iTR iMop Driving Floor Sweeper Instruction Manual

iTR iMop Driving Floor Sweeper

Replace the side brush

There are two groups of side brushes, both located at the front and bottom of the machine. There are two brush plates under each side brush.
Note: Only components sold or recommended by iTR are applicable to iMop.

1. Hold the connection between the brush plate and side brush and use downward force and you can remove the side brush;
2. Please take out the new brush plate. The brush plate and the side brush are connected by magnetic adsorption. The notch at the top of brush plate corresponds to the convex notch of the side brush, and the brush plate will automatically adsorb on the side brush.

Replace the roller brush

There are two roller brushes, which are located at the bottom of machine. When you are going to change the roller brush:

1. Firstly, please remove the roller brush cover plate. You are recommended to use a socket head wrench to unscrew the three socket head screws on the roller brush cover plate (screws are located on the right side of roller brush) , and then, the removal will be completed;
2. Please pull out two roller brushes, and then, you can replace them with new ones;

3. When installing a new roller brush, please insert the end of the roller brush with a square hole inward into the socket of the roller brush components, and then, the installation will be completed;
4. Finally, please recover the cover plate of the roller brush and screw on the three socket head screws. Please confirm the tightness of the socket head screws, and then, the replacement will be completed;

Clean the shell

You are recommended to wipe and clean with a clean cloth once a week.

Clean the screen

Please wipe the machine screen with a clean cloth.

Note:
Machine’s screen is an electronic product. Please keep away from water.

Clean the sensor

• Lidar:
  Please gently wipe the lidar with a clean cloth to ensure that the lidar surface is free of dirt.

• Ultrasonic sensor:
  User can selectively wipe the ultrasonic sensor according to the use of the machine. Please gently wipe the ultrasonic sensor with a clean cloth to ensure that the surface of the ultrasonic sensor is free of dirt.

• Binocular camera:
  Please gently wipe the binocular camera with a clean cloth to ensure that the surface of the binocular camera is free of dirt.

Machine storage

Please store the machine in a dry and cool place.

Replace battery

iTR recommends you do not replace the battery by yourself. Please contact iTR after-sales engineer if necessary.

Maintenance frequency

Canada Statement

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, u5es and can radiate radio frequency energy and, if not installed an,d used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmfu1I interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s autho rity to operate the equipment.

Contact us

Sales hotline: +86-13958085776/+86- l 3567194090 After-sales
hotline: +86-17316928285
Fax: +86-0571-87837189
Email: service@it-robo.com
Website: www.it-robo.com

Please scan QR code,and follow

iTR official account :

IT-ROBOTICS Technology Co., Ltd.

Address: Room 203, Main Building of Jieli Building, No.135 of Jichang Road, Shangcheng District, Hangzhou, Zhejiang
Tel: +86-0571-87032179
Fax : +86-0571-87837189

Sales hotline: +86-13958085776 / +86-13567194090
Email: it@it-robo.com
Website: www.it-robo.com

References

• robo.com - robo Resources and Information.
• ITR Robots Manufacturer, Commercial Robot - ITR Driverless Robot

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>