SONY KLV-S15G10 Flat Panel LCD Television User Guide
- June 11, 2024
- Sony
Table of Contents
KLV-S15G10
KLV-S20G10
Quick Setup Guide
Please follow the steps to setup your TV:
Checking the Supplied Accessories
- Remote control (RM-Y1104) (1) and size AA batteries (2)
- 75-ohm coaxial cable (ferrite core attached) (1)
- AC power cord (1)
- AC power adaptor (1) (KLV-S15G10 only)
- VESA adaptor: bracket A (1), bracket B (1) and screws (2) (KLV-S15G10 only)
- Operating Instructions
- Quick Setup Guide
- Leaflet (Installing the Wall-Mount Bracket to the TV, KLV-S20G10 only) (1)
- Warranty Card
Inserting Batteries into the Remote Control
Insert two size AA batteries (supplied) by matching the + and – on the
batteries to the diagram inside the remote control’s battery compartment.
Connecting Your TV
- Review the following chart to determine which diagram to use to connect the components in your system:
For these components | See reverse side |
---|---|
A | |
B | |
C |
- See the “Cables Required” chart that appears with the diagram to determine which cables you’ll need. You may need to purchase extra accessories, such as cables and splitters, depending on the components you plan to connect.
- Turn off and unplug all components before making connections.
- If you are connecting a digital cable box, you’ll need a special bidirectional splitter that’s compatible with your cable box. Contact your cable provider for details.
Making Video Connections
Your TV includes several types of video inputs. Use the inputs that are available on your components that provide the best video performance, as shown in the table on the right.
Connector type
| Component video*
| S VIDEO
| Composite video
| RF/Coaxial
Additional Connections
Depending on which components are in your system, you may need to complete
additional connections. For example, if you have a satellite receiver, you’ll
need to connect the satellite antenna. If you have an A/V receiver, you’ll
need to connect speakers.
Note
The connection diagrams shown on the reverse side are recommendations only;
other possible solutions may exist. Connections that include an A/V receiver
can often be very complex, so check your A/V receiver’s instruction manual for
additional details.
Running Initial Setup
-
Press POWER to turn on the TV.
The Initial Setup screen appears. -
Press or on the remote control to select the on-screen display language. Then press .
The message “First please connect cable/antenna” appears.
Note
By default, Auto Program is set to scan cable TV channels. -
Press CH+ to start Auto Program.
Auto Program automatically creates a list of receivable channels.
When finished, the lowest numbered channel is displayed. When all the
receivable channels are stored, the “Show/Hide Channels” menu appears.
To scan available VHF/UHF antenna channels instead of the cable
TV channels
- Press MENU, then go to Channels menu.
- Set Cable to Off.
- Start Auto Program by pressing .
To perform Auto Program again, follow the above instructions.
Depending on your signal source, be sure to set Cable to On or Off accordingly
(see Operating Instructions).
Note
The Initial Setup menu will appear each time the TV is turned on until you
complete the scanning for the available channels.
Programming the Remote Control
The remote control is preset to operate Sony brand video equipment.
Sony Equipment | Programmable Code Number |
---|---|
VCR/DVD | 301 (Sony VCR) |
SAT/CABLE | 801 (Sony Sattellite Receiver) |
Follow the steps below to program your TV’s remote control to operate non-Sony
video equipment.
Using the code list below, find the three-digit code number for the
manufacturer of your equipment. (If more than one code number is listed, use
the number listed first.)
- Press CODE SET.
- Press the FUNCTION button you want to program on the remote control. The selected FUNCTION button (VCR/DVD or SAT/CABLE) will flash.
- Enter the three-digit manufacturer’s code number using the 0–9 buttons while the button is lit (approximately 10 seconds).
- Press button.
When the programming is correct, the selected FUNCTION button will flash twice slowly, and when not, flashes five times quickly.
To check if the code works
Aim your TV’s remote control at the equipment, and press the VCR/DVD and/or
SAT/CABLE (POWER) button that corresponds with the equipment. If the equipment
responds, the programming is completed. If not, try the next code listed.
Notes
- If you enter a new code number, the code number you previously entered at that setting is erased.
- If no code is input within the above specified time, or an invalid or incorrect code number is input, the remote control automatically goes back to the previous setting.
- In some cases, you may not be able to program your remote control to operate other equipment. In such cases, use the equipment’s own remote control.
- Dead batteries or removing the batteries may cause the programmable codes to be lost and revert back to factory settings. Reprogramming the codes may be necessary.
Manufacturer’s Codes VCRs
Manufacturer | Code |
---|---|
Sony | 301, 302, 303, 348 |
Admiral (M. Ward) | 327 |
Aiwa * | 338, 344 |
Audio Dynamic | 314, 337 |
Broksonic | 319, 317 |
Canon | 309, 308 |
Citizen | 332 |
Craig | 302, 332 |
Criterion | 315 |
Curtis Mathes | 304, 338, 309 |
Daewoo | 341, 312, 309 |
DBX | 314, 336, 337 |
Dimensia | 304 |
Emerson | 319, 320, 316, 317, 318, 341 |
Fisher | 330, 335 |
Funai | 338 |
General Electric | 329, 304, 309 |
Go Video | 322, 339, 340 |
Goldstar | 332 |
Hitachi | 306, 304, 305, 338 |
Instant Replay | 309, 308 |
JC Penney | 309, 305, 304, 330, 314, 336, 337 |
JVC | 314, 336, 337, 345, |
346, 347
Kenwood| 314, 336, 332, 337
LXI (Sears)| 332, 305, 330, 335,
338
LG| 332
Magnavox| 308, 309, 310
Marantz| 314, 336, 337
Marta| 332
Memorex| 309, 335
Minolta| 305, 304
Mitsubishi/MGA| 323, 324, 325, 326
Multitech| 325, 338, 321
NEC| 314, 336, 337
Olympic| 309, 308
Optimus| 327
Panasonic| 308, 309, 306, 307
Pentax| 305, 304
Philco| 308, 309
Philips| 308, 309, 310
Pioneer| 308
Quasar| 308, 309, 306
RCA/PROSCAN| 304, 305, 308, 309, 311, 312, 313, 310, 329
Realistic| 309, 330, 328, 335,
324, 338
Sansui| 314
Samsung| 322, 313, 321
Sanyo| 330, 335
Scott| 312, 313, 321, 335, 323, 324, 325, 326
Sharp| 327, 328
Shintom| 315
Signature 2000
(M. Ward)| 338, 327
SV2000| 338
Sylvania| 308, 309, 338, 310
Symphonic| 338
Tashiro| 332
Tatung| 314, 336, 337
Teac| 314, 336, 338, 337
Technics| 309, 308
Toshiba| 312, 311
Wards| 327, 328, 335, 331,
332
Yamaha| 314, 330, 336, 337
Zenith| 331
DVD Players
Manufacturer | Code |
---|---|
Sony | 751 |
Panasonic | 753 |
Pioneer | 752 |
RCA | 755 |
Toshiba | 754 |
Cable Boxes
Manufacturer | Code |
---|---|
Sony | 230 |
Hamlin/Regal | 222, 223, 224, 225, 226 |
Jerrold/G. I./Motorola | 201, 202, 203, 204, 205, 206, 207, 208, 218 |
Oak | 227, 228, 229 |
Panasonic | 219, 220, 221 |
Pioneer | 214, 215 |
Scientific Atlanta | 209, 210, 211 |
Tocom | 216, 217 |
Zenith | 212, 213 |
Satellite Receivers
Manufacturer | Code |
---|---|
Sony | 801 |
General Electric | 802 |
Hitachi | 805 |
Hughes | 804 |
Panasonic | 803 |
RCA/PROSCAN | 802, 808 |
Toshiba | 806, 807 |
A (KLV-S15G10)
Use this diagram if you have;
Cables Required
Splitter| 1
Coaxial| 4
Composite| 2
If you are not using a cable box or satellite receiver, connect your cable or antenna to the VCR’s RF IN jack.
B (KLV-S15G10)
Use this diagram if you have;
Cables Required
Coaxial| 2
Composite| 1
Component| 1
Audio| 1
If you are not using a cable box or satellite receiver, connect your cable or antenna to the TV’s VHF/UHF jack.
C (KLV-S15G10)
Use this diagram if you have;
Cables Required
Splitter| 1
Coaxial| 4
Composite| 2
Component| 1
Audio| 1
If you are not using a cable box or satellite receiver, connect your cable or antenna to the VCR’s RF IN jack.
A (KLV-S20G10)
Use this diagram if you have;
Cables Required
Splitter| 1
Coaxial| 4
Composite| 2
If you are not using a cable box or satellite receiver, connect your cable or antenna to the VCR’s RF IN jack.
B (KLV-S20G10)
Use this diagram if you have;
Cables Required
Coaxial| 2
Composite| 1
Component| 1
Audio| 1
If you are not using a cable box or satellite receiver, connect your cable or antenna to the TV’s VHF/UHF jack.
C (KLV-S20G10)
Use this diagram if you have;
Cables Required
Splitter| 1
Coaxial| 4
Composite| 2
Component| 1
Audio| 1
If you are not using a cable box or satellite receiver, connect your cable or antenna to the VCR’s RF IN jack.
This file has been downloaded from:
www.UsersManualGuide.com
User Manual and User Guide for many equipments like mobile phones, photo
cameras, monther board, monitors, software, tv, dvd, and othes..
Manual users, user manuals, user guide manual, owners manual, instruction
manual, manual owner, manual owner’s, manual guide, manual operation,
operating manual, user’s manual, operating instructions, manual operators,
manual operator, manual product, documentation manual, user maintenance,
brochure, user reference, pdf manual
https://www.usersmanualguide.com/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>