iRobot RVD-Y1 i5+ Robot Vacuum User Guide

RVD-Y1 i5+ Robot Vacuum
User Guide

Safety Information

Important Safety Information
This owner’s guide includes information for Regulatory Model(s): RVD-Y1, ADJ-N1
SAVE THESE INSTRUCTIONS
WARNING: When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS
WARNING: To reduce the risk of injury or damage, read and follow the safety precautions when setting up, using, and maintaining your robot.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

| This is the safety alert symbol. It is used to alert you to potential physical injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
---|---
| Risk of electric shock
| Risk of fire
| Separate Supply Unit
| Class II equipment
| For indoor use only
| Rated power input, a.c.
| Rated power output, d.c.
| Rated power input, d.c.
| Read operator’s manual
| Keep out of reach of children
| General symbol for recycling
BFP| Backfeed Protection

WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
NOTICE: Indicates a hazardous situation that, if not avoided, could result in property damage.

GENERAL
WARNING

• Your product is not a toy. Small children and pets should be supervised when your robot is operating.
• Do not sit or stand on your robot or Clean Base™
• Do not use unauthorised chargers. Use of an unauthorised charger could cause the battery to generate heat, smoke, catch fire, or explode.
• Your robot comes with a region approved power supply cord and is designed to be plugged into a standard household AC power socket only. Do not use any other power supply cord. For replacement cords, please contact Customer Care to ensure proper selection of country specific power supply cord.
• Do not open your robot or Clean Base™. There are no user serviceable parts inside. Refer servicing to qualified service personnel.
• Risk of electric shock, use indoors in dry locations only.
• Do not handle your robot or Clean Base™ with wet hands.
• Store and operate your robot in room temperature environments only.
• If the room to be cleaned contains a balcony, a physical barrier should be used to prevent access to the balcony and ensure safe operation.
• Clean cliff sensors to remove buildup.

ROBOT
WARNING

• Do not operate the robot in areas with exposed electrical outlets in the floor.
• Do not use this device to pick up sharp objects, glass or anything that is burning or smoking.
• Be aware that the robot moves on its own. Take care when walking in the area that the robot is operating in to avoid stepping on it.
• If the device passes over a power cord and drags it, there is a chance an object could be pulled off a table or shelf. Before using this device, pick up objects such as clothing, loose papers, pull cords for blinds or curtains, power cords and any fragile objects. Extinguish candles. Shut off portable heaters.
• Perform the required maintenance as per the Owner’s Guide to ensure safe operation of the robot and dirt disposal.
• If the robot is operating on a floor with stairs, please remove any clutter from the top step.

NOTICE

• This robot is intended for dry floor use only. Do not use this device to pick up spills. Do not allow your robot or CleanBase to become wet.

• Do not place anything on top of your robot.

• Failure to maintain cleanliness of charger contacts could result in loss of ability for the robot to charge the battery.

• Before running your robot on hard floors, please test your robot on a small section of the hard floor to ensure that it is compatible.
  Using your robot on a hard floor that is not compatible could result in damage to your floor. Contact your hard floor manufacturer with questions on compatibility.

• The failure to maintain cleanliness of charger contacts could result in loss of ability for the robot to charge the battery.

BATTERY
WARNING

• Do not open, crush, or heat above 176°F: 80°C, or incinerate. Follow the manufacturer’s instructions.
• Do not short-circuit the battery by allowing metal objects to contact battery terminals or immerse in liquid. Do not subject batteries to mechanical shock.
• Periodically inspect the battery pack for any sign of damage or leakage. Do not charge damaged or leaking battery packs, do not allow the liquid to come in contact with skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice. Place the battery in a sealed plastic bag and recycle or dispose of it safely according to local environmental regulations, or return it to your local authorised iRobot Service Center for disposal.
• Lithium ion batteries and products that contain lithium ion batteries are subject to stringent transportation regulations. If you need to ship this product (with the battery included) for service, travel, or any other reason, you MUST see the Troubleshooting section of your manual or contact customer care for shipping instructions.

CAUTION

• Battery usage by children should be supervised. Seek medical advice immediately if a cell or a battery has been swallowed.

NOTICE

• The battery pack must be removed from the robot before recycling or disposal.
• For best results, only use the iRobot Lithium Ion Battery that comes with the robot.
• Do not use non-rechargeable batteries. Use only the rechargeable battery supplied with the product. For replacement, purchase identical iRobot battery or contact iRobot Customer Care for alternative battery options.
• Always charge and remove the battery from your robot and accessories before long-term storage.

AUTOMATIC DIRT DISPOSAL
WARNING

• Do not use if the cord or plug is damaged. If appliance is not working as it should, has been dropped, damaged, left outdoors or dropped into water, return it to a service centre.
• Always disconnect your robot from the dirt disposal before cleaning or maintaining it.
• Do not use the dirt disposal as a step.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce air flow.
• To properly maintain your dirt disposal, do not place foreign objects inside and ensure that it is clear of debris.
• In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
• Do not allow liquids to get on or into the dirt disposal.
• Do not pour any liquids into the device and do not immerse in water.
• Do not use outdoors or on wet surfaces.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual.
• To reduce the risk of electric shock, unplug your dirt disposal before cleaning it.
• Keep the dirt disposal and power cord away from heated surfaces.

NOTICE

• Product may not be used with any type of power converter. Use of power converters will immediately void the warranty.
• If you live in an area prone to electrical storms, it is recommended that you use additional surge protection. Your dirt disposal may be protected with a surge protector in the event of severe electrical storms.
• Do not use without dust bag and/or filters in place.

Note: For battery recycling go to call2recycle.org; or call 1-800-822-8837

About your Roomba® Robot Vacuum

About your Clean Base™ Automatic Dirt Disposal

Using your Roomba® Robot Vacuum

Positioning the CleanBase Automatic Dirt Disposal

Note: Do not place your CleanBase in direct sunlight. Ensure that the area around the dock is free of clutter to improve docking performance.
WARNING: To prevent the risk of your robot falling downstairs, ensure that the Charging Station is placed at least 1.2 metres (4 feet) away from stairs.
Download the iRobot Home App and connect to Wi-Fi®

• Follow the step-by-step instructions to set up your Roomba® Robot Vacuum.
• Set an automatic cleaning schedule and customise cleaning preferences.
• Create smart maps to tell your robot where, when and how to clean.

Charging

• Place the robot on the CleanBase to activate the battery.
  Note: Your robot comes with a partial charge, but we recommend that you charge the robot for 3 hours prior to starting the first cleaning job.

• If your robot needs to recharge mid-clean, it will return to its CleanBase. Once it is sufficiently charged, it will then resume the cleaning job where it left off.

• The robot uses a small amount of power whenever it is on the CleanBase. You can put the robot in a furtherreduced power state when not in use. For instructions and more details on this Reduced Power Standby Mode, refer to the iRobot HOME App.

• For long-term storage, turn off the robot by removing it from the CleanBase and holding down for 10 seconds. Store the robot in a cool, dry place.

Cleaning

Remove excess clutter from floors before cleaning. Use your robot frequently to maintain well-conditioned floors.

• Your robot will automatically explore and clean your home. It will return to the CleanBase at the end of a cleaning job and whenever it needs to recharge.
• To send the robot back to its CleanBase, tap . A blue light ring pattern will indicate that the robot is seeking the CleanBase.
• When your robot detects an especially dirty area, it will go into Dirt Detect™ mode, moving over the area multiple times until it senses that the area has been sufficiently cleaned. The light ring indicator will flash blue.
• Tap  to spot clean a designated area. The robot will spiral outward about 3 feet (1 metre) and then spiral inward to end where it started. The light ring indicator will show a blue spiral.

About your Automatic Dirt Disposal
While cleaning, your robot will automatically return to the dirt disposal to empty its bin and recharge as needed.
The dirt disposal’s LED indicator will turn solid red when a new bag is needed.
If a clog is detected, the dirt disposal will trigger additional attempts to automatically clear the clog.
Note: If you place your robot on the dirt disposal by hand, it will not empty automatically. In this case, use the iRobot HOME App or hold the button down for 2-5 seconds.

Care and Maintenance

Care and Maintenance Instructions
To keep your dirt disposal running at peak performance, follow these care procedures:

Every 2 months
Full Bin Sensor| Clean every 2 weeks|
Front Caster Wheel| Clean every 2 weeks| Every 12 months
Edge-Sweeping Brush and Multi-Surface Brushes| Clean once a month (twice a month if you have a pet)| Every 12 months
Sensors and Charging Contacts| Clean once a month| –

Note: iRobot manufactures various replacement parts and assemblies. If you think you need a replacement part, please contact iRobot Customer Care for more information.

Emptying the Bin

1. Press the bin release button to remove bin.
2. Open bin door to empty bin.
3. Place bin back in the robot.

Cleaning the Filter

1. Remove the bin. Remove the filter by grasping both ends and pulling out.
2. Remove debris by tapping the filter against your rubbish bin.
3. Reinsert filter with ridged grips facing out. Place bin back in the robot.

Important: The robot will not run if the filter is not installed correctly. Replace the filter every two months.

Cleaning the Full Bin Sensors

1. Remove and empty the bin.
2. Wipe the inner sensors with a clean, dry cloth
3. Wipe the bin door with a clean, dry cloth.

Washing the Bin
Important: Do not wash the filter. Remove the filter before washing the bin.

1. Release the bin, remove the filter, and open the bin door.
2. Rinse the bin using warm water. Note: Bin is not dishwasher safe.
3. Make sure the bin is completely dry. Reinsert filter and place bin back in the robot.

Cleaning the Edge-Sweeping Brush

1. Use a small screwdriver to loosen the screw holding the Edge-Sweeping Brush in place.
2. Pull to remove the Edge-Sweeping Brush. Remove any hair or debris, then reinstall the brush.

Cleaning the Front Caster Wheel

1. Pull firmly on the front wheel module to remove it from the robot.
2. Pull firmly on the wheel to remove it from its housing (see illustration below).
3. Remove any debris from inside the wheel cavity.
4. Reinstall all parts when finished. Make sure the wheel clicks back into place.

Important: A front wheel clogged with hair and debris could result in damage to your floor. If the wheel is not spinning freely after you have cleaned it, please contact Customer Care.

Cleaning the Multi-Surface Brushes

1. Pinch the brush frame release tab, lift the tab, and remove any obstructions.
2. Remove the brushes from the robot. Remove the brush caps from the ends of the brushes. Remove any hair or debris that has collected beneath the caps. Reinstall the brush caps.
3. Remove any hair or debris from the square and hexagonal pegs on the opposite side of the brushes.
4. Remove the bin from the robot and clear any debris from the vacuum path.
5. Reinstall the brushes in the robot. Match the shape of the brush pegs with the shape of the brush icons in the cleaning head module.

Cleaning the Visual Docking Target Sensors, IR Window, and Charging Contacts

1. Wipe sensors and charging contacts with a clean dry cloth. You can alternately use a pad of melamine foam to remove built up debris on the robot and CleanBase charging contacts.
2. Inspect the visual docking target, IR window, and charging contacts to make sure that they are clear of debris. Wipe with a clean, dry cloth.

Important: Do not spray cleaning solution or water onto the sensors or sensor openings.
Removing Debris from Blower Cover
Inspect blower cover for any lint or debris build-up, and wipe with a clean dry cloth to remove.

Replacing the Bag

1. Lift up on the canister lid to open.

2. Pull up on the plastic card to remove the bag from the canister.
   Note: This will seal the bag so dust and debris cannot escape.

3. Discard the used bag.

4. Install a new bag, sliding the plastic card into the guide rails.

5. Press down on the lid making sure that it is completely closed.

Note: To achieve optimal performance with your robot and automatic dirt disposal, clean and/or replace your robot’s filter as needed.

Troubleshooting

Automatic Dirt Disposal
Your dirt disposal will tell you if something is wrong via an LED indicator on the front of the canister and through the iRobot HOME App.

2. Make sure that the bag is securely inserted.
3. If problem persists, remove any debris from the port on the bottom of your robot and the dirt disposal.
Blinking red| There is a leak or a clog in the dock evacuation path| 1. Make sure that the canister lid is pushed down and firmly sealed. Hold the clean button on your robot down for 2-5 seconds to manually empty the bin.
2. Remove any debris from the port on the bottom of your robot and dirt disposal.
3. Unplug the dirt disposal from the wall. Place it on its side and inspect the debris evacuation tube for debris. If necessary, remove the tube to clear any debris.

This product has been equipped with a thermal protector designed to protect against damage due to overheating. If the protector operates, the motor will stop running. If this happens, unplug the unit, allow it to cool for 30 minutes, clear any obstructions from the evacuation port and evacuation tube, then plug the unit back in.
Robot
Your robot will tell you something is wrong by playing an audio alert and turning the light ring indicator red. Press CLEAN for details. Further support and instructional videos are available in the iRobot HOME App.
If you are unsure if the robot is finished or paused, consult the iRobot HOME App to check on its status.

Battery Safety & Shipping
For best results, only use the iRobot Lithium Ion Battery that comes with your robot.
WARNING: Lithium ion batteries and products that contain lithium ion batteries are subject to stringent transportation regulations. If you need to ship this product for service, travel or any other reason, you MUST follow the below shipping instructions.

• Battery MUST be turned off before shipping.
• Turn off the battery by removing the robot from the CleanBase and holding down for 10 seconds. All indicators will turn off.
• Package the robot securely for shipping.
• If you need further assistance, contact our Customer Care team or visit global.irobot.com.

Regulatory Information

FCC Supplier’s Declaration of Conformity
iRobot Corporation
Roomba Model: RVD-Y1
Contains FCC ID: UFE-AXFY1 and contains IC: 6652A-AXFY1
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device contains a licence-exempt transmitter/receiver that complies with Innovation, Science and Economic Development (ISED) Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1) This device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.

• Changes or modifications not expressly approved by iRobot Corporation could void the user’s authority to operate the equipment.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference to radio communication will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than the necessary for successful communication.
• FCC Radiation Exposure Statement: This product complies with FCC §2.1091(b) for mobile device RF exposure limits, set forth for an uncontrolled environment and is safe for the intended operation as described in this manual. Per FCC requirements, maintain a distance of more than 8 inches (20cm) between any person and the host device (Roomba robot).
• ISED Radiation Exposure Statement: This product complies with the Canadian Standard RSS-102 for portable RF exposure limits, set forth for an uncontrolled environment and is safe for the intended operation as described in this manual. Per ISED requirements, maintain a distance of more than 8 inches (20 cm) between any person and the robot.

iRobot Corporation, 8 Crosby Drive, Bedford, MA 01730 USA.
https://global.irobot.com
For battery recycling go to call2recycle.org; or call 1-800-822-8837

iRobot Customer Care

USA & Canada
If you have questions or comments about your dirt disposal, please contact iRobot before contacting a retailer.
You can start by visiting global.irobot.com for support tips, frequently asked questions, and information about accessories. This information can also be found in the iRobot HOME App. If you need further assistance, call the US Customer Care team at 877-855-8593.
iRobot USA Customer Care Hours

• Monday to Friday, 9AM — 9PM Eastern Time
• Saturday and Sunday 9AM — 6PM Eastern Time

Outside USA & Canada
Visit global.irobot.com to:

• Learn more about iRobot in your country
• Get hints and tips to improve your product performance
• Get answers to questions
• Contact your local support centre

©2022 iRobot Corporation, 8 Crosby Drive, Bedford, MA 01730, USA. All rights reserved. iRobot is a registered trademark of iRobot Corporation, Roomba Robot Vacuum, Clean Base and Dirt Detect are trademarks of iRobot Corporation. Wi-Fi and the Wi-Fi logo are registered trademarks of Wi-Fi Alliance. Apple and App Store are trademarks of Apple Inc., registered in the US and other countries. Google Play is a trademark of Google LLC.
For more information, visit global.irobot.com

Documents / Resources

| iRobot RVD-Y1 i5+ Robot Vacuum [pdf] User Guide
RVD-Y1 i5 Robot Vacuum, RVD-Y1, i5 Robot Vacuum, Robot Vacuum, Vacuum
---|---

References

• Call2Recycle | Leading the Charge For Battery Recycling
• Global.iRobot.com
• Global.iRobot.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>