Broan-NuTone SENSonic Voice Voice Control Fan Light Speaker Instructions

SENSONIC VOICE™ Voice Control

Fan/Light/Speaker Installation Instructions

READ AND SAVE THESE INSTRUCTIONS

For Warranty Statement, Service Parts, Technical Support, or to Register your product, please visit our website or call:
In the United States – broan-nutone.com 800-558-1711.
In Canada – broan-nutone.ca 800-567-3855

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Acceptable for use over a tub or shower when connected to a GFCI (Ground Fault Circuit Interrupter) – protected branch circuit (ceiling installation only).
8. This unit must be grounded.
9. If you’ve never installed electrical appliances that require wiring, you may need assistance from someone with more experience.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. This product can be installed in a wall if mounted 8-ft. or more above the floor.
3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.
4. Please read specification label on product for further information and requirements.

CLEANING & MAINTENANCE

For quiet and efficient operation, long life, and attractive appearance – lower or remove grille and vacuum interior of unit with the dusting brush attachment. The motor is permanently lubricated and never needs oiling. If the motor bearings are making excessive or unusual noises, replace the blower assembly (includes motor and impeller).

OPERATION

The Voice Controlled Fan/Light/Speaker must be operated using only the wall control included. See separate operating instructions. DO NOT operate the Voice Controlled Fan/Light/Speaker with any other switches or controls.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks by Broan-NuTone LLC is under license. Other trademark and trade names are those of their respective owners. The APPLE logo and APP STORE are trademarks of Apple Inc., registered in the United States and other countries and regions. App store is a service mark of Apple Inc. Google Play and the Google Play logo are trademarks of Google LLC. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules and RSS-210 of Canada. Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC IDs: 2ADLL-1108935 & 2ADLL-1109038 IC : 2143B-1108935 & 2143B-1109038
This Bluetooth® wireless technology enabled luminaire complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying exposure compliance. This luminaire must not be co-located or operate in conjunction with any other antenna or transmitter.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

1. COOKING AREA
   Do not install above or inside this area.

2. NOT FOR USE IN A COOKING AREA.

3. Cooking Equipment

4. Floor

IMPORTANT – The ducting from this fan to the outside of the building has a strong effect on the air fl ow, noise and energy use of the fan. Use the shortest, straightest duct routing possible for best performance, and avoid installing the fan with smaller ducts than recommended. Insulation around the ducts can reduce energy loss and inhibit mold growth. Fans installed with existing ducts may not achieve their rated airflow.

1. POWER CABLE *

2. FAN HOUSING

3. INSULATION
   (Place around and over fan housing.)

4. ROOF CAP* (with built-in damper)

5. Keep duct runs short.

6. WALL CAP*
   (with built-in damper)

7. 4-IN. ROUND ELBOWS*

8. Seal duct joints with tape.

9. 4-IN. ROUND DUCT*

10. Seal gaps around housing.

• Purchase separately

OPTION – To mount housing anywhere between ceiling framing:
Use optional Hanger Bar Kit (sold separately from local distributors or website). Follow mounting instructions included with kit.

ALL INSTALLATIONS

[1] Remove all packing material, unplug and remove blower from fan housing.

[2] Remove wiring panel from fan housing (if already installed).

[3] A pair of flanges may be attached to housing if desired or required.

Snap both flange pieces under rolled-over edge of housing (all four sides).

For Retrofit Installation – Skip to Page 3.

NEW INSTALLATION

[4] Attach damper/duct connector to fan housing.

Push connector through opening from inside of housing.
Engage tabs and secure with screw from parts bag.

1. TABS

[5] Mount housing to ceiling structure.

Make sure bottom of housing will be flush with finished ceiling.
For proper location using 1/2″ ceiling material: Bend out housing tabs (on outside of housing) to fit against bottom of joist.
Secure housing through mounting ears with appropriate fasteners. If mounting housing to I-joist, use wood blocking as shown.

1. I-JOIST
2. WOOD BLOCKING
3. HOUSING TABS

[6] Connect 4-in. round duct.

[7] Connect wiring.

Connect power cable that will supply constant 120V AC to unit. Attach wiring to wiring plate (from parts bag) using UL approved connector. Connect house wiring to fan wiring – black to black, white to white, and green to green or bare wire. Use screw (from parts bag) to secure wiring plate to fan housing. Re-install wiring panel and secure with screw from parts bag. See wiring diagram on page 4.

[8] Finish ceiling.

Then continue with Step 9.

RETROFIT INSTALLATION

[4] Remove old fan and prepare ceiling.

Enlarge ceiling opening (if necessary) to 9 ¾” (parallel to joist) by 10 ½” (perpendicular to joist). (Some models have a cut-out template on side of carton.)

Existing fan housings are typically attached to the structure:

• with screws, nails, or staples, which must be removed.
• with hangers or rails which are fastened to joists and must be removed along with housing.

A pry bar may be needed to remove the old housing. Leave ductwork and wiring in place.

a) JOIST

[5] Fold mounting ears flat against housing.

[6] Connect wiring.

Connect power cable that will supply  constant 120 VAC to unit. Attach wiring to wiring plate (from parts bag) using UL approved connector. Connect house wiring to fan wiring – black to black, white to white, and green to green or bare wire. Use screw (from parts bag) to secure wiring plate to fan housing. Re-install wiring panel and secure with screw from parts bag. See wiring diagram on page 4.

[7] Mount fan to ceiling structure.

Mount housing to ceiling structure with appropriate fasteners in locations shown.

• Center hole is optional.

[8] Connect 4-in. round duct.

(1) Pull existing ducting through housing discharge opening and (2) tape ducting to duct connector. (3) Push connector/ducting back through opening. Engage tabs and (4) secure with screw from parts bag.

a) TABS

Continue with Step 9.

ALL INSTALLATIONS

[9] Install blower.

Re-install blower removed in Step 1. Secure blower with 2 screws from parts bag. Plug blower into black receptacle.

[10] Install grille.

Connect plug from grille to wire panel. Squeeze grille springs and insert into slots in blower. Push grille up against ceiling.

1. If grille spring becomes dislodged from grille – snap it back into place as shown.

[11] Install wall control.

Note: Location of wall control must be within 20 feet (not obstructed) of grille.
Use one of two methods to attach control:
(1) Mount control to new single-gang electrical box. (Recommended method.)
(2) Mount control to wall with clearance hole in wall.
Note: When replacing an existing switch with the new wireless wall control, care must be taken to properly terminate the existing wiring in a method approved by local building codes. If you are unsure, contact a qualified person.
Remove control module, install 2-AAA batteries, and replace module.
Snap control cover in place. Note: Metallic cover plates are not recommended.
To pair the wall control, turn on power to voice controlled fan and (within 3 minutes) press and hold the mute button icon on wall control for at least 5 seconds.
The light on the fan will fl ash when paired.

• If installing more than 1 Sensonic Voice fan in your house, only the fan that you are attempting to pair with a wall control should be powered. All other Sensonic Voice fans in your house should not be powered to prevent the wall control from pairing to multiple fans.

a) Note orientation of tab and buttons.
b) MUTE BUTTON

[12] Download the VoiceControl app.

Download the VoiceControl app from the Apple App Store or on Google Play. Set the device name in the app.

[13] Additional information.

For additional information please view:
the Best Practices Guide or the FAQs.

WIRING DIAGRAM

  BLACK
    WHITE
    GROUND (bare/green)

1. RECEPTACLE
   (LIGHT)

2. RECEPTACLE
   (FAN)

3. WIRING PLATE

4. 120 VAC LINE IN

1108938C

References

• . Spend less. Smile more.
• Broan-NuTone | Better Air. Better Life.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>