centechia XW160 WIFI X10 Smart Doorbell User Manual

centechia XW160 WIFI X10 Smart Doorbell

Product Information

The product complies with Part 15 of the FCC Rules, which sets the standards for radio frequency devices in the United States. The device is designed to operate without causing harmful interference and must accept any interference received, including interference that may cause undesired operation.

Product Usage Instructions

Users must not make any changes or modifications to the device that are not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. To ensure proper operation of the device, users must adhere to the following two conditions:

1. The device must not cause harmful interference.
2. The device must accept any interference received, including interference that may cause undesired operation.

Failure to comply with these conditions may result in improper functioning of the device or potential harm to the user or others.

Product Introduction

Product Functions

• Visual call : When someone rings the doorbell, the mobile phone with the doorbell bound will receive a push notification from the APP, you can answer it by video call with visitors. Maximun Talking time 5 minutes.
• Real time picture: the device is connected to WiFi for a long time with low power consumption, you can wake it up remotely at any time, anywhere, and views the real-time picture. it is both a doorbell and also a monitor. This function is enabled by default.
• Power saving mode: when the doorbell is in the power saving mode, if there is no operation within 30 seconds, the doorbell will automatically turned off to save power.
• Purpose: To prolong the service time of the device. In this mode, real-time screen viewing is not available, and APP push will be delayed accordingly. When the battery power is lower than 10% (including 10%), the power saving mode will be forced on. Please Charge the device quickly. You can also actively turn off the real-time screen mode in the APP and switch to power saving mode.
• Night vision function: when the light is insufficient, the doorbell can automatically conduct infrared light compensation imaging. infrared light compensation function is on by default.
• It can be turned on and off in APP settings.
• Motion sensing: This product can detect the movement of human body within the detection range of infrared sensor, and automatically take pictures.The photos will be pushed to the bound mobile client.
• This function is turned off by default and can be turned on in APP settings Sensitivity level and push interval can also be set in APP.
• Device sharing: share the doorbell to others in the APP, and the shared person needs to download the APP to verify login.

(Note: It can be shared with up to 9 friends, but only one person can answer at a time)

How to Use the Doorbell

1. scan the QR code below and select proper system(iOS/android) to download app
2. Register and log in : you can register an account with email address or you can log in by guest account. Guest account is able to use all functions of the app, but device will delete all guest info after device is reset.
3. click “+” button on upper right corner, follow app instructions to add device and combine with your cellphone.
4. Binding device : this Doorbell doesnot support 5G Wi-Fi channel ! Be sure to select the 2.4G Wi-Fi channel and start binding device. 5G Wi-Fi of dual channel router usually has “-5g” mark after the name. Remember NOT to select this Wi-Fi for device binding.

For example：

• NAXCLOW_2.4G” Correct channel
• NAXCLOW_5G” Wrong channel if you have modifed the wifi channel name, make sure you choose the correct channel for binding. if you are not sure about the wifi channel, you can login your router backstage for more info. (sticker on the back of router housing)
• type router IP address in webbrowser, open the link and input user name and password.
• Working logic of doorbell push: press the doorbell after binding, the app will receive the message push, select “reject” or hang up after answering, the doorbell will enter the shutdown state, which can trigger the doorbell to send messages to the mobile phone again.

Warnings :

• please turn on Bluetooth, Wi Fi and allow all permissions of the app.
• please use this product in an environment with good Wi Fi signal and try not to stick it on the metal door.
• this product does not support 5g Wifi.
• before installing the doorbell, please conduct normal function test at the position to be installed to ensure that the product works properly.
• Remove the lens protective film after installation.

Pairing Doorbell&DingDong

1. Plug Dingdong in power souce.
2. Long press Dingdong match button for 2 seconds, indicator light on suggesting enters pairing mode.
3. Press doorbell button once, 2 devices will pair with each other, after paired successfully, indicator lights off.

Warnings:

1. During pairing, 2 devices should be as close as possible.
2. Make sure the doorbell is fully charged.
3. After pairing, the indicator light will automatically turn off.
4. If you don’t ring the doorbell within ten seconds, the dingdong indicator will go out automatically.
5. If pairing fails or re pairing is required, please repeat the pairing process.

Reset&Restore factory settings

• Reset: press and hold the doorbell key for 10 seconds until the doorbell sounds “reset succeeded”.
• Restore factory settings: in case of equipment crash or other factors, remove the doorbell and press the black button in the doorbell reset pinhole.

FCC Requirement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receivers are connected.
• Consult the dealer or an experienced radio/TV technician for help

please scan the QR code to learn the X10 product introduction and using tutorial before usage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>