Al miror vire connections arelocated ead center” of the back housing, regardless ofthe sze of the mirror.

7.Canthe LED Miror be used asthe onlyliht source in the bathroom? Accordingto it lumen output it seems enough for lighting up 2100m?

Answer: We donotrecommend our miors to e the sole light source of any room. The lumens of our LED mirrors might seem high, but the LED mirror' lightis partially confined behind the glass and sourced through the frosted stips (es it was designed to do). ‘This will reduce the lumen output significantly if we are comparing with a recessed down light's lumen output.

FAQfor Tri-color (model # ending with TorWC)

8 Howfardoes the wiring extend from the backaof the mirnor?

Answer.Yes. The elctrician can bypass the touchssensor, havingthe DC power fiom the intemal pover supply feed directly to the LED stips and let the non- immable well switch to control the mirror. The down side s that youwill have to choose between 3000K or 6400K at hlfis brightness or 4000K at s full brightness some wie: soldering might be required)

9.If|connect the mirror to a non-dimmable wal switch can | set the desired light temperature and brightness level?

Answer.Yes,the tri-color models have amemory function allowing the last light temperature and brightness stting to be the recalled whenyou tur on the walswitch. To do so just turn on the light switch on the wallto iniial the power to the mirror, press the touch sensor to select the light temperature, then press and hold the touch sensor switch to dim to the level you lice. Once you have reached your desired ight temperature and brightness, simply tur off the mirror sing the wall switch (don't tur the mirror off by using touch sensor). The next time youuse the mirror,turn on the wall switch and touch one time on the touch sensor and the mirror will turn on with the brightness ‘and temperature settings you set last time.

Troubleshooting:

1.Right out of the box, we connected the AC poweer to the back o the mirmor o see f the mirtor functions properly (before hanging the mirron), but there s no light and touch sensor doesn't iht up. Why s that?

Answer. For the large mirors 48-inch and up),there are wires that need to be connected in order for the mior tofunction. The mirtor lassis designed to be separatectfrom its metal housing during nstalltion.Insalles would be required to disconnectany wiring inside when removing the mirtor glass. We ship the mirors ‘without connecting these wires inside the unit to make installation more convenient.

2. Why does the touch sensor seemto be untesponsive?

Answer: Do not use your fingertips on the touch sensor. Ensure that you are. using the flat part of your finger/thumb (your fingerprint). Please make sure you are using your finger to tap/touch at amoderate speed (once per second). Do not tap/touch the mirnor sensor switch at a speedaster than tuice per second. This willcause the sensor CPUto malfunction. A dircuit breaker reset wil b required to reset the touch sensor.

3.Whyis mymirtor making humming/buzzing noise?

. Why s the LED flickering?

Wall Switch Bypass Instructions

Numbers will correspond to following tags attached to the wires Use the following steps to wire mirror to an electrical wall switch and bypass the touch sensor:

1. Disconnect all connections from the touch sensor (#1-3).
2. Connect the LED Power Supply directly to the 12V DC LED Connector (#1 and #2 circled in red).

Manufacturer Limited Warranty

AUDyconn Faucet productssremanufactured and ested ith thehighest qualy standards and igorous quality contol process This warranty s limited to the non-commercial use of Dyconn Faucet products purchased and nstalledin the United States and Canada Dyconn Faucet Brand Limited Warranty on Faucets and Kitchen/Bath Accessories Dyconn Faucetwarrants its faucet products to be free from manufacturing defects in material and workmanship during the normal non- commerdal use for a period of (3) three years for all non-electical componentitems and (1) one year for all electronic component related items (such as, but are not limited to, products like the sensor faucet and bidet toilet) from the initial purchase date by the original owner/end-user for personal household use. Dyconn Faucet also warrants its part and accessory products to be free from manufacturing defects in material and workmanship during the normal non-commercial use for a period of one (1) year from the initial purchase date by the original owner/end-user for personal household use. This warranty is non-transferable between homes or owners and only applicable for residential use Any commerd al or industrial use of Dyconn Faucet products automatically void the warranty. Any warranty claim must include the original sales receiptas proof of purchase from an Authorized Dealer or Distributor of Dyconn Faucet products:
(Authorized Dealers can be found on the Dyconn Faucet website).
Dyconn Faucetrecommends nstallation of all Dyconn Faucet products by licensed professionals. Dyconn Faucetwill notbe held responsible for any damages or product failure ue toimproper installation, misuse or the falure to adequately uilize a i censed professional. Proper care and maintenance for al products is standard, like any other household appliances and fixtures to ensure proper function and a lasting product Instructions are providedin your manual on the proper care and maintenance of Dyconn Faucet products.
This warrany il not cover any camagesthatmightbe caused by he product (1 some nstances, specific states donotllow forsuch limitations, therefore, tis may not apply to all owners)
Ay and sl warranty i mustinclude the orginal sales receipt s proof of urchase froman Authorzed Deste o Distibutr of Dyconn Faucet products Please contact Dyconn Faucet Support o Sales Department for assistance with the verification process. Any rodctreported toDyconn Faucet s defectvewilberepaied o replaced nithaproductof equal value)atthe company’s disreton [fDyconn Faucetis not able to replace or repair the product, Dyconn Faucetmay elect o refund the original purchase price tothe original purchaser in exchange for the products return. Dyconn Faucet has full ights toinspect any Dyconn Faucet productreported as defective prior to repair or replacement Any repair and replacement costs EXCLUDE shipping, Labor for removal or re-installation, and any consequential or spedal demages assodated with the retun, replacement andinstallation ofyour product To ease the duration and financial burdens of the warranty process for our customers, Dyconn Faucet may request images and/or videos of products to assess the product’s condition and determine the necessary replacement pars. Replacement parts and warranty claims may be obtained by contacting us using one of the following methor
Phone: 1-855-239-2666 (in the U.S. and Canada)
Email info@dyconnfaucet.com
Writetous
Dyconn FaucetWarranty
382 N. Lemon Avenue #122
Walnut CA91789
Dyconn Faucetreserves the fight to modify the warranty at any time, it being understood that any such modifications will not supersede.
warranty conditions that are applicable at the time of the original sale of productsin question.
Though Dyconn Faucet products are certified by various agencies, Dyconn Faucetmakes noimplication that products comply with any or al local building or plumbing codes. tis the consumer’s responsibility to determine any code compliances when installing and using Dyconn Faucetproducts
Limitations of Warranty:
The warranty shall not apply and be voidfor incorrect operating procedures, breakages and/or damages caused by fault through improper installation, carelessness, abuse, misuse, misapplication, improper maintenance and alterai on of product; damages caused by chemicals, natural corrosion, accident, fire, flood, an act of God, or any casualty. Avoid abrasive cleaners, materials, steel wools and harsh chemicals as these will scratch, damage, and/or dull the products and/or finish of the products and void the warranty. The proper installation of product covered is the responsibility of the original owner/purchaser of the product. Dyconn Faucetneither installs nor supervises the. installation nor hires conractors for this purpose; consequently, Dyconn Faucet cannot be held responsible for any defaultbreakage, or damages caused thereby or resulting thereo, either directly or indirectly.
This warranty does notpply toproducs thathave notbeeninstalled or operated in accordance vt nstuctons supplied by Dyconn Faucet and all applicable rules, regulations, and legislation per taining to such installations.
This warranty does not apply to commercial or industial applications of Dyconn Faucet products.
Dyconn Faucetis notresponsible or liable for personalinjuries or deaths to any person for any direct special, incidental,or consequential damage, oss of time, loss of profits, inconvenience, incidental expenses, Labor or material char s, or any other costrestlting from the use of the product or equipment or pertaining t the application of the presentwarranty, or resulting from the removal or replacement of any productor element or part covered by ths warranty.
In any case, Dyconn Faucetis notliable for any amaunt over and above the purchase price paid for the product by the original owner/end-user.
Cleaning and Care
Care should be exercised when cleaning this product. Although its finish is extremely durable, it can be damaged by harsh abrasives and cleaning pads. To dean, use a light, non-abrasive deaning solution or cleaning polish.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>