Philips GC4567/80 Azur Grey Steam Iron User Manual
- June 11, 2024
- Philips
Table of Contents
Philips GC4567/80 Azur Grey Steam Iron
What’s In the Box
Precautions
- Always ensure that the iron is properly assembled and the cord is not frayed or damaged before use.
- Always unplug the iron before filling the water tank or when not in use.
- Do not touch the soleplate of the iron when it is hot as it can cause burns. Let it cool down before handling it.
- Do not use the iron near water or immerse it in water.
- Do not use the iron to iron clothes or fabrics that are not suitable for ironing.
- Do not leave the iron unattended while it is plugged in or switched on.
Preparing for Use
Smoke can be visible during the First use, and it is normal. This ceases after a short while.
How to Use
- Fill the water tank with water up to the maximum level. Use distilled water or a mixture of distilled and tap water to prevent mineral buildup.
- Plug in the iron and select the appropriate temperature setting for the fabric you will be ironing. The iron will heat up and the temperature indicator light will turn off when it is ready to use.
- Hold the iron upright and press the steam button to release the steam. The steam boost function provides an extra burst of steam for stubborn wrinkles.
- Place the item to be ironed on the ironing board and smooth it out. For best results, start with the areas that require the lowest temperature and work your way up to the highest temperature.
- Glide the iron over the fabric in a smooth, continuous motion, pressing down gently. For tough wrinkles, hold the iron in place for a few seconds.
- To use the vertical steam function, hold the iron upright and direct the steam towards the fabric, but be sure to avoid getting too close to the fabric to prevent damage.
- When finished, unplug the iron and allow it to cool down before storing it.
Auto Shut off
Safety Instructions
CALC Clean
- Ensure the iron is unplugged and cooled down before performing Calc Clean.
- Fill the water tank with water up to the maximum level and set the temperature to the maximum setting.
- Place a container under the steam vents to collect any water and debris that may be expelled during the Calc Clean process.
- Hold the Calc Clean button on the iron for about two seconds, and then release it. The Calc Clean light will start blinking, indicating that the Calc Clean process has started.
- Once the Calc Clean light stops blinking, hold the iron over the container and press the Calc Clean button again to expel any remaining water and debris.
- Finally, refill the water tank with clean water and rinse the iron by pressing the steam button a few times over a sink or container.
- Once done, plug the iron back in and allow it to heat up before using it again.
- If the Calc Clean function does not completely remove the buildup, repeat the process a few times or use a descaling solution to clean the iron.
- After performing the Calc Clean function, always empty the water tank and allow the iron to cool down before storing it.
- When using iron, always use distilled water or a mixture of distilled and tap water to prevent mineral buildup.
FAQ’s
How do I fill the water tank of the Philips GC4567/80 Azur Grey Steam Iron?
To fill the water tank, open the lid and pour water into the opening until it reaches the maximum level indicated on the tank.
Can I use tap water in the Philips GC4567/80 Azur Grey Steam Iron?
It is recommended to use distilled water or a mixture of distilled and tap water to prevent mineral buildup in the iron.
How do I select the appropriate temperature setting for the fabric I will be ironing?
Refer to the care label on the fabric and select the temperature setting accordingly. The iron has a temperature dial that can be adjusted to the desired temperature.
How do I use the steam function of the Philips GC4567/80 Azur Grey Steam Iron?
Hold the iron upright and press the steam button to release steam. The steam boost function provides an extra burst of steam for tough wrinkles.
How do I use the vertical steam function of the Philips GC4567/80 Azur Grey Steam Iron?
Hold the iron upright and direct the steam towards the fabric. Be sure to avoid getting too close to the fabric to prevent damage.
How often should I perform the Calc Clean function on the Philips GC4567/80 Azur Grey Steam Iron?
It is recommended to perform the Calc Clean function at least once a month to prevent mineral buildup and ensure optimal performance.
How do I know when the iron is ready to use?
The temperature indicator light on the iron will turn off when it is ready to use.
Can I use the Philips GC4567/80 Azur Grey Steam Iron on delicate fabrics?
Yes, the iron has a low temperature setting that can be used for delicate fabrics.
Can I use the Philips GC4567/80 Azur Grey Steam Iron to iron clothes that are already dry?
Yes, the iron can be used to iron clothes that are already dry.
How do I store the Philips GC4567/80 Azur Grey Steam Iron?
Unplug the iron and allow it to cool down before storing it. Always empty the water tank to prevent mineral buildup.
How do I clean the soleplate of the Philips GC4567/80 Azur Grey Steam Iron?
Allow the iron to cool down, then wipe the soleplate with a damp cloth. For tough stains, you can use a cloth dampened with a small amount of vinegar.
Can I use the Philips GC4567/80 Azur Grey Steam Iron without steam?
Yes, you can use the iron without steam by simply not pressing the steam button.
Download The PDF Link:Philips GC456780 Azur Grey Steam Iron User Manual