Jiujiang Aotaoji Trading CP001 Wireless Charger User Manual
- June 10, 2024
- Jiujiang Aotaoji Trading
Table of Contents
**Jiujiang Aotaoji Trading CP001 Wireless Charger
**
Basic parameter
Product name: wireless charger
Product model: CP001
Product size: 6158 15mm (comes with 1.5M charging cable)
Input: 5V/2A,9V/1.67 A
Output: 5/7.5/10/15W(Max)
Frequency: 115-205Khz
Conversion efficiency: > 73o/o
Charging distance: < 5mm
Compatible devices: Qi-enable devices.
Function introduction
-
Please connect the wireless charger to the power supply, make the sucker attach to the back of the phone, and the wireless charger will be charging when it is aligned.
-
Please keep the center position of the mobile phone aligned with the center position of the wireless charger when charging (Refer to the following pictures for placement).
-
If the charger cannot charge properly, it may be in the wrong or protection state. Please check whether there is any metal foreign body placed in the position of the wireless charger. Remove the foreign body (if there is) so that the charger can work normally.
Product introduction
Thank you for choosing our product! This product is a simple wireless charger, which supports fast charging for Qi-enable devices. Please read the instructions carefully in order to quickly understand the parameters and the performance before using it.
Matters needing attention
- In order to protect the sucker adsorption, it is recommended to rem the phone case or use the smooth ones. Please use the wet cloth to up the surface before using.
- Please use the PD 2.0 or QC3.0 adapter (with the output voltage o1 9V/1.67 A or higher) when using it,so that the wireless charger can v-. high power.
- The wireless charger has the overvoltage and overvoltage input pre The output power will be turned off or reduced if use improperly. Plec whether the device is abnormal or improperly used.
- If there is intermittent charging or serious heating during charging,tl receiving coil of the mobile phone and the wireless charging coil are aligned. Please stop charging and try to cool the mobile phone befor positioning again.
- Do not place the metal objects(including iron sheet,ring and metal ~ shell,etc) on the contact surface of wireless charger when charging.
- Please keep the ambient temperature at 0-26 ·c .Do not place the p1 water, fire, or high temperature (over 40 ‘C ) and low temperature (bel Do not allow children to touch the accessories.
- Incorrect use or placement of the product may lead to reduced sel”\ damage to the product. The resultiing liability does not belong to the , responsibility or the manufacturer’s responsibility. Thanks for unders1
- Please clean the product with dry soft cloth. Do not use chemicals, detergent.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radiio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Warning: changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>