OASIS 222391 Wired Headphone Wireless Mouse User Manual
- June 11, 2024
- Oasis
Table of Contents
222391 Wired Headphone Wireless Mouse
User Manual
WIRED HEADSET
PRODUCT KEY
- Adjustable Headband
- Rotating Microphone
- Volume Control Button
- Comfort Fit Ear Cups
- 3.5mm Aux plug
- Microphone rotates up into standby mode when not in use.
- Turn the Volume control button up to decrease volume and down to increase it.
SPECIFICATIONS
Frequency: 2402~2480MHz
Sensitivity: 108dB/mW
Impedance: 32ohm
Max input power: 45mW
Cord length: 1.7M
Plug: 3.5mm plug
Drive unit: 40mm
CONNECTING
Plug the 3.5mm aux plug into the audio output port on your media-playing
device.
WIRELESS MOUSE
PRODUCT KEY
- Left Click
- Right Click
- Scroll Wheel
- Battery Compartment
- Wireless USB Connector
- Optical Lens
INSTALLATION
-
Open the Battery Compartment and remove the Wireless USB Connector.
-
Place two AAA batteries(included) into the Battery Compartment and align the symbols on the battery.
Replace the battery compartment cover. -
Plug the Wireless USB Connector into your computer or device.
-
The Wireless mouse should begin to work automatically.
TROUBLE SHOOTING
If the cursor doesn’t move when you move the mouse…
- Check the Wireless USB Connector connection. Try inserting it into another USB port on your computer.
- Take the batteries out and reinstall it. Replace the batteries with two that has a full charge.
IMPORTANT NOTE: The battery should not be opened or burned. Exposure to
the ingredients contained within or their combustion products could be
harmful. Storage: Store in a cool, well ventilated area. Elevated
temperatures can result in shortened battery life.
Mechanical Containment: Designers of any water or air-tight device should be
aware of the normal evolution of hydrogen gas from alkaline batteries. This
gas must be either absorbed or allowed to escape to avoid a potential safety
issue.
Handling: Accidental short circuit for a few seconds will not seriously
affect the battery. Prolonged short circuit will cause the battery to lose
energy through heating, and can cause the safety release vent to open. Sources
of short circuits include jumbled batteries in bulk containers, metal jewelry,
metal covered tables or metal belts used for assembly of batteries into
devices.
Soldering directly to a battery is not recommended. If welding to the battery
is required, consult your Energizer sales representative for proper
precautions to prevent seal damage or short circuit.
Charging: This battery is manufactured in a charged state. It is not
designed for recharging. Recharging can cause battery leakage or, in some
cases, high pressure rupture. Inadvertent charging can occur if a battery is
installed backwards.
Labeling: The label acts as an electrical insulation for the battery can.
Damage to the label can increase the potential for a short circuit.
WARNING: Do not install backwards, charge, put in fire, or mix with other
battery types as it may explode or leak causing injury. Replace all batteries
at the same time.
Ingestion: Do not induce vomiting or give food or drink.
Seek medical attention immediately. CALL NATIONAL BATTERY INGESTION HOTLINE
for advice and follow-up (202-625-3333)
collect day or night.
The following instructions apply to exposure of internal components.
Inhalation: Provide fresh air and seek medical attention.
Skin Contact: Remove contaminated clothing and wash skin with soap and water.
If a chemical burn occurs or if irritation persists, seek medical attention.
Eye Contact: Immediately flush eyes thoroughly with water for at least 15
minutes, lifting upper and lower lids, until no evidence of the chemical
remains. Seek medical attention.
In case of fire, it is permissible to use any class of extinguishing medium on
these batteries or their packing material. Cool exterior of batteries if
exposed to fire to prevent rupture.
Dispose of in accordance with all applicable federal, state and local
regulations. Appropriate disposal technologies include incineration and land
filling.
Contact Info: contact@culturefly.com
FCC Satement
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation
US Company Name: Oasis Compliance, Inc.
US Company Address: 3313 Verdi Dr, San Jose, CA 95111
Telephone Number: (01) 2026028330
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>