SHURE GLXD14 Plus GLX-D Plus Receiver User Guide

: June 10, 2024
: Shure

SHURE GLXD14 Plus GLX-D Plus Receiver

SHURE-GLXD14-Plus-GLX-D-Plus-Receiver-PRODUCT

The GLXD is a wireless receiver system that provides high-quality audio for live performances and events. It uses the latest technology to ensure clear and reliable sound transmission.

Product Important Safety Instructions

READ these instructions.
KEEP these instructions.
HEED all warnings.
FOLLOW all instructions.
DO NOT use this apparatus near water.
CLEAN ONLY with dry cloth.
DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance with the manufacturer’s instructions.
DO NOT install near any heat sources such as open flames, radiators, heat registers.
REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus.
The MAINS plug or an appliance coupler shall remain readily operable.
The airborne noise of the Apparatus does not exceed 70dB (A).
Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection.
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.
Operate this product within its specified operating temperature range.

Product Usage Instructions

Connect the GLXD receiver to the audio input of your mixer or amplifier using the provided cables.
Turn on the GLXD receiver by pressing the power button. The LED indicator will light up to indicate that the receiver is on.
Press the sync button on the receiver and then on the transmitter to pair them. The LED indicators on both devices will blink to indicate that they are syncing.
Adjust the volume on the receiver and your mixer or amplifier to achieve the desired sound level.
To ensure optimal performance, keep the GLXD receiver and transmitter within 30 meters of each other and avoid any obstacles that may interfere with the signal.
When you are finished using the GLXD system, turn off the receiver and transmitter and disconnect them from your mixer or amplifier.
Store the GLXD system in a dry and cool place to prevent damage from moisture and heat.
If you experience any issues with the GLXD system, refer to the troubleshooting section of the user manual or contact qualified service personnel for assistance.

IMPORTANT SAFETY INSTRUCTIONS

READ these instructions.
KEEP these instructions.
HEED all warnings.
FOLLOW all instructions.
DO NOT use this apparatus near water.
CLEAN ONLY with dry cloth.
DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance with the manufacturer’s instructions.
DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open flame sources on the product.
DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace meant of the obsolete outlet.
PROTECT the power cord from being walked on or pinched , particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
ONLY USE attachments/accessories specified by the manufacturer.
USE only with a cart, stand, tripod , bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
UNPLUG this apparatus during lightning storms or when unused for long periods of time.
REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus.
The MAINS plug or an appliance coupler shall remain readily operable.
The airborne noise of the Apparatus does not exceed 70dB (A).
Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection.
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.
Operate this product within its specified operating temperature range.

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.
This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

Set Up the Receiver

Connect the power supply to the receiver and plug the cord into an AC power source.
Connect the audio output to an amplifier or mixer.

Install Transmitter Batteries

Bodypack

Move the locking lever to the open position and slide the battery door open.
Place the battery into the transmitter.
Close the battery door.

Handheld

Unscrew and remove the battery cover.
Place the battery into the transmitter.
Replace and tighten the battery cover.

System Set Up

Important: Before beginning, turn off all receivers and transmitters. Turn on and link each receiver/transmitter pair one at a time to prevent cross-linking.

Turn on a receiver.
Press and hold the group button to select a group (if necessary). If the group is already set, press the channel button to scan for the best available channel.
Turn on a transmitter. The blue RF LED will flash while the transmitter and receiver form a link. When the link has successfully formed, the RF LED will remain illuminated. The transmitter and receiver will remain linked for future usage. Repeat steps 1-3 for each additional receiver and transmitter. Remember to set each receiver to the same group.

_ Note: _Dashes appearing on the group and channel display after a channel selection indicate that frequencies are not available in the selected group. Choose a group that supports more receivers and repeat the linking steps.

Linking Two Transmitters to a Receiver

Only one transmitter can be active at a time to prevent cross-interference. Gain settings for each transmitter can be independently set and stored when the transmitter is active.

Important: Do not turn on and operate both linked transmitters at any time. Turn off both transmitters before beginning.

Press the group button to select a group. The receiver automatically scans the selected group to find the best available channel.
Turn on transmitter 1 and link it to the receiver. Adjust the gain, and then turn off the transmitter.
Turn on transmitter 2 and press and hold the link button on the transmitter and the receiver to link them together. Adjust the gain, and then turn off the transmitter.

Identifying Linked Transmitters and Receivers with Remote ID

Use the remote ID feature to identify linked transmitter and receiver pairs in multiple receiver systems.

To activate remote ID:

Momentarily press the link button on the transmitter or receiver.
The screen of the linked receiver will blink and display ID, while the status LED on the linked transmitter will flash red/green.
To exit remote ID mode, momentarily press the link button or allow the function to timeout.

Gain Adjustment

Momentarily press the gain buttons on the receiver to adjust the gain of a linked transmitter in 1 dB increments. For faster gain adjustments, press and hold the gain buttons.

_ Tip: _Monitor the audio and observe the receiver audio meter level while adjusting the gain to prevent signal overload.

Locking and Unlocking the Controls

The controls of the receiver and transmitter can be locked to prevent unauthorized setting changes or power-off. The lock status is not changed by power cycles.

Locking the Receiver Controls

Simultaneously press and hold the group and channel buttons until LK appears on the screen. Repeat to unlock.

LK is displayed if a locked control is pressed
UN is displayed momentarily to confirm the unlock command

Locking the Transmitter Controls

To lock directly from the transmitter

Start with the transmitter off, then press and hold the link button while turning on the transmitter. Release the link button when the transmitter powers on to prevent an accidental factory reset. The lock icon appears on the receiver screen when locked. Repeat sequence to unlock.

To lock from the receiver front panel

Simultaneously press and hold the group and link buttons for approximately 2 seconds until the flashing lock icon appears on the receiver screen. Repeat sequence to unlock.

Note: The transmitter status LED will flash if a locked switch is set to the off position.

Firmware

New versions of the firmware can be uploaded and installed using the Shure Update Utility tool.
Download Shure Update Utility from shure.com

Specifications

Tuning Bandwidth

Z2	2400 – 2483.5 MHz
Z3	2400 – 2483.5 MHz and 5725 – 5850 MHz
Z4	2400 – 2483.5 MHz and 5725 – 5875 MHz
Z5	2400 – 2483.5 MHz and 5725 – 5825 MHz

Dependent on frequency band transmit Mode

Shure proprietary digital

RF Output Power

10 mW E.I.R.P. maximum

Ambient Temperature Range

SHURE-GLXD14-Plus-GLX-D-Plus-Receiver-FIG-4

Polarity

Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of lowimpedance output) and the tip of the high impedance 1 /4-inch output.

GLXD4+

Power Requirements
- 14.5 V – 17 V, 600 mA
Antenna Type
- Dual-band ½ Wave Sleeve Dipole, non-removable

GLXD1+

Power Requirements
- 3.6 V
- Rechargeable Li-Ion
Antenna Type
- Dual-band Internal Monopole

GLXD2+

Power Requirements
- 3.6 V
- Rechargeable Li-Ion

In the European Union and the United Kingdom, this label indicates that the A batteries in this product should be collected separately and not be disposed of with household waste. Substances in batteries can have a potential negative impact on health and the environment and you have a role in recycling waste batteries thus contributing to the protection, preservation, and improvement of the quality of the environment. You should contact your local authority or retailer for details of the collection and recycling schemes available. Please consider the environment, electric products and packaging are part of regional recycling schemes and do not belong to regular household waste.

WARNING

Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat above 140° F (60°C), or incinerate.
Follow instructions from manufacturer
Only use Shure charger to recharge Shure rechargeable batteries
WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type.
Never put batteries in mouth. If swallowed, contact your physician or local poison control center
Do not short circuit; may cause burns or catch fire
Do not charge or use battery packs other than Shure rechargeable batteries
Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs.
Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like
Do not immerse the battery in liquid such as water, beverages, or other fluids.
Do not attach or insert battery with polarity reversed.
Keep away from small children.
Do not use abnormal batteries.
Pack the battery securely for transport.

Note

This equipment is intended to be used in professional audio applications.
EMC conformance is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performance.
Use this battery charger only with the Shure charging modules and battery packs for which it is designed. Use with other than the specified modules and battery packs may increase the risk of fire or explosion.
Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Certified under FCC Part 15

Shure has determined that this product is a Class B harmonized product. The following sections provide country-specific EMC/EMI or product safety information.

Certifications

FCC ID: DD4GLXD4Z3, DD4GLXD1Z3, DD4GLXD2Z3 IC: 616A-GLXD4Z3, 616A- GLXD1Z3, 616A-GLXD2Z3

CAN ICES-003 (B)/NMB-003(8)

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
The antenna(s) must be installed such that a minimum separation distance of 20 cm is maintained between the radiator (antenna) and all persons at all times.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Certified by ISED in Canada under RSS-247 and RSS-GEN. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

Connection and use of this communications equipment is permitted by the Nigerian Communications Commission.

Waste Electrical and Electronic Equipment (WEEE) Directive

In the European Union and the United Kingdom, this label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling. REACH (Registration, Evaluation, Authorization of Chemicals) is the European Union (EU) and the United Kingdom (UK) chemical substances regulatory framework. Information on substances of very high concern contained in Shure products in a concentration above 0.1 % weight over weight (w/w) is available upon request.

CE Notice: Hereby, Shure Incorporated declares that this product with CE Marking has been determined to be in compliance with European Union requirements. The full text of the EU declaration of Conformity is available at the following site: https://www.shure.com/en-EU/support/declarations-of- conformity.

Authorized European representative:

Shure Europe GmbH

Department: Global Compliance
Jakob-Dieffenbacher-Sir. 12 75031 Eppingen, Germany
Phone: +49-7262-92 49 O
Fax: +49-7262-92 49 11 4
Email: EMEAsupport@shure.de

UKCA Notice: Hereby, Shure Incorporated declares that this product with UKCA Marking has been determined to be in compliance with UKCA requirements. The full text of the UK declaration of Conformity is available at the following site: https://www.shure.com/en-GB/support/declarations-of- conformity.

UK Importer/ UK Rep.
Shure UK Limited
Unit 2, The 10 Centre, Lea Road, Waltham Abbey, Essex, EN9 1 AS, UK

Frequency Tables

22 (2.4 GHz only)

Group 1 (2.4 GHz)

Gr 1 – Ch 1| 2424| 2425| 2442| 2443| 2462| 2464
Gr 1 – Ch 2| 2418| 2419| 2448| 2450| 2469| 2471
Gr 1 • Ch 3| 2411| 2413| 2430| 2431| 2476| 2477
Gr 1 – Ch 4| 2405| 2406| 2436| 2437| 2455| 2457

Group 2 (2.4 GHz)

Gr 2 – Ch 1| 2423| 2424| 2443| 2444| 2473| 2474
Gr 2 – Ch 2| 2404| 2405| 2426| 2427| 2456| 2457
Gr 2-Ch 3| 2410| 2411| 2431| 2432| 2448| 2449
Gr 2- Ch 4| 2417| 2418| 2451| 2452| 2468| 2469
Gr 2 – Ch 5| 2437| 2438| 2462| 2463| 2477| 2478

Group 3 (2.4 GHz)

Gr 3 – Ch 1| 2415| 2416| 2443
Gr 3- Ch 2| 2422| 2423| 2439
Gr 3 • Ch 3| 2426| 2427| 2457
Gr 3 · Ch 4| 2447| 2448| 2468
Gr 3- Ch 5| 2409| 2451| 2452
Gr 3 · Ch 6| 2431| 2462| 2463
Gr 3 – Ch 7| 2404| 2473| 2474
Gr 3 · Ch 8| 2435| 2477| 2478

Group 4 (2.4 GHz)

2404| 2406| 2408| 2410| 2412| 2414
2416| 2418| 2420| 2422| 2424| 2426
2428| 2430| 2432| 2434| 2436| 2438
2440| 2442| 2444| 2446| 2448| 2450
2452| 2454| 2456| 2458| 2460| 2462
2464| 2466| 2468| 2470| 2472| 2474
2476| 2478| | | |

Group A (2.4 GHz)

2405| 2412| 2418| 2425| 2431| 2438
2444| 2450| 2457| 2464| 2471| 2477

Group B (2.4 GHz)

2404| 2409| 2414| 2419| 2425| 2431
2436| 2441| 2446| 2452| 2458| 2463
2468| 2473| 2478| | |

Z3

Group 1 (2.4 GHz)

Gr 1 · Ch 1| 2405| 2323| 2441| 2465
Gr 1 • Ch 2| 2411| 2429| 2447| 2471
Gr 1 · Ch 3| 2417| 2435| 2453| 2477

Group 2 (2.4 GHz)

Gr 2 · Ch 1| 2404| 2424| 2444| 2464
Gr 2 · Ch 2| 2409| 2429| 2449| 2469
Gr 2 · Ch 3| 2414| 2434| 2454| 2474
Gr 2 · Ch 4| 2419| 2439| 2459| 2478

Group 3 (2.4 GHz)

2405| 2408| 2411| 2414| 2417| 2420
2423| 2426| 2429| 2432| 2435| 2438
2441| 2444| 2447| 2450| 2453| 2456
2459| 2462| 2465| 2468| 2471| 2474
2477| | | | |

Group A (2.4 GHz)

2405| 2411| 2417| 2423| 2429| 2435
2441| 2447| 2453| 2459| 2465| 2471
2477| | | | |

Group B (2.4 GHz)

2404| 2409| 2414| 2419| 2424| 2429
2434| 2439| 2444| 2449| 2454| 2459
2464| 2469| 2474| 2478| |

Group 1 (5.8 GHz)

Gr 1 • Ch 1| 5730| 5760| 5790| 5820
Gr 1 – Ch 2| 5736| 5766| 5796| 5826
Gr 1 · Ch 3| 5742| 5772| 5802| 5832
Gr 1 · Ch 4| 5748| 5778| 5808| 5838
Gr 1 – Ch 5| 5754| 5784| 5814| 5845

Group 2 (5.8 GHz)

Gr 2 • Ch 1| 5729| 5759| 5789| 5819
Gr 2 • Ch 2| 5734| 5764| 5794| 5824
Gr 2- Ch 3| 5739| 5769| 5799| 5829
Gr 2 • Ch 4| 5744| 5774| 5804| 5836
Gr 2 · Ch 5| 5749| 5779| 5809| 5841
Gr 2 • Ch 6| 5754| 5784| 5814| 5846

Group 3 (5.8 GHz)

5730| 5733| 5736| 5739| 5742| 5745
5748| 5751| 5754| 5757| 5760| 5763
5766| 5769| 5772| 5775| 5778| 5781
5784| 5787| 5790| 5793| 5796| 5799
5802| 5805| 5808| 5811| 5814| 5817
5820| 5823| 5826| 5829| 5832| 5835
5838| 5841| 5845| | |

Group A (5.8 GHz)

5730| 5736| 5742| 5748| 5754| 5760
5766| 5772| 5778| 5784| 5790| 5796
5802| 5808| 5814| 5820| 5826| 5832
5838| 5845| | | |

Group B (5.8 GHz)

5729| 5734| 5739| 5744| 5749| 5754
5759| 5764| 5769| 5774| 5779| 5784
5789| 5794| 5799| 5804| 5809| 5814
5819| 5824| 5829| 5836| 5841| 5846

Z4

Group 1 (2.4 GHz)

Gr 1 – Ch 1| 2405| 2323| 2441| 2465
Gr 1 – Ch 2| 2411| 2429| 2447| 2471
Gr 1 – Ch 3| 2417| 2435| 2453| 2477

Group 2 (2.4 GHz)

Gr 2- Ch 1| 2404| 2424| 2444| 2464
Gr 2- Ch 2| 2409| 2429| 2449| 2469
Gr 2 – Ch 3| 2414| 2434| 2454| 2474
Gr 2- Ch 4| 2419| 2439| 2459| 2478

Group 3 (2.4 GHz)

2405| 2408| 2411| 2414| 2417| 2420
2423| 2426| 2429| 2432| 2435| 2438
2441| 2444| 2447| 2450| 2453| 2456
2459| 2462| 2465| 2468| 2471| 2474
2477| | | | |

Group A (2.4 GHz)

2405| 2411| 2417| 2423| 2429| 2435
2441| 2447| 2453| 2459| 2465| 2471
2477| | | | |

Group B (2.4 GHz)

2404| 2409| 2414| 2419| 2424| 2429
2434| 2439| 2444| 2449| 2454| 2459
2464| 2469| 2474| 2478| |

Group 1 (5.8 GHz)

Gr 1 – Ch 1| 5730| 5766| 5802| 5838
Gr 1 – Ch 2| 5736| 5772| 5808| 5844
Gr 1 – Ch 3| 5742| 5778| 5814| 5851
Gr 1 · Ch 4| 5748| 5784| 5820| 5858
Gr 1 – Ch 5| 5754| 5790| 5826| 5864
Gr 1 – Ch 6| 5760| 5796| 5832| 5870

Group 2 (5.8 GHz)

Gr 2 – Ch 1| 5729| 5764| 5799| 5834
Gr 2- Ch 2| 5734| 5769| 5804| 5839
Gr 2 – Ch 3| 5739| 5774| 5809| 5850
Gr 2 – Ch 4| 5744| 5779| 5814| 5856
Gr 2 • Ch 5| 5749| 5784| 5819| 5861
Gr 2- Ch 6| 5754| 5789| 5824| 5866
Gr 2- Ch 7| 5759| 5794| 5829| 5871

Group 3 (5.8 GHz)

5730| 5733| 5736| 5739| 5742| 5745
5748| 5751| 5754| 5757| 5760| 5763
5766| 5769| 5772| 5775| 5778| 5781
5784| 5787| 5790| 5793| 5796| 5799
5802| 5805| 5808| 5811| 5814| 5817
5820| 5823| 5826| 5829| 5832| 5835
5838| 5841| 5844| 5847| 5851| 5855
5858| 5861| 5864| 5867| 5870|

Group A (5.8 GHz)

5730| 5736| 5742| 5748| 5754| 5760
5766| 5772| 5778| 5784| 5790| 5796
5802| 5808| 5814| 5820| 5826| 5832
5838| 5844| 5851| 5858| 5864| 5870

Group B (5.8 GHz)

5729| 5734| 5739| 5744| 5749| 5754
5759| 5764| 5769| 5774| 5779| 5784
5789| 5794| 5799| 5804| 5809| 5814
5819| 5824| 5829| 5834| 5839| 5844
5850| 5856| 5861| 5866| 5871|

Z5

Group 1 (2.4 GHz)

Gr 1 – Ch 1| 2405| 2323| 2441| 2465
Gr 1 • Ch 2| 2411| 2429| 2447| 2471
Gr 1 · Ch 3| 2417| 2435| 2453| 2477

Group 2 (2.4 GHz)

Gr 2 • Ch 1| 2404| 2424| 2444| 2464
Gr 2 · Ch 2| 2409| 2429| 2449| 2469
Gr 2 – Ch 3| 2414| 2434| 2454| 2474
Gr 2- Ch 4| 2419| 2439| 2459| 2478

Group 3 (2.4 GHz)

2405| 2408| 2411| 2414| 2417| 2420
2423| 2426| 2429| 2432| 2435| 2438
2441| 2444| 2447| 2450| 2453| 2456
2459| 2462| 2465| 2468| 2471| 2474
2477| | | | |

Group A (2.4 GHz)

2405| 2411| 2417| 2423| 2429| 2435
2441| 2447| 2453| 2459| 2465| 2471
2477| | | | |

Group B (2.4 GHz)

2404| 2409| 2414| 2419| 2424| 2429
2434| 2439| 2444| 2449| 2454| 2459
2464| 2469| 2474| 2478| |

Group 1 (5.8 GHz)

Gr 1 – Ch 1| 5730| 5754| 5778| 5802
Gr 1 – Ch 2| 5736| 5760| 5784| 5808
Gr 1 – Ch 3| 5742| 5766| 5790| 5814
Gr 1 – Ch 4| 5748| 5772| 5796| 5820

Group 2 (5.8 GHz)

Gr 2 – Ch 1| 5729| 5753| 5778| 5803
Gr2- Ch 2| 5733| 5758| 5783| 5808
Gr 2 – Ch 3| 5738| 5763| 5788| 5813
Gr2- Ch 4| 5743| 5768| 5793| 5817
Gr 2- Ch 5| 5748| 5773| 5798| 5821

Group 3 (5.8 GHz)

5730| 5733| 5736| 5739| 5742| 5745
5748| 5751| 5754| 5757| 5760| 5763
5766| 5769| 5772| 5775| 5778| 5781
5784| 5787| 5790| 5793| 5796| 5799
5802| 5805| 5808| 5811| 5814| 5817
5820| | | | |

Group A (5.8 GHz)

5730| 5736| 5742| 5748| 5754| 5760
5766| 5772| 5778| 5784| 5790| 5796
5802| 5808| 5814| 5820| |

Group B (5.8 GHz)

5729| 5734| 5739| 5744| 5749| 5754
5759| 5764| 5769| 5774| 5779| 5784
5789| 5794| 5799| 5804| 5809| 5814
5820| | | | |

WARRANTY

LIMITED WARRANTY

Shure Incorporated (“Shure”) hereby warrants to the original consumer purchaser only that, except as otherwise specified below, this product will be free In normal use of any defects in materials and workmanship for a period of two (2) years from the consumer’s original date of purchase directly from Shure or from a Shure-authorized reseller. Any rechargeable batteries contained in or packaged with this product are so warranted for a period of one (1) year from the consumer’s original date of purchase. However, rechargeable batteries are consumable and their capacity will be reduced over time based on temperature, amount of time in storage, charging cycles, and other factors; hence reduction in battery capacity does not constitute a defect in material or workmanship.

All its sole option, Shure will repair or replace the defective product and promptly return it to you. In order for this warranty to be valid, the consumer must, at the time the product is returned, provide proof of purchase in the form of the original purchase receipt directly from Shure or from a Shure authorized reseller. If Shure elects to replace the defective product, then Shure reserves the right to replace the defective product with another product of the same model or a model of at least comparable quality and features in Shure’s sole determination. If you believe this product is defective within the warranty period, carefully repack the unit, insure it and return it with proof of purchase, postage prepaid, to Shure Incorporated, Attention: Service Department, at the address below.

Outside of the United States, return the product to your dealer or Authorized Service Center. Addresses are listed on www.Shure.com or can be obtained by contacting Shure at the address listed below. This warranty Is not transferable. This warranty does not apply in cases of abuse or misuse of the product, use contrary to Shure’s instruction, ordinary wear and tear, an act of God, negligent use, purchase from a party other than Shure or a Shure-authorized reseller, unauthorized repair, or modification of the product.

ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED TO THE EXTENT PERMITTED UNDER APPLICABLE LAWS AND, TO THE EXTENT NOT PERMITTED, ARE HEREBY LIMITED TO THE DURATION AND TERMS OF THIS WARRANTY. SHURE ALSO HEREBY DISCLAIMS ALL LIABILITY FOR INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. This warranty does not restrict the rights of the consumer mandated under applicable laws.

THIS WARRANTY SUPERSEDES ALL OTHER WARRANTIES THAT ARE ASSOCIATED OR INCLUDED WITH THIS PRODUCT, EXCEPT THAT ANY SOFTWARE CONTAINED IN OR PACKAGED WITH THIS PRODUCT IS EXCLUDED FROM THIS WARRANTY AND INSTEAD SHALL BE COVERED BY THE WARRANTY, IF ANY, PROVIDED IN SHU RE’S END USER LICENSE AGREEMENT ACCOMPANYING SUCH SOFTWARE.

FOR ORIGINAL PURCHASES IN AUSTRALIA ONLY

LIMITED WARRANTY AGAINST DEFECTS

Shure Incorporated (“Shure”) hereby warrants to the original consumer purchaser in Australia only that, except as otherwise specified below. this product will be free In normal use of any defects in materials and workmanship for a period of two (2) years from the consumer’s original date of purchase directly from Shure or from a Shure authorized reseller. Any rechargeable batteries contained in or packaged with this product are so warranted for a period of one (1) year from the consumer’s original date of purchase. However, rechargeable batteries are consumable and their capacity will be reduced over time based on temperature, amount of time in storage, charging cycles, and other factors; hence reduction in battery capacity does not constitute a defect in material or workmanship.

At its sole option, Shure will repair or replace the defective product and promptly return it to you. In order for this warranty to be valid, the consumer must, at the time the product is returned, provide proof of purchase in the form of the original purchase receipt directly from Shure or from a Shure authorized reseller. If Shure elects to replace the defective product, then Shure reserves the right to replace the defective product with another product of the same model or a model of at least comparable quality and features in Shure’s sole determination.

If you believe this product Is defective within the warranty period, carefully repack the unit, insure it (at your expense, if you want the benefit of insurance) and return it with proof of purchase, postage paid by you, to Shure Incorporated, Attention: Service Department, at the address below. Outside of the United States, return the product to your dealer or Authorized Service Center. Addresses are listed on www.Shure.com or can be obtained by contacting Shure at the address listed below. This warranty is not transferable. This warranty does not apply in cases of abuse or misuse of the product, use contrary to Shure’s instruction, ordinary wear and tear, an act of God, negligent use, purchase from a party other than Shure or a Shure- authorized reseller, unauthorized repair, or modification of the product.

ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED TO THE EXTENT PERMITTED UNDER APPLICABLE LAWS AND, TO THE EXTENT NOT PERMITTED, ARE HEREBY LIMITED TO THE EXTENT PERMITTED TO THE DURATION AND TERMS OF THIS WARRANTY. SHURE ALSO HEREBY DISCLAIMS ALL LIABILITY FOR INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES FOR ANY PURCHASER ACQUIRING THIS PRODUCT, EXCEPT THAT THIS DOES NOT CONSTITUTE A DISCLAIMER OF RIGHTS GUARANTEED TO ANY “CONSUMER” UNDER THE AUSTRALIAN CONSUMER LAW.

This warranty gives purchasers of this product in Australia specific legal rights which are in addition to the rights and remedies of consumers under the Australian Consumer Law, which cannot be excluded or limited. If you are a “consumer” under the Australian Consumer Law, you are entitled to a replacement or refund for a major failure and for compensation for any other reasonably forseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. THIS WARRANTY SUPERSEDES ALL OTHER WARRANTIES THAT ARE ASSOCIATED OR INCLUDED WITH THIS PRODUCT, EXCEPT THAT ANY SOFTWARE CONTAINED IN OR PACKAGED WITH THIS PRODUCT IS EXCLUDED FROM THIS WARRANTY AND INSTEAD SHALL BE COVERED BY THE WARRANTY, IF ANY, PROVIDED IN SHU RE’S END USER LICENSE AGREEMENT ACCOMPANYING SUCH SOFTWARE.

CONTACTS

United States, Canada, Latin

America, Caribbean: Shure Incorporated 5800 West Touhy Avenue Niles, IL 60714-4608 USA
Phone: 847-600-2000
Fax: 847-600-1212 (USA)
Fax: 847-600-6446
Email: info@shure.com