ECO-WORTHY DUAL-AXIS Tracking System with Solar Tracker User Manual

June 11, 2024
ECO-WORTHY

DUAL-AXIS Tracking System with Solar Tracker
User Manual

Safety Caution

PLEASE READ CAREFULLY BEFORE PROCEEDING
The user should read and follow the manufacturer’s instructions for  ach component of the system. These instructions should be provided to the user of this equipment. The user should understand these instructions before using this equipment. The manufacturer’s instructions should be followed for the proper use and maintenance of this equipment.

  • Make sure that the surface has the strength to handle the weight of both solar panels and this bracket.
  • Use bolts, nuts, and gasket to make the solar panels and brackets firmly connected
  • Always loosen the corresponding screw before adjusting the angle or direction of solar panels. Never force this adjustment when the screw is still tightened.
  • Some components may deteriorate over extended periods of time due to wear or corrosion. For safety, the system should be checked regularly

Product Overview

ECO-WORTHY dual-axis solar tracker is perfect for mount of 4-6 pieces solar panels, it can make the panels face to the sunlight for more irradiance absorption and electricity generation. With the  attached controller, you can manually change the angel anytime. The package includes:

Main pole White rods
Mounting rods Drive rods
Controller Sunshine sensor
Air speed sensor Nuts and bolts

Components Description

Image Model Quantity
Main pole A 1

White rod B

|

1

| White rod C| 1
| White rod D| 1
| White rod E| 2
| Long u-type connector| 2

| Mounting rod G| 8
| Short u-type connector| 8
| M1490 Latch| 1
| M10
50 Latch| 2
| M1020 Screw| 8
---|---|---
| M8
90 Screw| 3
| M10100 Screw| 4
| M8
20 Screw| 8
| M1060 Screw| 16
| M10
40 Screw| 1
| M612 Screw| 2
| M4
16 Screw| 4
| Expanding screw M10*8| 8
| Drive rods base| 4
| Middle clamp| 6
| Side clamp| 12
---|---|---
| Short drive rod set| 1
| Short drive rod set| 1
| Controller| 1
| Sunshine sensor| 1
| Sunshine sensor base| 1
| Air speed sensor| 1

Installation Guide

OvervieECO-WORTHY DUAL-AXIS Tracking System with Solar Tracker -
Overview Place the main pole
There are four marks (S,N,W,E) on the pole’s each side. When place the main pole, the marks should face the exact directions of your house or yard. After choosing a position  for it, drill the pole into ground or some surface, remember the surface should strong enough to hold the weight of tracker and panels.Use an impact drill to drill a  hole with a diameter of 12mm and a depth of 55mm in the marked position. After drilling the hole on surface, use the M10x60 expansion screw to firmly fix the pole.ECO-WORTHY DUAL-AXIS
Tracking System with Solar Tracker - Place the main pol Put on the white rods

ECO-WORTHY DUAL-AXIS Tracking System with Solar Tracker - Put on the white
rods

First, use the M1490 latch in package to fix the B rod onto the main pole| Put the C rod on B rod with M1050 latches
ECO-WORTHY DUAL-AXIS Tracking System with Solar Tracker - Put on the white
rods

Use 3 of M890 screws to fix D rod on B rod side, the angle between D and B rods should be 90°| Use M10100 screws to fix the E-1, E-2 rods on C rod

Install the drive rods
Use M820 screws to fix one small base onto the “S” side of main rod. Do the same to the downside of B rod Put the short drive rod on the two bases, the head on the main rod one. Use the latches inside drive rod package to fix them. Same way to fix the long drive rod on between E-2 rod and D rod
Put on the mounting rodsECO-WORTHY DUAL-AXIS Tracking System with Solar
Tracker - Put on the mounting rods Put on the cross rods G-3 and G-4 on E-2 rod with M10
60 screws(for firmly holding the panels, the screw should be put into the second hole of G-1, G-2 rod). Same way to fix G-1, G-2 rods on E-1 rod
Use M1060 screw to fix F-1 rod vertically on C rod. Do the same to F-2 rod Fix the 2 of left G-8 rods with long u-type connector, this will use 4 of M1020 screws, same way to fix the other 2 G-8 rods on the right side.
As for the four connecting sections of other rods, use the short u-type connector and M10*60 screws to fix them.
Wire connection
Use screwdriver to loose and open controller’s cover. Inside, there is one circuit board
Connect the drive rods cable to its ports. Short drive rod cable to the third port, red cable to the left terminal, black cable to the right terminal. Long drive rod cable to the fifth port, same way to connect the terminals. The second port is for air speed sensor, there is marks on the cable, wire “G” cable into “G” terminal, and “IN” cable into the “IN” terminal. To operate the whole tracker, the controller should be connected with one 12V battery. Wire the battery cable into the fourth port, so that all connections get accomplished Put on the cover again by screwing those four sides screws.ECO-
WORTHY DUAL-AXIS Tracking System with Solar Tracker - Wire
connection Install controller & sensors
The controller should be put on the “E” side on the main pole, use suitable screw to fix it. The sunshine sensor needs to be put on the mounting rod. To make it sense the sunlight when sunrise, it should be fixed on the top right corner of the brackets. There is one clamp set for putting it on, just use screwdriver to tied it The air speed sensor needs to be put on somewhere with good ventilation, to sense the wind without any block Mount the solar panels ECO-WORTHY DUAL-AXIS Tracking System with Solar Tracker - Mount the solar
panels

Use the clamps in package to set panels on the whole bracket, double-head middle clamp  to put in  the middle of  two panels, the one  side clamp to fix one panel’s side. Use  the hexagonal screwdriver to make them tightened
The cross rods could hold maximum of 4*200w panels The vertical rods could hold 2 panels, one on the upside, the other on the downside. Each panel should be put on its side when installation Cross rod length: 114.2in(2900mm) width:29.4in(1000mm) Vertical rod length(each side): 45.6in(1160mm) width:30.3in(770mm)![ECO-WORTHY DUAL-AXIS Tracking System with Solar Tracker

Support

For the use of this manual and the conditions or methods of installation, operation, use, and maintenance of product are beyond ECO-WOR- THY’s control, ECO-WORTHY does not accept responsibility and expressly disclaims liability for any loss, damage, or expense arising out of or in any way connected with such installation, operation, use or maintenance.
No responsibility is assumed by ECO-WORTHY for any infringement of patents or other rights of third parties, which may result from the use of the product. No license is granted by implication or otherwise under any patent or patent rights. The information in this manual is based on ECO-WORTHY’s knowledge and experience and is believed to be reliable, but such information including product specification (without limitations) and suggestions do not constitute a warranty, expresses or implied.
ECO-WORTHY reserves the right to change the manual, the PV products, the specifications, or product information sheets without prior notice.
This product is covered by a 1 year warranty provided by ECO-WORTHY Ltd. We will refund or partial  refund or replace any products with defects due to our imprudence.
If you are experiencing technical problems and cannot find a solution in this manual, please contact ECO-WORTHY for further assistance.

Contact number:
US 1-866-939-8222
UK +44 20 7570 0328
Email: customer.service@eco-worthy.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals