Coolmetech Stage SinFree Karaoke Microphone System User Guide

Coolmetech Stage SinFree Karaoke Microphone System

Product Information

This is a multi-lingual quick start guide for the product. It contains instructions in English, Portuguese, German, and Japanese. The guide is numbered from 1 to 29 and may contain information on product setup, installation, and usage.

Product Usage Instructions

1. Before using the product, make sure to read the entire quick start guide.
2. Choose the language you prefer and locate the corresponding page number.
3. Follow the instructions provided on that page carefully.
4. If you encounter any difficulties during setup or usage, refer to the troubleshooting section of the guide.
5. Once you have successfully set up and installed the product, refer to the usage section of the guide for information on how to operate the product.
6. Always follow safety precautions while using the product.
7. Keep the quick start guide in a safe place for future reference.

DIAGRAM

1. RGBLights
2. VOL+Button
3. Power ON/OFF; Music/ Mic Volume Switch Button
4. VOL- Button
5. Sound Modes Button
6. Voice Cancelling / Back Button
7. Bluetooth / TWS Button
8. 3.5mm Headphones Port
9. 3.5mm Aux-in Port
10. Type-C Charging Port
11. Lighting Switch Button
12. Type-C Charging Cable
13. 3.5mm Aux Cable

MAIN FUNCTION

1. Bluetooth speaker for audio output.
2. Karaoke singing & voice recording.
3. Bedside lamp for sleeping atmosphere.

CHARGING

NOTE:

1. The microphone will prompt “battery low” every 5 minutes once the battery is under 10%.The lighting will be flashed in red at the same time.
2. Do not charge in a sub-zero environment, charging below zero may cause damage to the battery.
3. Do not use the microphone while charging, the output power is lower than normal working status.
4. When the battery is under 30%, the power of microphone will be automatically reduced to protect the battery, and avoid voice distortion

OPERATING INSTRUCTION

NOTE:

1. Please short-press the power button to select music volume or microphone volume, then press the volume +/- button to adjust the volume.
2. There are 4 sound effects on the microphone: Karaoke, Professional, Speech, and Original Sound. Karaoke is the default effect.
3. There are 4 LED lighting can be switched: Dynamic, Breathing Dynamic, RGB, and Single.

**AUX MODE

**

How It works:

1. Insert the AUX cable and 3.5mm headphones to connect Stage Sing Free with your device.
2. Power on the microphone.
3. Turn on the karaoke/music applications on your device and start your singing or recording

NOTE:

1. The AUX Mode is for voice recording and supports original sound effect only.
2. The audio won’t play through the microphone, please insert the 3.5mm headphones as well.
3. Unplug the AUX cable, the microphone will change to Bluetooth Mode automatically.

BLUETOOTH MODE

How it works:

1. Power on the microphone.
2. Search “Stage SingFree” from your device and click to connect.
3. Tum on the karaoke/ music applications on your device and start your singing.

NOTE:

1. How to use duet function between two Stage SingFree:
2. Connect the first Stage Sing Free as above, then power on the second Stage SingFree.
3. Long press the Bluetooth button of two microphones for 3s simultaneously to get into the TWS/duet mode. Release your finger after hearing the prompt.
4. Two microphones are connected to each other now. (The microphone connected to your device is the master one.)
5. In TWS mode, tum off one microphone, and the other one will shut down automatically. Two microphones connected before will connect together again after tu ming them on.
6. If there is no signal input for 20 minutes, the microphone will shut down automatically.

HEADPHONE MODE

How It works:

1. Power on the microphone and connect it with your device via Bluetooth.
2. Insert the 3.5mm headphones to the headphones port.
3. Tum on the karaoke/ music applications on your device and start your singing or recording.

NOTE:

1. The Headphone Mode only supports original sound effects.
2. The audio and your singing will play through the headphones instead of the microphone in this mode. Enjoy your private singing time.

FM / PARTY MODE

How It works:

1. Power on the microphone.
2. Long press the “M” button for 2 seconds to tum on the FM transmitter, and the microphone will broadcast the current frequency.
3. Repeat ‘Step 2’ to switch the frequency of the microphone, or adjust the frequency on your device/car to match the microphone’s.

NOTE:

1. There are 3 FM frequencies to choose from: 87.9MHz, 88.5MHz, and 89.7MHz.
2. Make sure the FM frequencies are the same as your devices (Car FM or other radio products), one frequency is allowed to match at a time.
3. Within 6 meters, one single Stage SingFree microphone can connect simultaneously with multiple devices at the same frequency to form party mode.
4. Within 6 meters, two Stage SingFree microphones can connect to each other via Bluetooth to form party mode.

SPECIFICATION

For more latest products, please visit:
www.coolmetech.com
For any assistance, please Email us:
service@coolmetech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>