ECO-WORTHY Adjustable Multi-Piece Solar Panel Mounting Brackets User Manual
- June 9, 2024
- ECO-WORTHY
Table of Contents
ECO-WORTHY Adjustable Multi-Piece Solar Panel Mounting Brackets
Notice
- Please wear gloves before installation to prevent hand injuries！
- To avoid a shock hazard, keep the panel covered with a dark material during installation and avoid contact with the output terminals.
- If the panels will be mounted on a roof, make sure the material is strong enough to provide support to the solar panel including wind loading.
- To minimize wind loading effects in an RV or mobile application, place the panel’s longest edge parallel with the direction of wind travel.
- If you want to place the bracket on the ground, please choose a flat, hard surface, use self-tapping screws for installation with the plane, or choose a heavy thing to press the bracket.
Components&Accessories
(Some components already pre-installed)
Installation
- Step.1 Set the four feet
Put those four pre-installed base feet on the ground or surface where you want to install the brackets.
- Step.2 Mount the vertical rods
- Use screws to fix the two vertical rods on the feet, and if you want to change the tilt angel, you could drill the upper screw into the different holes on the rod, it’s able to set the angel degree as 30, 35, 40, 45 by diverse setting holes, The order be, top hole-30, second-35, third-40, fourth-45. You could choose the proper angle according to your location and latitude, E.g. If you live in California, set the vertical rods at 35°hole.
- So that the panels can get the maximum solar irradiance.
- After the top holes get settled, use other screws to fix the rod with rest holes on the feet, and do the same to the other vertical rod.
- Step.3 Connect horizontal rods
Use the 2 connectors in the package to separately connect the 4 horizontal rods, each connector for one pair. There are drilled screws on the connectors, you need to screw them out, position the rod hole with the connector hole, then put the screw in again. One rod mounting get accomplished when the connector’s 2 sides be fixed with 2 rods. Do the same to the other connector.
- Step.4 Put the horizontal rods on
- Use inside bolts to connect the horizontal rods with the vertical ones, pay attention to the red marks on the horizontal rods, it’s the best setting position for keeping the weight balance.
- After point on the two sides’ marks with one rod, use the screw to make them tied together. Do the same to the other rod.
- Step.5 Drill the feet into the surface
- When all rods get mounted, place the position on ground or flat surface that needs to be fixed and make a hole mark for the base feet fixing. In case of heavy wind or storm, If there is no solid surface, you can place a cement block for the drilling, or just put some heavy stuff to cover the feet.
- Remember to put the brackets towards the south side, it’s the best direction to absorb the sunlight in the north hemisphere.
- Then use an impact drill to drill a hole with a diameter of 12mm and a depth of 55mm in the marked position. After drilling the hole, use the M10x80 expansion screw to fix the feet firmly
- Step.6 Mount panels and clamps
Put the panels on the two horizontal rods, mount the clamps into the rods’ rail, and use the Y-shape sleeve to tie the screws on the clamp, so it’ll press the panels on the rods. Two-head clamp be put in between two panels, and side clamp to hold one panel’s side.
ABOUT COMPANY
- Tel：
- +44 20 7570 0328(EU)
- 1-866-939-8222(US)
- E-mail: customer.service@eco-worthy.com
- Web: www.eco-worthy.com
References
- Sell Diamonds, Jewelry and Watches for the Best Price | Worthy
- Eco-Worthy: Solar Panel Kits, Lithium Battery & DIY Solar Power System – ECO-WORTHY
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>