Vantron LNG-PRN-0137 Evoss Tablet Vantron LNG-PRN-0137 Evoss Tablet User Manual

Vantron LNG-PRN-0137 Evoss Tablet

Document Information

This table describes the version and release date.

Foreword
Thank you for purchasing the Product. This manual intends to provide guidance and assistance necessary on setting up, operating, or maintaining the Product. Please read this manual and make sure you understand the functionality of the Product before putting it into use.

Intended Users
This manual is intended for:

• Device owners
• Technical support engineers
• Other users

Copyright
Chengdu Vantron Technology Co., Ltd. (“Vantron”) reserves all rights of this manual, including the right to change the content, form, product features, and specifications contained herein at any time without prior notice. The trademarks in this manual, registered or not, are properties of their respective owners. Under no circumstances shall any part of this user manual be copied, reproduced, translated, or sold. This manual is not intended to be altered or used for other purposes unless otherwise permitted in writing by Vantron. Vantron reserves the right of all publicly-released copies of this manual.

Disclaimer
While all information contained herein has been carefully checked to assure its accuracy in technical details and typography, Vantron does not assume any responsibility resulting from any error or features of this manual, nor from improper uses of this manual or the software. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without notice.

Technical Support and Assistance
Should you have any question about the Product that is not covered in this manual, contact your sales representative for solution.

US Office: Vantron Technology, Inc.
Address: 440 Boulder Court, Suite 300 Pleasanton, CA 94566
Tel: 916-202-7042
Email: sales@vantrontech.com

China Office: Chengdu Vantron Technology Co., Ltd.
Address: 6th Floor, 1st Building, No.9, 3rd WuKe East Street, WuHou District, Chengdu, P.R.
China 610045
Tel: 86-28-8512-3930/3931, 8515-7572/6320
Email: sales@vantrontech.com.cn

Regulatory Information
The Product is designed to comply with:
– Part 15 of the FCC Rules;
Please refer to Appendix for Regulatory Compliance Statements. Regulatory certification information is available on-device. Choose Setting > System > Authentication information.

Symbology
This manual uses the following signs to prompt users to pay special attention to relevant information.

• Caution for latent damage to system or harm to personnel
• Attention to important information or regulations

General Safety Instructions
For your safety and prevention of damage to the Tablet, please read and observe carefully the following safety instructions prior to installation and operation. Keep this manual well for future reference.

• Do not disassemble or otherwise modify the Product. Such action may cause heat generation, ignition, electronic shock, or other damages including human injury, and may void your warranty.
• Keep away from heat source, such as heater, heat dissipater, or engine casing.
• Do not insert foreign materials into the USB port or any other opening of the Product as it may cause the Product to malfunction or burn out.
• Use only the adapter, power cord, and batteries that are approved for use with this Product. Otherwise, it may cause fire or explosion.
• Be sure that nothing rests on the power cable and that the cable is located at a place without risk of trips.
• Cut off the power before inspection of the Product to avoid human injury or product damage.

Precautions for Power Cables and Accessories

Use proper power source only. The Product is designed to use 20V DC. Make sure the supply voltage falls within the specified range. Always check whether the Product is DC powered before applying power.

• Place the power cable properly at places without extrusion hazards.
  Cleaning instructions:

  • Power off before cleaning the Product
  • Do not use caustic or aggressive liquids, vapor, or spray
  • Clean with a damp cloth
  • Do not try to clean exposed electronic components unless with a dust collector

• Power off and contact Vantron technical support engineer in case of the following faults:

  • The Product is damaged
  • The temperature is excessively high
  • Fault is still not solved after troubleshooting according to this manual

• Do not use in combustible and explosive environment:

  • Keep away from combustible and explosive environment
  • Keep away from all energized circuits
  • Do not change components unless the power cable is unplugged.

**Precautions for Battery

**

• This battery cannot mix with deposal or twice- recycled batteries in use. Otherwise, for its abnormal charge and discharge, it will cause over-heated, distort, smoke or burning.
• Keep the battery out of children’s reach and prevent them biting or swallowing the battery.
• Do not insert the battery onto the charger for a long time If charging beyond the normal time, the battery is still in the charger, please stop charging. The abnormal charging will cause battery over-heated, distort, smoke or burning.
• Do not put into microwave stove or any other pressure apparatus. Take the battery away from the cellular Tablet or the charger if it is instant heated or leak-out (or odors) and depose it. The bad battery will causes over-heated, smoke or burning.
• Risk of fire or explosion if the battery is replaced by an incorrect type.

Overview

Thank you for choosing Vantron. It is our commitment to provide our valued customers with the state-of-the-art embedded devices and the best product services. As per request from the customer, we provide LNG-PRN-0137 that runs Yocto linux system based on intel Pentium N4200 with a customer logo on the glass cover. This medical tablet is IP64 rated and has a 10-inch LCD with a resolution of 1920 x 1200 to support standard touch controls. Being ‘Application Ready’, the Product has embedded a basic operation system with drivers for the interfaces. Therefore, you just need add your application software only to get the Product ready right away. It can speed Time to Market of your products and save more cost.

LNG-PRN-0137 Hardware Instructions
LNG-PRN-0137 is developed based on Intel Pentium N4200 series.

Product Appearance and Interfaces
Figure 3-1, Figure 3-2, and Figure 3-3 show the top view, bottom view, and front view of the Product.

Features

The features of Vantron LNG-PRN-0137 are listed in Table 3-1.

■  Processor: Intel® Pentium™, N4200, Quad core, 2.5GHz (Max)
■  LPDDR4 2133MHz 8GB
■  1 x M.2 2280 SSD Slot, 1 x SATA
■  1 x LVDS
■  1 x M.2 M-KEY slot, 1x M.2 E-KEY
■  1 x Type-C
■  1 x 10/100 Ethernet
■  TPM Supported
■  2 x Speaker
■  RTC Supported
■  20V Power Supply
■  Yocto Linux

Specifications

Table 3-2 describes the CPU Board specifications.

CPU Board Specifications

System

| Processor| Intel® Pentium™, N4200, Quad core, 2.5GHz (Max)
RAM| LPDDR4 2133MHz (max 8GB )
ROM| 1 x M.2 M-key 2280 SSD Slot (default 256GB)
Display| Resolution| Dual LVDS 1920 x 1200 @ 30Hz
Audio| Audio| 2 x Speaker

Peripheral

| LAN| 1 x 10/100 Ethernet
Security| 1 x TPM
Button| 1 x Standard power
RTC| Supported
Software| OS| Yocto Linux

Power

| Input| 20V Power Type-C/docking Input
Output| 20V 1.2A Max.
Consumption| 20W+
Mechanical| Dimensions| 248.76 x 167.4mm
Gross Weight| 1.05±0.1KG

Environment Condition

| Temperature| Operating: 0℃ ~ 40℃
Cooling Mode| Fanless
Approvals| RoHS Compliant
IP Level| IP64

Dimensions

Interface Description
This chapter describes the hardware features, including switch, jumper, connector and PIN functions. The interface description is based on the connector sketch map. Necessary information such as pictures are attached.

Type-C connector

POGO pin definition
Table 4-1 and Table 4-2 describe the valid signal of connector on the LNG- PRN-0137 board.

Hardware Operation Notes

a) Power preparation: Please confirm the power input is 20V and the current is 2.25A as recommended.
b) Our adapter is applicable to this device only. Do not insert any third-party equipment. We do not assume any liabilities for any damages caused therefrom.

Disposal and Product Warranty

Disposal
When the device comes to end of life, you are suggested to properly dispose of the device for the sake of the environment and safety. Before you dispose of the device, please back up your data and erase it from the device. It is recommended that the device is disassembled prior to disposal in conformity with local regulations. Please ensure that the abandoned batteries are disposed of according to local regulations on waste disposal. Do not throw batteries into fire or put in common waste canister as they are explosive. Products or product packages labeled with the sign of “explosive” should not be disposed of like household waste but delivered to specialized electrical & electronic waste recycling/disposal center. Proper disposal of this sort of waste helps avoid harm and adverse effect upon surroundings and people’s health. Please contact local organizations or recycling/disposal center for more recycling/disposal methods of related products.

Warranty
Product warranty
VANTRON warrants to its CUSTOMER that the Product manufactured by VANTRON, or its subcontractors will conform strictly to the mutually agreed specifications and be free from defects in workmanship and materials (except that which is furnished by the CUSTOMER) upon shipment from VANTRON. VANTRON’s obligation under this warranty is limited to replacing or repairing at its option of the Product which shall, within 12 months or 24 months depending on the Product after shipment, effective from invoice date, be returned to VANTRON’s factory with transportation fee paid by the CUSTOMER and which shall, after examination, be disclosed to VANTRON’s reasonable satisfaction to be thus defective. VANTRON shall bear the transportation fee for the shipment of the Product to the CUSTOMER.

Out-of-Warranty Repair
VANTRON will furnish the repair services for the Product which are out-of- warranty at VANTRON’s then-prevailing rates for such services. At customer’s request, VANTRON will provide components to the CUSTOMER for non-warranty repair. VANTRON will provide this service as long as the components are available in the market; and the CUSTOMER is requested to place a purchase order up front. Parts repaired will have an extended warranty of 3 months.

Returned Products
Any Product found to be defective and covered under warranty pursuant to Clause above, shall be returned to VANTRON only upon the CUSTOMER’s receipt of and with reference to a VANTRON supplied Returned Materials Authorization (RMA) number. VANTRON shall supply an RMA, when required within three (3) working days of request by the CUSTOMER. VANTRON shall submit a new invoice to the CUSTOMER upon shipping of the returned products to the CUSTOMER. Prior to the return of any products by the CUSTOMER due to rejection or warranty defect, the CUSTOMER shall afford VANTRON the opportunity to inspect such products at the CUSTOMER’s location and no Product so inspected shall be returned to VANTRON unless the cause for the rejection or defect is determined to be the responsibility of VANTRON. VANTRON shall in turn provide the CUSTOMER turnaround shipment on defective Product within fourteen (14) working days upon its receipt at VANTRON. If such turnaround cannot be provided by VANTRON due to causes beyond the control of VANTRON. VANTRON shall document such instances and notify the CUSTOMER immediately.

FCC compliance statement
this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE 3: Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. RF exposure information and statement: this device meets government requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. The SAR limit of USA (FCC) is 1.6W/Kg averaged. Has also been tested against this SAR limit. SAR information on this and other pad can be viewed on-line at http://www.fcc.gov/oet/ea/fccid/. Please use the device FCC ID number for search.
To maintain compliance with FCC RF exposure requirements, the use of belt clips, holsters and similar accessories should not contain metallic components in its assembly, the use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.

ISED Canada compliance statement
this device complies with ISED Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

RF exposure information and statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. The SAR limit of ISED is 1.6W/Kg averaged. Has also been tested against this SAR limit. To maintain compliance with ISED RF exposure requirements, the use of belt clips, holsters and similar accessories should not contain metallic components in its assembly, the use of accessories that do not satisfy these requirements may not comply with ISED RF exposure requirements, and should be avoided.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>