Irobot Braava Jet 240 Mop Owners Guide

Irobot Braava Jet 240 Mop Owners Guide

About your Braava jet™

Top View – Front

Bottom View

Using your Braava jet™

1. Charge & Insert the Battery

   • Place the battery into the battery charger and plug the charger into an electrical outlet.
   • The indicator light will blink amber while the battery is charging. The light will switch to solid green when the battery is fully charged.
   • The wall charger automatically goes into a low-power mode when the battery is fully charged to maintain the life of the battery and limit power usage.
   • The battery will fully charge within 2 hours. Battery should always be charged for the full 2 hours in between every cleaning cycle for optimal performance.
   • Insert the fully charged battery into the robot.
   • iRobot also offers additional batteries and chargers as accessories for purchase, so you can always have a charged battery ready to go.

2. Select a Braava jet Cleaning Pad

   • Choose a cleaning pad that matches how you want to clean your floor. Refer to next page for details.
   • Your robot comes with a sample pack of Wet Mopping, Damp Sweeping, and Dry Sweeping Braava jet cleaning pads.
   • 2b Slide in a Cleaning Pad
   • Slide a Braava jet pad into the track on the bottom of the robot until it clicks into place.
   • You can attach a Braava jet pad from either side of the robot.
   • Braava jet will automatically recognize the pad and adjust its cleaning behavior based on the pad you choose.
     Cleaning Tip: Before using a Wet Mopping or Damp Sweeping pad, use a Dry Sweeping pad or vacuum to clean loose debris.
     Braava jet™ Cleaning Pad Information
     RECOMMENDED FOR

3. Fill the Robot with Water

   • Fill the robot with water if you choose Wet Mop or Damp Sweep.

   • Lift the robot handle to find the tank cap and lift and swivel it open.

   • To help allow the tank to fill completely, tilt the robot so that the front left corner is pointed downward and the tank opening is highest. Fill slowly with warm water.

   • Turn the cap back and close. Lower the robot handle before starting
     the robot.

   • Do not use any other cleaning solution with your robot other than water.
     Note: If you are using a Dry Sweeping Pad, skip to Step 4.

4. Just Press CLEAN

   • Place your robot in the lower left corner of the area you want to clean, about a foot away from any walls.
   • Press CLEAN once to wake up the robot. Press CLEAN again to start the cleaning cycle.
   • The robot will clean rooms up to 200 ft2 (20 m2) while mopping, and rooms up to 250 ft2 (25 m2) while damp or dry sweeping.*
   • Braava jet will finish by cleaning the edges and perimeters of your room, furniture, and fixtures.
     Note: When it has
     finished cleaning, Braava jet returns to where it started, powers off and plays a tone.

5. Eject the Cleaning Pad and Prepare Braava jet™ for Next Use

   • To eject the cleaning pad without touching the dirt, lift the handle and pull back on the Pad Eject Button.
   • Remove the battery and put it in the charger so it can charge for the next cleaning.
   • Empty the water tank before storing the robot.
   • Braava jet can be stored wheels-down or on its side with the battery side down.

6. Download the iRobot® HOME App
   Gain access to exclusive features, software updates, and supporting information.

How Braava jet™ Navigates

Braava jet is designed to intelligently navigate and clean rooms up to 200 ft2 (20 m2) while wet mopping and up to 250 ft2 (25 m2) while damp and dry sweeping.*

• The robot starts by cleaning to the right until it encounters a wall or other barrier.
• When wet mopping or damp sweeping, Braava jet repeats the first line twice to achieve the optimal wetness of the pad before it cleans the rest of the room.
• When the robot has cleaned as far as it can to the right, the robot will continue to the area in front and to the right of where it started.
• The robot will stop cleaning and will return to where it started when the cleaning job is done.
• Braava jet does not spray furniture or walls. Before the robot sprays, it will back up to ensure it’s only spraying a portion of the floor it knows is clear. Lift up floor-length curtains before running Braava jet.
• As Braava jet finds edges, chair legs, and other obstacles, it will clean around them and then return to its original path and resume cleaning.
• Braava jet creates a new map every time it cleans.

Using Virtual Wall® Mode
You can create an invisible barrier with the Virtual Wall® Mode so that the robot will avoid cleaning part of a room or a different floor type.

• Begin with the robot powered off. When placing the robot, note that the invisible line will be created in line with the back of the robot.

• To activate Virtual Wall Mode, start with a powered-off robot and press and hold the CLEAN button until two blue lines appear on the top of the robot. The blue lines will indicate that the Virtual Wall Mode has been activated.
  Cleaning Tip: You can also use Virtual Wall Mode to divide a larger room into smaller areas to help Braava jet clean more efficiently.

• Once in Virtual Wall Mode, the robot will mark an invisible boundary in its internal map, extending out to each side (see illustration). As the robot cleans your floor, it will not go beyond the invisible line.

• Once the robot is in place, just press CLEAN to start the job.

• Virtual Wall Mode will turn off automatically when the robot completes its job. To manually clear a Virtual Wall Mode cleaning cycle and turn off the robot, press and hold the CLEAN button until all indicators turn off.

Tips for Best Performance

• For best results, use a Dry Sweeping Pad or vacuum to pick up dirt and dust before running your robot with a Wet Mopping or Damp Sweeping Pad.
• Do not presoak cleaning pads before attaching them to the robot. Pads should be dry at the start of a cleaning cycle.
• To pause your robot during a cleaning cycle, press the CLEAN button. To resume the cleaning cycle, press the CLEAN button again. Do not pick up and move your robot while it is cleaning – the robot will end its cleaning run if you do.
• To turn off your Braava jet, press and hold the CLEAN button for 5 seconds.
• Tilt robot slightly when filling to ensure tank fills completely.
• Only use water inside your robot. Cleaning solutions, even natural ones, can clog the spray nozzle and break down the materials inside the robot.
• Your robot will only run with Braava jet Pads, which are specifically made for the robot.
• Braava jet cleans best on smooth hard surfaces and may not perform as well on uneven tiles, heavily waxed floors or rough surfaces like slate or brick which may snag the cleaning pads.
• Lift up floor-length curtains before running the Braava jet.

Troubleshooting

Braava jet will tell you something is wrong by alerting you with sounds and lights. If the problem is not resolved, learn more online at www.irobot.com/support or contact Customer Care at 877-855-8593.

Repeating Error Messages
If your robot remains on after an error occurs, press the bumper toward the body of the robot once to repeat the message. If your robot has turned off after an error occurs, press CLEAN to turn it on. If the error is ongoing, the robot will repeat the message. Visit www.irobot.com/support to view
a complete error table.

Rebooting Instructions
For some errors, rebooting the Braava jet may resolve the problem. To reboot Braava jet, press and hold CLEAN for 5 seconds until you hear an audible tone. Take out the battery and insert it again. Press CLEAN again to turn the robot back on.

Precision Jet Spray Troubleshooting
If the robot is not spraying or is spraying unevenly and you have checked that the tank has enough water and can hear the pump running, contact Customer Care at 877-855-8593.

Water Level Troubleshooting
If you encounter problems with the amount of water Braava jet uses on your floors in wet mopping or damp sweeping modes, download the iRobot® HOME App to adjust your robot’s settings.

Regular Robot Care

Follow these tips to keep your iRobot Braava jet running at peak performance. See the About your Braava jet™ section for reference, as needed.

Cleaning the Cliff Sensors and Pad Reader
Clean the sensors on the bottom of your robot with a damp cloth.

Cleaning the Wheels
Pull off any visible debris or hair that gathers around the wheels.

Cleaning the Body of the Robot
Use a damp cloth to lightly wipe off any dirt on its body or bumper.

Cleaning the Precision Jet Spray Nozzle
Wipe clean with a damp cloth.

Cleaning the Tank
If you notice an odor in the tank, fill the tank with hot tap water. Do not use boiling water. Close the cap and lightly shake the robot. Rinse the tank and repeat. Allow the tank to dry with the cap open before using your robot.

Caring for Washable Cleaning Pads
Braava jet Washable pads can be washed up to 50 times* before replacing. Hand washing and air drying is recommended. If using a washing machine, wash using the warm cycle and air dry. Do not wash with delicates.

Customer Care Contact Information
USA & Canada:
Phone: 877-855-8593
Website: www.irobot.com/support
Outside USA & Canada:
Website: global.irobot.com
©2016-2017 iRobot Corporation, 8 Crosby Drive, Bedford, MA 01730 USA. All rights reserved. iRobot and Virtual Wall are registered trademarks of iRobot Corporation. Braava jet is a trademark of iRobot Corporation. App Store is a trademark of Apple, Inc., registered in the U.S. and other countries. Google Play is a trademark of Google, Inc.
WC: 4491844 v3

Download PDF:Irobot Braava Jet 240 Mop Owners Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>