LiftMaster 886LMW Multi-Function Control Panel Instruction Manual

: June 11, 2024
: LiftMaster

Table of Contents

886LMW Multi-Function Control Panel
UNATTENDED OPERATION
INSTALLATION
PROGRAM
FEATURES
MOTION SENSOR
MAINTENANCE ALERT SYSTEM (MAS)
ONE YEAR LIMITED WARRANTY
Documents / Resources

MULTI-FUNCTION CONTROL PANEL
(SECURITY+ 2.0® ) MODEL 882LMW AND
PREMIUM MOTION-DETECTING
CONTROL PANEL MODELS 881LMW AND 886LMW

886LMW Multi-Function Control Panel

WARNING
To prevent possible SERIOUS INJURY or DEATH from electrocution:

Be sure power is NOT connected BEFORE installing door control.
Connect ONLY to 12 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.
NEVER permit children to operate or play with door control push buttons or remote control transmitters.
Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.
Unattended devices and features are to be used ONLY with sectional doors.

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
For use with Security+ 2.0® Garage Door Openers, Wi-Fi® enabled Security+ 2.0® Garage Door Openers (indicated by the Wi-Fi logo on the garage door opener cover) and My® accessories.

UNATTENDED OPERATION

The Timer-to-Close (TTC) feature, the MyQ ® Smartphone Control app, and MyQ ® Garage Door and Gate Monitor are examples of unattended close and are to be used ONLY with sectional doors. Any device or feature that allows the door to close without being in the line of sight of the door is considered unattended close. The Timer-to-Close (TTC) feature, the MyQ ® Smartphone Control, and any other MyQ ® devices are to be used ONLY with sectional doors.

INSTALLATION

Unplug the garage door opener. Disconnect the battery (if applicable).

Connect the wires to the back of the door control.
Secure the door control to the wall.
Connect the wires to the garage door opener.
Plug in the garage door opener and reconnect the battery. The command LED on the door control will blink if installed correctly. To synchronize the garage door opener and the door control, press the push bar up to 3 times, until the garage door opener activates.

PROGRAM

REMOTE CONTROL

Press the LEARN button on the door control twice. The
Command LED will blink.
Press and release the button on the remote control that you wish to operate your garage door.
The garage door opener lights will flash (or two clicks will be heard) and the Command LED will stop blinking when the code has been programmed.

KEYLESS ENTRY

Press the LEARN button on the door control twice. The Command LED will blink.
Enter a 4-digit personal identification number (PIN) on the keypad. Then press the ENTER button.
The garage door opener lights will flash (or two clicks will be heard) and the Command LED will stop blinking when the code has been programmed.

CONNECT YOUR GARAGE DOOR OPENER TO YOUR HOME WI-FI® NETWORK (for Wi-Fi garage door openers ONLY)

Lift the push bar on the door control. Press and release the LEARN button. The garage door opener will beep once and the command LED on the door control will blink to indicate Wi-Fi learn mode. You have 20 minutes to complete the connection process.
On your mobile device, go to Settings > Wi-Fi and select the network with the “MyQ-” preﬁ x.
Launch the web browser on your smartphone or tablet. Enter setup.myqdevice.com into the browser address bar. Follow the on screen prompts to connect the garage door opener to your Wi-Fi network. The My serial number will display on screen. Write the serial number in the space below.
Download the My app from the App Store® or Google Play™ store. Sign up for your
My account and add the My serial number to your account.
If you are unsuccessful adding your device, try an alternate web browser or visit WiFiHelp.LiftMaster.com.

FEATURES

LOCK
Prevents activation of the garage door opener from remote controls while still allowing activation from the door control and keyless entry. Factory default is OFF.
Turn ON: Press and hold the LOCK button for 2 seconds. The command LED will blink as long as the lock feature is activated.
Turn OFF: Press and hold the LOCK button again for 2 seconds. The command LED will stop flashing and normal operation will resume.

LIGHT
Press the LIGHT button to turn the garage door opener lights on or off. The LIGHT button will not control the lights when the door is in motion. When the lights are turned on they will stay on until the LIGHT button is pressed again, or until the garage door opener is activated. Once the garage door opener is activated the lights will turn off after a specified period of time (see below).

TO CHANGE THE AMOUNT OF TIME THE GARAGE DOOR OPENER LIGHTS WILL STAY ON
Press and hold the LOCK button until the garage door opener lights flash (about 10 seconds). The garage door opener lights will flash up to 4 times to indicate current setting:

Flash = Lights stay on 1 ½ minutes
Flashes = Lights stay on 2 ½ minutes
Flashes = Lights stay on 3 ½ minutes
Flashes = Lights stay on 4 ½ minutes (factory default)

Repeat the steps above until your desired time frame is reached.
LIGHT FEATURE FOR THE SAFETY REVERSING SENSORS
The garage door opener lights will turn on when the safety reversing sensor beam is interrupted. Factory default is ON.
Turn ON: Start with the garage door opener lights on. Press and hold the LIGHT button to turn off the light, continue to hold until the light turns on (about 10 seconds).
Turn OFF: Start with the garage door opener lights off. Press and hold the LIGHT button to turn on the light, continue to hold until the light turns off (about 10 seconds).

MOTION SENSOR

( for models 881LMW and 886LMW ONLY)
The motion sensor will automatically turn on the garage door opener lights when motion is detected. The lights will come on for the set period of time, then shut off. The factory default is on for 4-1/2 minutes.
Turn ON/OFF: Slide the motion sensor switch ON or OFF.

MODEL 882LMW

MODELS 881LMW AND 886LMW

MAINTENANCE ALERT SYSTEM (MAS)

When the garage door opener needs to be serviced (approximately 4500 garage door opener cycles) the command and service LEDs will alternately blink back and forth. Factory default is OFF.
Turn ON/OFF: Press and hold the LEARN button. Then press the LIGHT button. The service LED will blink the status; ON is 2 blinks and OFF is 3 blinks.

TIMER-TO-CLOSE (TTC) (for model 881LMW ONLY)
DO NOT enable TTC if operating a one-piece door. TTC is to be used ONLY with sectional doors.
The TTC can be set to automatically close your garage door after a specified period of time (1, 5, or 10 minute intervals). Once the TTC has been set and the door is open, the selected close interval will blink and begin to count down to close the door. The garage door opener will beep and the lights will ﬂ ash before closing the door.
This feature is NOT intended to be the primary method of closing the door. A keyless entry should be installed in the event of an accidental lock out when using this feature.
Turn ON: Press and hold the ON button until one of the TTC LEDs light up.
Change the TTC Time Intervals: Press the ON button a second time to cycle through the time interval options (the corresponding TTC LED will light for each time interval). The garage door opener light bulbs will blink as confirmation.
Temporarily suspend the TTC: Press and release the HOLD OPEN button.
Press and release the HOLD OPEN button again to resume normal TTC operation.
Turn OFF: Press and hold the OFF button until all TTC LEDs turn off and a beep is heard from the garage door opener.

The TTC WILL NOT work under the following conditions:

If the door encounters an obstruction while closing, the garage door opener will make a second attempt to close the door. If the obstruction has not been cleared after the second attempt, the garage door opener will reverse open, stop and WILL NOT close until the obstruction has been cleared.
If the safety reversing sensors are incorrectly installed or misaligned the garage door will reverse open and WILL NOT close until the safety reversing sensors are correctly installed and aligned. When the safety reversing sensors have been aligned, the door will close when the garage door opener is activated.
If the garage door opener is operating by battery power the TTC will not work.

NOTE: If you have an 880LMW installed and the TTC is set to a custom time, the 3 LED’s on the 881LMW will blink. If the 3 LED’s are blinking and you have an 881LMW ONLY, press the ON button to set the time properly.

ONE YEAR LIMITED WARRANTY

Lift aster warrants to the first consumer purchaser of this product that it is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase.
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or mode cations of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards for Home or ofﬁce use. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.

1-800-528-9131
LiftMaster.com
Wi-Fi® is a registered trademark of Wi-Fi Alliance.
App Store is a service mark of Apple Inc.
Google Play is a trademark of Google Inc.
Wi-Fi® stone marque Wi-Fi Alliance.
© 2016, Lift aster
All Rights Reserved
Toups droits reserves
114A4972B

Documents / Resources

| LiftMaster 886LMW Multi-Function Control Panel [pdf] Instruction Manual
886LMW Multi-Function Control Panel, 886LMW, Multi-Function Control Panel, Control Panel, Panel
---|---