SENGOKU L A LTD HME-GS10 Far Infrared Graphite Heater User Manual
- June 10, 2024
- SENGOKU L A LTD
Table of Contents
SENGOKU L A LTD HME-GS10 Far Infrared Graphite Heater
IMPORTANT INSTRUCTIONS
READ CAREFULLY-The far infrared graphite heater is designed for safe
operation. Nevertheless, installation, maintenance and operation of .
Observing the heater can be dangerous the following procedures will reduce the
risk of fire, electric shock, or injury and keep installation time to a
minumum.
When using electrical appliances, basic precautions should always be followed
to reduce the risk of fire, electric shock, and injury, including the
following:
Read all instruction before using this heater.
-
Remove the unit form it’s packaging and check to make sure it is in good condition before using.
-
Make sure all holding tapes are removed before using.
-
Do not let children play with parts of package (such as plastic bags).
-
Check the household voltage to ensure it matches the heater’s rated specification.
-
Check the power cord and plug carefully before used, to make sure that they are not damaged. 6 . Before unplugging the power cord, be sure to turn off the power button. When turning unit on/off be sure your hands are dry to prevent electric shock.
-
Do not use heater near flammable objects, like furniture, pillows, bedding, paper, clothes, curtains,
etc.; they must be at least 3 feet (1 meter) away from the heater, and not facing heater directly. -
Do not use near or in the immediate vicinity of a bath or swimming pool or any source of liquid.
-
To protect against electric shock, do not immerse cord or plug in water or any other liquid.
-
Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause and electric shock, fire or damage to the heater.
-
Always unplug the heater when not in use.
-
Do not allow cord to overhang the counter top where it can be easily pulled by children.
-
Do not touch or put foreign objects into the grill while in operation.
-
Do not leave the appliance unattended when in use.
-
This heater is not intended for use in bathrooms, laundry and similar indoor locations, never place heater where it may fall into a bathtub or other water container.
-
No liability can be accepted for any damage caused by noncompliance with these instructions or any other improper use or mishandling.
-
This appliance is not intended for use by anyone including children or people with disabilities 17. This appliance is not intended for use by anyone including children or people with disabilities
-
If the supply cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
-
Parts of the heater may exceed 200 /392 , contact with the heating tube, reflector, or metal parts near the heating tube, may cause severe BURNS. To avoid burns, do not touch hot surface.
-
Always allow heating element to cool at least 10 minutes before touching the heating tube or adjacent part.
-
This product contains recyclable materials. Do not dispose this product as unsorted municipal waste. Please contact your local municipality for the nearest collection point.
-
This heater is hot when in use. To avoid burns, do not touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, etc. and curtains at least 3 feet (1m) from the heater.
-
Extreme caution is necessary when any heater is used near children, or people with disabilities. Heater can NOT be left unattended when operating.
-
Do not operate any heater if it malfunctions. Disconnect power at service panel and have heater inspected by a reputable electrician before reusing.
-
To disconnect heater, turn controls to off, and turn off power to heater circuit at main disconnect panel (or operate internal disconnect switch if provided).
-
This heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline paint, or flammable vapors or liquids are used or stored.
-
Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury.
SAVE THESE INSTRUCTIONS
Specification
| Rating | 120VAC 60Hz 1200W |
|---|---|
| Main unit dimensions | Heater: W30.12 D5.3 H5.51(in)/W765 D132 H140(mm) |
Stand: W33.46 D33.46H(37.40 to 59.06) (in)
/W850 D850 H(950-1500)(mm)
Mass ( Weight)| 13.18(lbs)/5.98(kg)
Power cord| Rubber cord, length 7.87(ft)/2.4(m)
Heater| Far infrared electric heater 1 pcs
Stand| H(MAX) 150cm – H(MIN) 95cm/H(MAX) 59.06 (in) – H(MIN) 37.40 (in)
Safety device| Overheat protection, Tip over function
Product Features
- INSTANT HEAT
- WEATHERPROOF
- TWO HEAT SETTINGS
- ODORLESS
- SILENT
FREESTANDING
A lightweight and sturdy stand allows portable installation.
TIP-OVER PROTECTION
Tip-over protection to ensure safe operation. The unit will shut down
immediately if tips over or falls to prevent tip-over-related hazards.
ASSEMBLY INSTRUCTIONS
- The heater must be properly installed before it is used.
- The heater can be used indoor or outdoor with provided stand only.
- User must follow these instructions to reduce the risk of fire, electric shock, or injury.
- Do not alter or make any changes to the unit.
A.Stand assembly
Stand Accessories List
- Put foot(H14) into the base(H8) ,and then put the Holder(H15) on top of the Base(H8), finally put Screws(H7) into the hole as shownin Fig-a.
- Turn to the back side, secure the fixed parts (H10) with Screws(H7) as shown in Fig-b.
- Secure Fastner(H9)& Pole (H16) as show in Fig-c, then turn over to the back side,secure Screw(H11), Spring washer(H12), Flat washer (H13)as shown in Fig-d.
B.Heater & Stand installtion
Installation hardware contents
- Tighten the hand knob screw to secure the stand positions as shown in Fig-e.
- Secure the bracket (H5) on the back of heater with 2 nuts (H3) using the wrench as shown in Fig – f.
- Hanging the heater’s bracket on the stand’s bracket as shown in Fig – g
- Fasten Screw (H1) with wing nut (H2) as shown in Fig – h
- Assembly the protection bracket on the heater, the top panel on protection bracket could be clipped into the screws as shown in Fig – i.
- Fasten the protection bracket with 2 wing nuts (H2), and secure the top 2 screws using the screwdriver as shown in Fig – j.
- Secure the power cord with the zip ties (H6) as shown in Fig – k.
WANING! FOR OUTDOOR USE, MUST PLUG INTO GFCI OUTLET.
WARNING
THE HEATER MUST BE PLACED ON A FLAT, STABLE SURFACE FOR USE WITH THE STAND.
THE HEIGHT OF STAND WITH HEATER IS 60 INCHES.
THE POWER CORD MUST BE PLUGGED INTO A GFCI OUTLET FOR OUTDOOR USE.
Noted: The heater has a tilt protection function. When the heater exceeds
a 60 ° angle, it automatically stops working.
Grounding instructions
CAUTION: This heater is for use on 120 volts. The cord has a plug as
shown in below No adapter is available for this blade configuration, and none
should be used. The type outlet is a 120 volts grounding outlet. When properly
installed, it provides a ground connection through the cord to the heater to
protect the operator from electric shock.
Attention: Digital display position should be on left for correct installation direction
OPERATING INSTRUCTION
- a) The heater must be properly installed before it is used.
- b) The heater can be used indoor or outdoor.
- c) User-operated devices intended to reduce the risk of fire, electric shock, or injury. ALL INSTRUCTIONS MUST BE FOLLOWED.
- d) Do not change the heater structure.
- e) Follow instructions and cautionary statements for cleaning, user maintenance, operations.
- f) Any service to the unit must be performed by a manufacturer representative.
- PLUG the unit into a plug socket, make sure the power supply is the same as rated
- PRESS the power button on the left side of the heater
- TURN ON / OFF the heater by remote control.
- DOWN & UP BUTTON, setting the heat level or timer.
OPERATIONBYREMOTECONTROLLER:
The heater is operated from the remote control supplied . Insert 2 x AAA
Alkaline batteries into the remote control.
Remote Control Function
Button| Function ( Heater On)| Function ( Heater Off)
1| Turns heater on or off|
2| Increase Heat Level or Timer hours| Turns heater on to Level 1 (minimum)
3| Decrease Heat Level orTimer Hours| Turns heater on to Level 2 ( Maximum)
4| Enable Heat Leveladjustment|
5| Enable Timer adjustment| 0-24
- POWER BUTTON: Turns heater on or off.
- UP BUTTON: Increases the temperature and timer level .
- DOWN BUTTON: Decreases temperature and timer level.
- LEVEL BUTTON: Use to adjust heat levels (LO-HI). Press the Level button then use the up and down buttons (2 and 3) to increase or decrease the heating level.
- TIMER BUTTON: Use to set the timer from 0H– 24H (0-24 hours). Adjust using buttons 2 & 3 to the number of hours you would like to set.
Troubleshooting
- Check if the power cord is plugged into an electrical outlet.
- Error code shows on the display.
- E1: When the heater reaches 185 F(85°C ) or above, it will shut off. Allow the heater to cool down for 15 minutes, and restart the heater by pressing the Power button on remote control.
- E2: Error on Display: The heater has a tilt protection function. When the heater’s working angle exceeds 60° it automatically stops working. Change the working angle and manually press the power button, then the remote control function will be reactivated.
L1,2 shows in the display, but no heat: Bulb is damaged. So Call Customer Service (see the back side page).
MAINTENANCE INSTRUCTIONS
CLEANING AND MAINTENANCE
Regular and careful cleaning helps your far infrared heater operate
efficiently for many trouble-free years. To clean your heater, follow the
steps below.Unplug the power cord for your safety before cleaning your
appliance.
- Make sure the heater is cool before cleaning.
- To keep the heater clean, the outer shell maybe cleaned with a soft, damp cloth. You may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth. ( CAUTION: DO NOT wet the heater.)
- DO NOT use alcohol, gasoline, abrasive powders, furniture polish or rough brushes to clean the heater. This may cause damage or deterioration to the surface of the heater.
- DO NOT immerse the heater in water.
- Wait until the heater is completely dry before use.
- All maintenance must be performed by certified electrician.
Storage: Store the heater in a cool, dry location when not in use to prevent dust and dirt build up. Use packaging carton to store.
Safety precautions
- Read this “Safety precautions” carefully before using, and use it correctly.
- The precautions shown here are for safe and correct use of the products, in order to prevent harm, damages or injuries. Also, in order to clarify the magnitude of harm and damage and the extent of urgency, the precautions are categorized as “warming” and “caution”, which are matters likely to occur when handling incorrectly. Since both are important contents concerning safety. Make sure to comply with them.
“Scan here for more information of Infared Graphite Heater’
Product of SENGOKU L.A.. LTD.
3870 Del Amo Bivd., Ste. 505
Torrance, CA 90503
www.sengokula.com
Customer Service Line: 1-877-GET-HEAT
(877-438-4328)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>