NOBLE UH30-E Energy Efficient High Temp Undercounter

Product Information

The NOBLE UNDERCOUNTER DISHMACHINES are designed for commercial use in restaurants, hotels, and other foodservice establishments. The machines come in two models: NOBLE UH30-E and NOBLE UH30-E-SEER. The machines are capable of washing dishes, glasses, and utensils. The machines have a compact design that allows them to fit easily under a countertop.

Features

• Compact design
• Capable of washing dishes, glasses, and utensils
• Designed for commercial use in restaurants, hotels, and other food service establishments

Product Specifications

• Models: NOBLE UH30-E and NOBLE UH30-E-SEER
• Water consumption: Varies based on load size and cycle time
• Electrical requirements: Varies based on model and voltage
• Dimensions: Varies based on model

Product Usage Instructions

Before using the NOBLE UNDERCOUNTER DISHMACHINES, make sure to read the entire installation, operation, and service manual provided with the machine. Follow the instructions carefully to ensure proper machine operation and to avoid injury or damage to the machine.

Installation

1. Select a location for the machine that is level and has access to the necessary utilities.
2. Install the machine according to the instructions provided in the installation section of the manual.
3. Connect the necessary utilities, such as water, electricity, and drainage, according to the instructions provided in the manual.

Operation

1. Load the machine with dishes, glasses, and utensils according to the instructions provided in the manual.
2. Select the appropriate wash cycle according to the instructions provided in the manual.
3. Start the machine and allow it to complete the wash cycle.
4. Unload the clean dishes, glasses, and utensils from the machine.

Maintenance

1. Clean the machine regularly according to the instructions provided in the manual.
2. Replace any worn or damaged parts according to the instructions provided in the manual.
3. Perform regular maintenance tasks, such as checking and cleaning filters, according to the instructions provided in the manual.

By following these usage instructions and properly maintaining the NOBLE UNDERCOUNTER DISHMACHINES, you can ensure that they will provide reliable service for years to come.

NOBLE UNDERCOUNTER DISH MACHINES INSTALLATION, OPERATION, AND SERVICE MANUAL NOBLE UH30-E NOBLE UH30-E-SEER UH30-E Manual · 07610-004-45-09-Q

REVISION HISTORY

B

| ****

9-6-17

| ****

JH

| ****

8532

| Updated depiction of the air-gap on pg. 6. Removed references to “screen” on pg. 20. Added com- munication cable (05700-004-33-64) to pg. 23. Corrected chemical tubes on pg. 25 and added tube length and color. Removed fill line (05700-002-62-37) from wash hub on pg. 30. Replaced 7/8″ dis- charge hose with 5/8″ discharge hose (05700-004-46-28) on pg. 31. Updated view of inlet plumbing on pg. 34 to show angle of elbow and adapter. Updated schematic to revision E.
C| 1-19-18| JH| 8537

8574

| Added the UH30-E-SEER to the manual. Updated the Door Assembly pages. Added item #10 on pg.

48. Corrected P/N for item #10 on pg. 52.

D

| ****

2-7-19

| ****

JH

| ****

8585

8599

8619

8648

| Added PRV to view on pg. 3. Added note about hot water heates to pg. 7. Added motor rotation section to pg. 9. Added programming instructions and fault codes to pgs. 22–26. Updated P/N for item #2 on pg. 29. Updated pg. 31 to show panel and membrane together. Added item #14 on pg. 33. Updated item

11 on pg. 40. Added Door Interlock to pg. 41. Changed rinse arm bearing

assembly on pg. 44. Changed rinse arm bearing kit P/N on pg. 44. Updated SEER plumbing, pgs. 48–49. Added note about water connection point to pg. 48. Updated pgs. 54–55. Added back panel and gaskets to pg. 56. Added new drain water tempering kit and 460 V drain water tempering kit to

pg. 57. Updated schematics on pgs. 58–59.

E| 4-24-19| JH| 19-553| Updated 208–230 V schematic.

F

| ****

5-11-20

| ****

JH

| 8664

8709

8721

19-730

| Revised Programming Chemical Feeder Pumps section. Updated pump assemblies on pgs. 38-39. Added drip shield and gasket to pg. 39. Updated P/N for item

12 on pg. 57. Added wash heater gasket to pg. 59. Updated SEER System pages.

G| 11-16-20| JH| N/A| Revised drain line size. Updated dimensional drawing. Added F12 in Fault Codes section. Corrected P/N of Item #8 on pg. 33. Adjusted quantities on pg. 42. Updated Item #3 on pg. 46.
H| 2-5-21| JH| 8810| Changed Priming Chemical Feeder Pumps section. Added spacer and updated blower wheel P/N on SEER System pages.
J| 6-30-21| JH| 8808

20-931

| Updated Fault Codes section. Changed pressure regulator on SEER unit. Updated rinse plumbing assembly. Removed resistor and bracket from electrical panels.
K| 12-20-21| JH| N/A| Updated water consumption per Energy Star 3.0 report. Revised Electrical Requirements section. Corrected P/N for 460 V door interlock solenoid. Added description of Energy Saver Mode.

L

| ****

3-11-22

| ****

JH

| ****

N/A

| Updated Operating Parameters section to show with and without load time. Corrected Electrical Requirements section and added MCA/MOP. Changed P/N of item #8 on pg. 33. Updated view in Chemical Feeder Pumps section. Changed P/N of item #11 on pg. 45. Added Motors page. Added gasket to SEER System page. Added Frame page.
M| 5-9-22| JH| 22-1201

22-1202

| Removed water hardness test strip. Updated Chemical Feeder Pumps section with black dot roller. Corrected Rinse Tank section to show plumbing.

N

| ****

6-14-22

| ****

JH

| ****

8888

| Removed universal timer from 208-230 V. Combined 208-230 V UH30-E and UH30-E SEER electrical panels into one control panel with new I/O module. Added new chemical feeder pumps for 208-230 V. Added new door interlock for UH30-E-SEER 208-230 V. Updated 208-230 V schematic.
P| 7-7-22| JH| N/A| Added program number for each model to the Programming section.

Q

| ****

11-29-22

| ****

JH

| 8901

22-1445

22-1503

| Removed universal timer from 460 V. Combined 460 V UH30-E and UH30-E SEER electrical panels into one control panel. Removed old 460 V chemical feeder pumps and door interlock. Changed tubing. Updated peri-pumps to black components. Updated 460 V schematic.

NOMENCLATURE

UH30-E
Undercounter dish machine; high-temperature, hot-water sanitizing, with a booster tank and detergent and rinse-aid chemical feeder pumps.

UH30-E-SEER
Undercounter dish machine; high-temperature, hot-water sanitizing, with a booster tank and detergent and rinse-aid chemical feeder pumps. Equipped with Steam Elimination and Energy Recovery System (SEER). The manufacturer provides technical support for all of the dishmachines detailed in this manual. We strongly recommend that you refer to this manual before making a call to our technical support staff. Please have this manual open when you call so that our staff can refer you, if necessary, to the proper page. Technical support is not available on holidays. Contact technical support toll free at 1-888-800-5672. Technical support is available for service personnel only.

SYMBOLS

• Risk of Injury to Personnel
• WARNING
• Risk of Damage to Equipment
• CAUTION
• Risk of Electrical Shock
• Caustic Chemicals
• Reference Data Plate
• Lockout Electrical Power
• NOTICE – Important Note
• Instructions Hyperlink

ABBREVIATIONS & ACRONYMS

ANSI – American National Standards Institute GHT – Garden Hose Thread GPG – Grains per Gallon GPM – Gallons per Minute HP – Horse Power Hz – Hertz ID – Inside Diameter kW – Kilowatts MCA – Minimum Circuit Ampacity MOP – Maximum Overcurrent Protection NFPA – National Fire Protection Association NPT – National Pipe Thread OD – Outside Diameter PRV – Pressure Regulating Valve PSI – Pounds per Square Inch V – Volts

SPECIFICATIONS

UH30-E-SEER DIMENSIONS

LEGEND
A – Electrical Connection
B – Water Inlet (with 6′ Hose) (3/4″ Male GHT, connect to true 1/2″ ID line, 40­90 °F)
C – Drain Hose (5/8″ ID, install into 1 1/2″ MIN Drain with Air-gap)
D – Chemical Port

All dimensions from the floor can be increased 1″ using the machine’s adjustable feet.

UH30-E OPERATING PARAMETERS

UH30-E

Operating Capacity:
Racks per Hour Dishes per Hour Glasses per Hour

36 (27)* 900 1296

Tank Capacity (Gallons):

Wash Tank 3

Rinse Tank 1.66

NOTICE Always refer to machine data plate for specific electrical and water requirements. The material provided on this page is for reference only and is subject to change without notice.

Cycle Times (Seconds):

Cycle I Wash 80 Rinse 9 Dwell 11 Total 100

Cycle II Wash 148 Rinse 9 Dwell 11 Total 168

Cycle III Wash 248 Rinse 9 Dwell 11 Total 268

Incoming water is from a “hot” water line.

Water Temperatures (°F):
Minimum Wash Temperature Minimum Rinse Temperature Minimum Incoming Water Temperature

Other Water Requirements:
Water Flow Pressure (PSI) Flow Rate Minimum (GPM) Water Line Size (NPT)

Drain Line Size (NPT)

Gallons per Hour (GPH) Gallons per Rack (GPR) 155 180 110
10 4.33 3/4″ Male GHT Connect to true 1/2″ ID Line 5/8″ ID Connect to MIN 1 1/2″ Drain with Air-gap 21.6 (16.2)** 0.60

Racks per hour calculated with NSF suggested load time of :30 for front- opening dishmachines.
Gallons per hour calculated with NSF suggested load time of :30 for front- opening dishmachines.

UH30-E-SEER OPERATING PARAME- UH30-E-SEER

Operating Capacity:
Racks per Hour Dishes per Hour Glasses per Hour

24 (20)* 600 864

Tank Capacity (Gallons):

Wash Tank

3

Rinse Tank

1.66

NOTICE Always refer to machine data plate for specific electrical and water requirements. The material provided on this page is for reference only and is subject to change without notice.

Cycle Times (Seconds):

Cycle I
Wash 80
Rinse 9 Dwell 11 SEER 45 Total 145

Cycle II
Wash 148
Rinse 9 Dwell 11 SEER 45 Total 213

Incoming water is from a “cold” water line.

Water Temperatures (°F):
Minimum Wash Temperature Minimum Rinse Temperature Minimum Incoming Water Temperature Maximum Incoming Water Temperature

Cycle III Wash 248 Rinse 9 Dwell 11 SEER 45 Total 313 155 180 40 90

Other Water Requirements:
Water Flow Pressure (PSI) Flow Rate Minimum (GPM) Water Line Size (NPT)
Drain Line Size (NPT)
Gallons per Hour (GPH) Gallons per Rack (GPR)

10 4.33 3/4″ Male GHT Connect to true 1/2″ ID Line 5/8″ ID Connect to MIN 1 1/2″ Drain with Air-gap
14.4 (12.0)** 0.60

07610-004-45-09-Q

*Racks per hour calculated with NSF suggested load time of :30 for front-opening dishmachines.
**Gallons per hour calculated with NSF suggested load time of :30 for front- opening dishmachines.

ELECTRICAL REQUIREMENTS

NOTICE
All electrical ratings provided in this manual are for reference only. Always refer to machine data plate to get exact electrical information for this machine. All electrical work performed on machines should be done in accordance with applicable local, state, territorial, and national codes. Work should only be performed by qualified electricians and authorized service agents.

Amperage loads for motors and heaters are indicated on machine data plate.

The electrical configurations are as follows:
Available Electrical Characteristics: · 208 V, 60 Hz, Single-phase · 230 V, 60 Hz, Single-phase · 460 V, 60 Hz, Three-phase
Available Wash Motors: · 1 HP
Available Wash Tank Heaters: · 3.3 kW (208 V)/4.0 kW (230 V) · 3.7 kW (460 V)
Available Rinse Tank Heaters: · 4.1 kW (208 V)/5.2 kW (230 V) · 5.0 kW (460 V)

UH30-E/UH30-E-SEER Electrical Characteristics
VOLTS 208 230 460

PHASE 1

1

3

FREQ 60

60

60

WASH MOTOR AMPS

5.0 A

WASH HEATER 15.7 A
AMPS

RINSE HEATER 19.7 A
AMPS

5.0 A 17.4 A 22.6 A

2.0 A 4.6 A 6.3 A

TOTAL LOAD

24.7 A 27.6 A

8.3 A*

MCA 25.9 A 28.8 A 8.8 A

MOP 30 A 30 A 15 A

The UH30-E is designed so the heaters never run simultaneously. Total Load is based on the higher of the two loads.
07610-004-45-09-Q

INSTALLATION

Installation Instructions

INSPECTION Before installing machine, check packaging and machine for damage. Damaged packaging might be an indication of damage to machine. If there is any type of

Do not throw away packaging if damage is evident!
damage to both packaging and unit, do not throw away the packaging. The machine has been inspected at the factory before shipping and is expected to arrive in new, undamaged condition. However, rough handling by carriers or others might result in damage to machine while in transit. If this occurs, do not return machine to the manufacturer. Instead, contact the carrier and ask them to send a representative to the site to inspect the damage and request that an inspection report be completed.

Contact the carrier and dealer within 48 hours of receiving machine.

UNPACKING
The machine should be unpacked and removed from pallet before installing. Open front door and remove all materials from inside. Once unpacked, verify there are no missing parts. If a part is missing, contact manufacturer immediately.

PLUMBING
All plumbing connections must be made to adhere to local, state, territorial, and national codes. The installing plumber is responsible for ensuring the incoming water lines are flushed of debris before connecting to machine. Note that chips and materials

Plumber must flush incoming water line!
from cutting processes can become lodged in the solenoid valves and prevent them from opening or closing. Any valves that are found to be fouled or defective because of foreign matter left in the water line, and any subsequent damage, are not the responsibility of the manufacturer. See the UH30-E Dimensions or UH30-E-SEER Dimensions page (depending on your model) and reference item “B” for water inlet connection location.

NOTICE
The manufacturer does NOT endorse “Tankless On-demand” water heaters for use with their dishmachines. The manufacturer DOES endorse, and highly recommends, the standard “Tank” style water heaters, sized to properly handle the water heating requirements of the facility.

WATER SUPPLY A water hardness test must be performed. If water hardness is higher than 3 GPG and

CONNECTIONS

a water softener is not being used, install an SPS (see Plumbing Options page) into the water line between the facility water line and machine water line (installed at the

WATER HARDNESS factory). Observe proper inlet/outlet water directions. A water shut-off valve should be

HIGHER THAN 3 GPG installed before installing the SPS to allow access for service. The water supply must be capable of a minimum of 10 PSI “flow” pressure at the recommended temperature indicated on the data plate. A water hardness test must be performed.

Facility Shut-off Adapter Water Line Valve

SPS

Adapter

Machine Water Line

Example

*Adapters needed will vary.

07610-004-45-09-Q

7

WATER SUPPLY If water hardness tests at 3 GPG or lower, connect machine water line (installed at

CONNECTIONS:
the factory) to the facility water line. A water shut-off valve should be installed in the water line between the facility supply and machine to allow access for service. The

WATER HARDNESS water supply line must be capable of a minimum of 10 PSI “flow” pressure at the

LOWER THAN 3 GPG recommended temperature indicated on the data plate.

PRESSURE The manufacturer recommends the installation of a pressure regulating valve (PRV)

REGULATOR in the incoming water line to ensure proper flow rate at all times and offers them as an option (see the Plumbing Options page). The PRV comes standard on the UH30-E-

Take care not to confuse SEER. Do not confuse static pressure with flow pressure. Static pressure is the line static pressure with pressure in a “no flow” condition (all valves and services are closed). Flow pressure is flow pressure! the pressure in the fill line when the fill valve is opened during the cycle.

SHOCK ABSORBER The manufacturer also recommends the installation of a shock absorber on the incoming water line and offers them as an option (see the Plumbing Options page). A shock absober comes standard on the UH30-E-SEER. This prevents water hammer or hydraulic shock–induced by the solenoid valve as it operates–from causing damage to the equipment.

CONNECTING THE The machine has a pumped (pressure) drain capable of pumping waste water to

DRAIN LINE
a height of 24″ above the floor to the kitchen’s drain system. Each dishmachine is supplied with a drain hose. When installed, it will extend from rear side of machine.

There must be an air-gap between machine drain line and floor sink or drain at least times larger than drain hose. If a grease trap is required by code, it should have a

flow capacity of 12 GPM.

Air-gap

24″

1.5x

PLUMBING CHECK After installing the incoming fill line and drain line, turn on the water supply to machine. Check for any leaks and repair as required. All leaks must be repaired before operating machine.

07610-004-45-09-Q

ELECTRICAL POWER

Electrical and grounding conductors must comply with the applicable portions of the CONNECTIONS National Electric Code ANSI/NFPA 70 (latest edition) and/or other electrical codes. The data plate is located on the left-front of the dishmachine. Refer to the data plate for machine operating requirements, machine voltage, total amperage, and serial number.

Disconnect electrical power at the breaker or disconnect switch and tag-out in accordance with procedures and codes. Remove the back panel and set aside. Remove the terminal block box cover. Install 3/4″ conduit into the hole in the bottom of the terminal block box. Route power wires and connect to terminal block. Install the grounding wire onto the lug provided. “DE-OX” or another similar anti-oxidation agent should be used on all power connections.

208/230 V

460 V

On 460 V machine, imbalanced wild leg
goes to L3.

L1 N Ground

3
L1 L2 L3 Ground

MOTOR ROTATION On 3-Phase machines only, correct pump motor rotation must be verified before
machine is operated. Failure to do so can result in damage to machine and

i

components.

1. Follow Filling the Wash Tub section.

2. Using a 7/16 nutdriver, remove front kick panel and keep hardware. Using a

!

phillips screwdriver, remove right dress panel and keep hardware. Leave start

CAUTION

switch wires connected.

CAUTION!
On 3-Phase machines only, correct pump motor rotation must be verified before operation!

3. Locate wash pump motor and identify arrow decal which shows correct motor

rotation.

Arrow Decal

Wash Pump Motor

07610-004-45-09-Q

Motor Fan
Press Start button on right dress panel and immediately open door. 5. This will stop the cycle. Observe rotation of motor fan. 6. If incorrect, disconnect electrical power and reverse L1 and L2 connections at terminal block shown in section above. Replace panels.

VOLTAGE CHECK Apply power to machine. Check incoming power at the terminal block and ensure it corresponds with voltage listed on the data plate. If not, contact a qualified service agency to examine the problem. Do not run machine if voltage is too high or too low.

Advise all proper personnel of the location of the breaker and any problems. Replace the terminal block box cover and tighten-down the screws.

SURROUNDING AREA This is a commercial machine and reaches temperatures that can exceed those
generated by a residential machine. Surrounding countertops, cabinets, flooring material, and subflooring material must be designed and/or selected with these higher temperatures in mind.

CAUTION

CAUTION! Damage to materials not recommended for higher temperatures will not be covered under warranty or by the manufacturer.

TEMPERATURE Temperature setpoints on this machine have been set at the factory. They should only SETPOINTS be adjusted by an authorized service agent.

LEVELING A level machine is important to prevent any damage to machine during operation and to
ensure the best possible results. The machine comes equipped with adjustable bullet feet which can be turned using a pair of pliers. Since this machine is an undercounter unit, it should be leveled as close as possible to the unit’s location before it is pushed under the counter.

CHEMICAL FEEDER Bottom of chemical container cannot be located any higher than 8″ from the floor.

EQUIPMENT

If 6″ or 18″ table stand is used, highest position would be 14″ or 26″ from the floor, respectively.

CAUTION!
Using deionized water or other aggressive fluids will result in corrosion and failure of components and will void the warranty.

CAUTION! Chemical tube must not extend past port into wash chamber.

07610-004-45-09-Q

10

PREPARING This machine is supplied with detergent and rinse-aid chemical feeder pumps. CHEMICAL Locate open ends of chemical tubes with tube stiffeners and place each one in

FEEDER PUMPS appropriate container.
Red Tubing = Detergent · Blue Tubing = Rinse-aid

PRIMING CHEMICAL Chemical feeder pumps need priming when machine is first installed or if chemical FEEDER PUMPS lines have been removed and air was allowed to enter.

CAUTION

NOTICE
Machines with serial numbers before 21A390814 prime differently. Click here to open manual with old instructions.

CAUTION!
Water must be in sump and wash tank before dispensing chemicals.
1. Verify proper chemical tube stiffener inlet is in proper container.
2. To prime detergent pump, press and hold I button until display shows timer. Priming cycle defaults to 70 seconds. Observe wash tank during priming cycle. If too much detergent, press I button to stop priming cycle. If not enough, run priming cycle again.

WARNING
WARNING! Some of the chemicals used in dishwashing can cause chemical burns if they come in contact with skin. Wear protective gear when handling these chemicals.
If any skin comes in contact with these chemicals, immediately follow the instructions provided with the chemicals for treatment.

DETERGENT PRIME
To prime rinse-aid pump, press and hold II button until display shows timer. Priming cycle defaults to 180 seconds.
180
RINSE AID PRIME
Detergent amount might need adjusted depending on water quality and type of detergent. Rinse-aid amount might need adjusted depending on water hardness and results. Refer to next section for instructions on adjusting chemical amounts.

07610-004-45-09-Q

11

OPERATING INSTRUCTIONS

PREPARATION 1. Verify strainers are in place and clean.

CAUTION! Preparation section must be followed before operating machine!

2. Ensure wash and rinse arms are screwed securely in place and end-caps are tight.
3. Verify wash and rinse arms rotate freely.
4. Confirm chemical levels are correct.

POWER UP To energize machine, turn on power at service breaker. The voltage should have been previously verified as correct. If not, voltage must be verified before energizing machine.

FILLING THE 1. Press Power button. WASH TUB

07610-004-45-09-Q

2. Machine will automatically begin fill cycle. 3. Once wash tub is filled, machine displays “HEATING.” 4. Wait for wash temperature to display at least 155 °F and for status to display
“READY” before operating the machine.
155 F
READY CYCLE 1
12

WARE Proper ware preparation helps ensure good results and fewer re-washes. If not done PREPARATION properly, ware might not come out clean and efficiency of the dishmachine will be reduced. Scraps should always be removed from ware before being loaded into a rack. Pre-rinsing and pre-soaking are good ideas, especially for silverware and casserole dishes. Place cups and glasses upside- down in racks so they don’t hold water during the cycle. This machine sanitizes as well as cleans. To do this, ware must be properly prepared before being placed in machine.

WASHING A RACK 1. Follow the Filling the Wash Tub section, ensuring temperature is at least 155 °F OF WARE and status displays “READY.”
155 F
READY CYCLE 1

2. Open door completely. 3. Slide rack into machine.

07610-004-45-09-Q

4. Close door. 5. Choose cycle.

155 F
READY CYCLE 1

Cycle I 100 Seconds Normally-soiled Ware

Cycle II 168 Seconds Heavily-soiled Ware

Cycle III 268 Seconds Extremely-soiled Ware

If Cycle II or Cycle III is chosen, machine will stay in that cycle until another is chosen.

WASHING A RACK 6. Press Start button and machine will begin wash cycle. OF WARE

Temperature shown is minimum required temperature.

155 F
WASHING CYCLE 1

Temperature shown is minimum required temperature.

7. After wash cycle is complete, machine will automatically enter rinse cycle.
180 F
RINSING 10 PSI
8. Once rinse cycle is complete, machine will automatically enter sanitize cycle.

SANITIZE CYCLE 1
9. After sanitize cycle is complete, machine will automatically go back to being “READY.” Open door and remove rack of ware. To start another cycle, load another rack of ware, close door, and push Start button.
155 F
READY CYCLE 1

07610-004-45-09-Q

OPERATIONAL Based on use, strainers might become clogged with soil and debris as the workday INSPECTION progresses. Operators should regularly inspect strainers to ensure they’ve not
become clogged. Clogged strainers will reduce washing capability of machine. Instruct operators to clean out strainers at regular intervals or as required by workload.

SHUTDOWN & 1. Close door and turn machine off by pushing Power button.

CLEANING

155 F

READY

CYCLE 1

2. Drain valve will activate and empty machine of water. 3. When draining stops and display is off, open door and remove and clean
strainers. Set aside.

4. Unscrew wash and rinse arms from manifolds.

5. Verify nozzles and arms are free from obstruction. If clogged, remove end- caps, clean nozzles with a brush, and flush with fresh water.

07610-004-45-09-Q

SHUTDOWN & 6. Replace end-caps and use a screwdriver to ensure they are tight. CLEANING Use a screwdriver to ensure end-caps are tight.

7. Ensure float (located under left strainer) is free of debris.

8. Spray or wipe out interior of machine.

9. Replace wash and rinse arms.

10. Replace strainers and ensure they are laying flat.

07610-004-45-09-Q

11. Use stainless steel polish to clean and protect outside of machine.

DELIMING
In order to maintain machine at its optimum performance level, lime and corrosion
deposits must be removed. The frequency for deliming will be based on water conditions. A deliming solution is available from your chemical supplier. Read and follow all instructions on the label.

If machine is equipped with an SPS and lime is becoming a frequent problem, the cartridge needs to be replaced. To order a replacement cartridge, see the Plumbing Options page.

To delime machine:
1. Remove rinse arms and place in sink with deliming solution (leave for amount of time recommended by chemical supplier).
2. Replace rinse arms. 3. If machine is full of water, close door, press Power button, and allow machine to drain and shut-off. 4. Follow Filling the Wash Tub section of this manual. 5. Open door and add amount of deliming solution recommended by chemical supplier. 6. Close door and press Delime button on display. Status will display “DELIME.”

155 F
DELIME ON

7. Press Start button.

07610-004-45-09-Q

8. Machine will delime, drain, and refill. 9. Wait five minutes, then inspect machine. If machine is not delimed, run again. 10. When clean, press Delime button. Status will display “READY.” 11. Run machine through two regular cycles to remove residual deliming solution. 12. Machine is now ready for normal operation.

DETERGENT Detergent usage and water hardness are two factors that greatly contribute to the CONTROL machine’s operating efficiency. Using the proper amount of detergent can become a source of substantial savings. A qualified water-treatment specialist can determine what is needed for maximum efficiency from the detergent.

· Hard water greatly affects performance of the machine, causing the amount of detergent required for washing to increase. If the machine is installed in an area with hard water, the manufacturer recommends the installation of water treatment equipment.

· Deposited solids from hard water can cause spotting that will not be removed with a drying agent. Treated water will reduce this occurence.

· Treated water might not be suitable for use in other areas of operation and it might be necessary to install a water treatment system for the water going to the machine only. Discuss this option with a qualified water treatment specialist.

· Properly train operators on how much detergent is to be used per cycle. Meet with a water treatment specialist and chemical supplier to discuss a complete training program for operators.

· Water temperature is an important factor in ensuring the machine functions

properly, and the machine’s data plate details what the minimum temperatures must be for the incoming water supply, the wash tank, and the rinse tank. If minimum requirements are not met, it’s possible that dishes will not be clean or sanitized.

· Instruct operators to observe the required temperatures and to report when they fall below the minimum allowed. A loss of temperature can indicate a larger problem.

ENERGY SAVER After no cycle for 30 minutes, Energy Saver Mode initiates and the wash heater MODE thermostat turns off. This conserves energy while the machine is idle. Pushing the start button at any time after Energy Saver Mode is activated turns on the wash heater thermostat, runs a cycle to reheat the wash tank, and resets the timer.

07610-004-45-09-Q

18

MAINTENANCE

PREVENTATIVE MAINTENANCE

PREVENTATIVE The manufacturer highly recommends that any maintenance and repairs not specifically MAINTENANCE discussed in this manual only be performed by qualified service personnel. Performing maintenance on the machine may void a warranty.

By following operating and cleaning instructions in this manual, users should get the most efficient results from the machine. As a reminder, here are some steps to ensure the machine is used properly:

1. Ensure water temperatures match those listed on machine data plate (on front- left of machine).

SSEREIRAILALNNOO. .:: XXXXXXXXXXX

MMOODEDLE: L:WDAISREHFSOTRACRE HUHT-3E0-E WWRIWAWNARSSSIAANHHESSSHMHHHEEEOAMHAHTTTEOOEEEARTARRTOTEERRR TOTTOATLALLOLAODAD

6600HHzz 11PHPH2 W2IRWEIRE

220088VVOOL LTT

4334..1131..31HKKHPWWKKPWW

1111595595…970…079AAAAAA 2244.7.7 AA

223300 VVOOLLTT

4411KKHHWPWP 55 KKWW

12221257161756……..04777407 AAAAAAAA

4000897 C4on0f0or0m8s9t7o NSF Std 3 Conforms to NSF Std 3

ATATTNHTONEMHTOSEOETA:

TWEMSO:
AAERWMSTHIAAEMSNAETHND.IMEDARLEERNIN.CIDNETSSRLREEIECIHNHCAESELTAEARLTTIHOECEREAARDADL(TOSHLEBNIORGAOASHDTEDEDOOSSPONTBENORAAAWTSMTEOPAEDSPDHEORRNAAWWT)EASH MOTOR AND RINSE HEA TER (HIGHEST AMP DRA W)

Intertek Int4er0t0e0k897 ConCfCooron4mnfCSo0sforott0mdonrm0sfCUots82Lro2m9tCo.2s7SSUANttoLdoC.S912St6d1A8921 Std C22.2 No.168

OPERATING PARAMETERS MINIMUM WAOSPHERTAETMINPG P ARAMETERS MMINIINMIMUMUMWRASINHSTEEMTEP MP MMININIM.UINMCROINMSIENTGEMWPATER TEMP MWINA. ISNHCOCMYICNLGE WTIAMTEER TEMP WRAISNHSCEYCCLYECTLIME ETIME RIWNSAETCEYRCLFELTOIMWEPRESSURE WATER FLOW PRESSURE

155°F 118505°°FF 111800°°FF 8011S0E°CF 890 SSEECC 190SPESCI
10 PSI

CAUTION: IF THIS MACHINE IS CONNECTED TO A CIRCUIT PROTECTED BY FUSES,

CAUTSIOEN: IOF TNHLISYMA3CH0IANE INS COONNN- TECI TMEDE TOD EALCAIRYCUIFT UPRSOETECTOERD BYOFVUESERS C, U R R E N T

U SPEROOTENCLTYION3 .0 A N O N – T I M E D E L A Y F U S E O R O V E R C U R R E N T PROTECTION. ATTENSION: SE CONNECTER A UN MINIMUM D’ALIMENTATION 30 AMPERES

ATTDEENLSAIOI FNUS:IBSLEE DCE OTYNPNEECNTOEN-RTEMA PSU ONU LMAINPIRMOUTMECTDIO’ANLICMOENTRTAETLIEOSN SU3R0INTAEMNPSEIRTEESS.

DELAMIIFNUIMSIUBLME DCEIRTCYUPEITNAOMN-PTAECMIPTSYOU LA

PROTECTION CONTRE LES SURINTENSITES.

MIN@IM20U8MVCOIRLCTUSI:T 26.A0MAPMAPCSITY @20@82V3O0LVTOS:L2T6S.0: 2A8.M0PASMPS

@230 VOLTS: 28.0 AMPS MAXIMUM OVERCURRENT PROTECTION

MA@XI2M0U8MVOOVLETRSC:U3R0RAENMTPPSROTECTIO

@20@82V3O0LVTOS:L3T0S:A3M0PASMPS

@230 VOLTS: 30 AMPS

Made in the USA JacMkasdoeninWtWheSU,SIAnc 6J2a0c9ksNonUWSWHSW, YIn2c5E 6209 NGrUaSy,HKWYY4072354E
099G((066r5a00y-660),)0K554Y22-343-24-99-0787797935D54

2. Remove as much soil as possible from ware before loading into racks.

CAUTION
CAUTION! Do NOT beat strainers to remove soil and debris!

3. Ensure strainers are in place, laying flat in tub, and free of soil and debris before operating machine. To clean strainers, wipe out with a rag and rinse under a faucet. For stubborn debris, a toothpick can be used. Do not beat strainers on waste cans; once bent, they will not work properly.

4. Ensure all wash and rinse arms are secure in machine before operating.

07610-004-45-09-Q

PREVENTATIVE 5. Do not overfill racks. MAINTENANCE
6. Ensure glasses are placed upside-down in the rack.

7. Ensure all chemicals being injected into machine have been verified at correct concentrations.
8. Clean machine at end of every workday (see Shutdown and Cleaning section).
9. If hard water is present, install an SPS into water line connecting to machine (see Water Supply Connections section).
10. Always contact a qualified service agency when a serious problem arises.
11. Follow all safety procedures, whether listed in this manual or put forth by local, state, or national codes/regulations.

07610-004-45-09-Q

TROUBLESHOOTING

PROGRAMMING

MODEL CONFIRMATION
To access programming, machine should be on and not in cycle.
Programming buttons (up-arrow, down-arrow, and select) are hidden on display and are shown below as red outlines.

A transparent guide to locating the programming buttons is included with machine, behind the kick panel. Lay the guide over the display and press where indicated.

Factory Setup (Model Selection) 1. Press and hold I and III buttons until “Program” starts flashing (2­3 seconds).

CAUTION! Machine will not operate properly with wrong program number!

2. Press select button.
3. Use up-arrow or down-arrow button to change program number to correct number in table, based on model.

PROGRAM SEE TABLE

Pgrm #

Model

8

UH30-E

9

UH30-E-SEER

4. Press select button. 5. “Program” will flash. 6. Press delime button to exit.
150 F
READY CYCLE 1

07610-004-45-09-Q

21

TROUBLESHOOTING

PROGRAMMING USER SETUP

To access programming mode, machine should be on and not in cycle.

A transparent guide to locating the programming buttons is included with machine, behind the kick panel. Lay the guide over
the display and press where indicated.

Programming buttons (Up-arrow, Down-arrow, and Select) are hidden on display and are shown below outlined with red dots.
1. Press and hold Up-arrow and Down-arrow buttons until “Setup” flashes (2­3 seconds).

SETUP
2. Display will then change to “Version” and show firmware versions of the I/O module and display.

3. Use Up-arrow button to cycle through categories (will be flashing).

· Language · Temperature Scale · Wash Temperature · Boost Temperature

· Wash Offset · Rinse Offset · Boost Offset · Spare Offset

LANGUAGE

07610-004-45-09-Q

4. Press Select button to choose category to change. · Regardless of category, Steps 5­7 remain the same.
5. Use Up-arrow button to change options (will be flashing). Numerical options are shown in top window.

LANGUAGE ENGLISH
6. Press Select button to accept changes. 7. Press Delime button to exit.

FAULT CODES

DISPLAY SHOWS
“F1 Service needed,” “No water in Booster”
“F2 Service needed,” “Check booster thermostat”
“F3 No water in wash tank,” “Check inlet water and door” “F4 Service needed,” “Check incoming power”

POSSIBLE CAUSES
1. Low or no water pressure. 2. Faulty inlet valve or fill relay. 3. Contactor to booster heater not turning off. 4. Faulty temperature input (P12) on IO module. 5. Faulty temperature probe (T3). 6. Faulty float switch allows heaters to operate with no water in tub.
1. Contactor to booster heater not turning off. 2. Faulty temperature input (P12) on IO module. 3. Faulty temperature probe (T3).
1. Malfunction of fill solenoid or fill relay. 2. Door is open, which inhibits fill mode. 3. Faulty door switch. 1. Incoming power not properly connected. 2. L3 is missing (3-phase machines only).

REMEDY 1. Verify incoming water pressure is 10 ± 2 PSI.
2. Verify that fill relay is supplying voltage to fill solenoid. Replace faulty component.
3. Check for welded contacts. Verify that output from IO module turns off when above the set temperature.
4. Substitute a 1.2 k resistor for T3, and verify that booster heater turns off. If not, replace IO module.
5. Verify that the booster-probe resistance is correct with respect to temperature (see table on pg. 24). If not, replace T3.
6. Replace float switch. 1. Check for welded contacts. Verify that output from IO module turns off when above the set temperature.
2. Substitute a 1.2 k resistor for T3, and verify that booster heater turns off. If not, replace IO module.
3. Verify that the booster probe resistance is correct with respect to temperature (see table on pg. 24). If not, replace T3. 1. Replace faulty component.
2. Close door to activate door switch.
3. Replace or adjust door switch. 1. Check connections to heater.
2. Verify that L3 is present and connected properly.

“F5 Service needed,” “Check booster thermostat and high limit”

1. Faulty temperature input (P12) on IO module.
2. Faulty temperature probe (T3). 3. Faulty high-limit switch. 4. Faulty booster heater. 5. Booster-heater contactor not energizing.

1. Substitute a 1.8 k resistor for T3, and verify that booster heater turns on. If not, replace IO module.
2. Verify that T3 resistance is consistent with the table on pg. 24. If not, replace T3.
3. Replace high-limit switch.
4. Check booster heater for proper resistance. Replace if incorrect.
5. Verify that drive voltage to contactor coil is present during a call for heat and that contactor closes. If voltage is present, replace contactor. If voltage is not present, check wiring.

07610-004-45-09-Q

DISPLAY SHOWS POSSIBLE CAUSES

1. Low or no water pressure.

2. Faulty inlet valve or fill relay.

3. Contactor to wash heater not turning off. “F6 Service needed,” “No water in wash tank”

4. Faulty temperature input (T1) on IO module.

5. Faulty temperature probe (T1).

6. Faulty float switch allows heaters to operate with no water in tub. “F7 Service needed,” “Check wash tank thermostat”

1. Contactor to wash heater not turning off.
2. Faulty temperature input (P10) on IO module.
3. Faulty temperature probe (T1).

“F8 No water in wash tank,” “Check inlet water and door”
“F9 Service needed,” “Check incoming power”

1. Malfunction of fill solenoid or fill relay. 2. Door is open, which inhibits fill mode. 3. Faulty door switch. 1. Incoming power not properly connected. 2. L3 is missing (3-phase machines only).

1. Faulty temperature input (T1) on I/O module.

“F10 Service needed,” “Check wash tank thermostat and high limit”

2. Faulty temperature probe (T1). 3. Faulty high-limit switch. 4. Faulty wash heater.

5. Wash-heater contactor not energizing.

“F11 Service needed,” “Check wash tank thermostat” Faulty temperature probe (T1).

REMEDY 1. Verify incoming water pressure is 10 ± 2 PSI.
2. Verify that fill relay is supplying voltage to fill solenoid. Replace faulty component.
3. Check for welded contacts. Verify that output from IO module turns off when above the set temperature.
4. Substitute a 1.2 k resistor for T1, and verify that wash heater turns off. If not, replace IO module.
5. Verify that T1 resistance is correct with respect to temperature (see table on pg. 24). If not, replace T1.
6. Replace float switch. 1. Check for welded contacts. Verify that output from IO module turns off when above the set temperature.
2. Substitute a 1.2 k resistor for T1, and verify that wash heater turns off. If not, replace IO module.
3. Verify that T1 resistance is correct with respect to temperature (see table on pg. 24). If not, replace T1. 1. Replace faulty solenoid or fill relay.
2. Close door to activate door switch.
3. Replace or adjust door switch. 1. Check connections to heater.
2. Verify that L3 is present and connected properly. 1. Substitute a 1.8 k resistor for T1, and verify that wash heater turns on. If not, replace I/O module.
2. Verify that T1 resistance is correct with respect to temperature (see table on pg. 24). If not, replace T1.
3. Replace high-limit switch.
4. Check wash heater for proper resistance. Replace if incorrect.
5. Verify that drive voltage to contactor coil is present during a call for heat and that contactor closes. If voltage present, replace contactor. If voltage not present, check wiring.
Replace probe that connects to P10.

07610-004-45-09-Q

DISPLAY SHOWS
“F12 Service needed,” “Check booster thermostat”

POSSIBLE CAUSES Faulty temperature probe (T3).

“F13 Communication error,” “Check 6-pin cable”

1. Loose connection in 6-pin cable between display board and I/O module.
2. Faulty 6-pin cable between display board and I/O module.
3. Faulty communication port on I/O module or display board.

REMEDY
Replace probe that connects to P13.
1. Fully disconnect 6-pin cable at each end, and reconnect each end until a click is heard.
2. Inspect for broken wire or unseated terminal by gently pulling on each wire at each end of the cable. Reseat any loose terminals by inserting it fully into the housing using long-nosed pliers. Replace cable if broken wire is found.
3. Temporarily substitute a verified good display board, and check if F13 message recurs. If so, repeat substitution with a good I/O module.

“F14 Service needed,” “Check incoming water pressure or pressure switch”

1. Low or no water pressure.
2. Faulty pressure switch.
3. Faulty fill valve or fill valve not receiving power.

1. Verify correct PSI. 2. Replace pressure switch. 3. Check continuity and replace if faulty.

“F15 Sanisure violation”

1. Faulty booster heater. 2. Faulty heater contactor.

1. Check amperage on heater. 2. Check voltage on contactor coil and L1 and L2 legs.

“F16 LLC violation” Faulty or corroded probe.

Clean or replace probe.

“F17 Excessive inlet temp”

Inlet water supply too hot.

Ensure inlet water supply is at required temperature.

RESISTANCE-TO-TEMPERATURE VALUES

07610-004-45-09-Q

R (k) 11.58 10.37 9.30 7.78 3.05 2.54 2.18 1.58 1.45 1.33 1.16 0.96

°F 69.8 75.2 80.6 89.6 140.0 150.8 159.8 179.6 185.0 190.4 199.4 212.0

WARNING

WARNING! Inspection, testing, and repair of electrical equipment should only be performed by qualified service personnel. Certain procedures in this section require electrical tests or measurements while power is applied to machine. Exercise extreme caution at all times. If test points are not easily accessible, disconnect power, attach test equipment, and reapply power to test. When replacing electrical parts, disconnect power at circuit breaker.

OBSERVATION POSSIBLE CAUSE

Water overflow 1. Clogged drain. from bottom of door.

2. Machine not level.

3. Excessive inlet pressure.

REMEDY 1. Remove obstruction.
2. Level machine or increase height to the front.
3. Install pressure regulating valve or adjust if one is present. Ensure flow meets data plate specification.

4. Detergent foaming.

4. Reduce detergent quantity.

5. Wash or rinse arm end-cap missing. 5. Replace.

Wash motor doesn’t operate on wash.

1. Loose or broken wires. 2. Defective Start button. 3. Defective motor contactor.

1. Reconnect or replace wires in motor. 2. Adjust button or replace. 3. Replace.

Little or no water coming through the rinse assemblies.

1. Limed-up rinse heads or piping. 2. Low water pressure.

1. Delime rinse heads.
2. Increase pipe size to machine. Adjust pressure regulating valve.

07610-004-45-09-Q

WARNING

WARNING! Inspection, testing, and repair of electrical equipment should only be performed by qualified service personnel. Certain procedures in this section require electrical tests or measurements while power is applied to machine. Exercise extreme caution at all times. If test points are not easily accessible, disconnect power, attach test equipment, and reapply power to test. When replacing electrical parts, disconnect power at circuit breaker.

OBSERVATION POSSIBLE CAUSE

Rinse water runs 1. Defective plunger in solenoid valve.

continuously with breaker

2. Defective diaphragm in solenoid valve. turned off.

REMEDY 1. Replace plunger.
2. Replace diaphragm. Wash

1. Water level low.

temperature not within range. 2. RTD setpoint too low.

1. Check water level. If low, run new fill cycle. 2. Adjust setpoint.

3. Defective RTD.

3. Replace RTD.

4. Wash heater defective.

4. Replace heater element.

5. Defective heater contactor R1.

5. Replace contactor.

Rinse temperature not within range.

1. RTD is defective.
2. Incoming rinse water does not meet minimum criteria indicated machine data plate.

3. Rinse heaters damaged.

4. Setpoint screens set low.

Machine doesn’t drain when power button is pressed.

1. Drain clogged. 2. Defective drain valve.

1. Replace if necessary. 2. Adjust as required.
3. Check amperages. Replace if necessary. 4. Adjust rinse tank setpoint. 1. Remove obstruction. 2. Replace.

Incorrect water pressure displayed during Fill or Rinse.

1. Water turned off. 2. Transducer disconnected. 3. Pressure transducer defective.

1. Turn water on. 2. Verify wiring. 3. Replace pressure transducer.

07610-004-45-09-Q

PARTS

1 2
3

TERMINAL BLOCK BOX, 208/230 V
4 5
6 7
8

ITEM 1 2
3 4 5 6 7 8

QTY 1 1 1 1 1 2 2 1 1

07610-004-45-09-Q

DESCRIPTION Power Connection Decal Terminal Block Box Terminal Box Cover (Not Shown) Strain Relief Terminal Block Track Terminal Block Locknut, 10-24 Hex with Nylon Insert Decal, L1, N Ground Lug

PART NUMBER 09905-011-47-35 05700-004-36-47 05700-003-27-70 05975-003-37-56 05700-000-43-60 05940-500-02-19 05310-373-01-00 09905-011-62-72 05940-200-76-00

TERMINAL BLOCK BOX, 460 V

1 2

3

ITEM 1 2
3 4 5 6 7 8

QTY 1 1 1 1 1 3 2 1 1

07610-004-45-09-Q

DESCRIPTION Power Connection Decal Terminal Block Box Terminal Box Cover (Not Shown) Strain Relief Terminal Block Track Terminal Block Locknut, 8-32 Low Profile Decal, L1, L2, L3 Ground Lug

4 5 6
7
8
PART NUMBER 09905-011-47-35 05700-004-44-79 05700-004-44-80 05975-210-03-00 05700-004-44-72 05940-500-02-19 05310-004-23-83 09905-101-12-66 05940-200-76-00

KICK PANEL

1

5

6

4

7 8

2 3

10 5
9
11

ITEM
1 2 3 4 5 6 7 8 9 10 11

QTY
1 2 2 1 4 1 4 1 4 1 1

DESCRIPTION Complete Kick Panel Assembly Kick Panel Locknut, 6-32 Hex with Nylon Insert P-clamp, 1/4″ ID Bushing, Snap Locknut, 10-24 Hex with Nylon Insert Cover, Display Nut, Thumb 6-32 Nylon PCB, Digital Display Spacer, Unthreaded, 9/32″ Nylon Panel & Membrane Switch Assembly Communication Cable

07610-004-45-09-Q

PART NUMBER 05700-004-41-87 05700-004-41-86 05310-373-03-00 05975-002-61-42 05975-210-09-00 05310-373-01-00 05700-004-46-05 05310-002-83-12 05700-004-19-47 05975-004-47-89 05700-004-58-72 05700-004-33-64

NOTICE
208-230 V machines with serial numbers before 22E406186 have a universal timer. Click here to open earlier manual.

CONTROL PANEL, 208/230 V

13

24

1

23 25

12

15

16 2
17 18

22 21 3

4

5

20

3

L2

L1

16 11 17 26

7 28

9 27
6
8*

14

27

10

19*

29
30
33 32 31

07610-004-45-09-Q

ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

QTY 3 1 2 5 16 16 1 1 1 4 1 1 6 9 1 5 3 2 1 2 2 1 1 1 1 1 6 2 2 1 1 1 1

CONTROL PANEL, 208/230 V

DESCRIPTION Contactor, 30 A, 240 VAC I/O Module End Bracket, Terminal Separator, Terminal Block Terminal Block, Single Level Tag, Marking Power Supply Peri-pump Assembly Din Rail, 5 3/4″ P-clamp, 1/4″ ID Bushing, 1 1/8″ Bracket, Control Panel Screw, 10-32 x 1/2″ Fastener, 10-32 Fuse, Time-delay 8 A, 250 V Nut, Plated 6-32 Screw, 6-32 x 3/8″ Screw, 10-32 x 1″ Peri-pump Assembly Jumper Bars, 4-Pole Jumper Bars, 3-Pole Jumper Bars, 2-Pole Screw, 10-32 x 1/2″ Decal, Ground Fuser Holder, One Only Relay, 10 A, 240 VAC Locknut, 10-24 Hex with Nylon Insert Screw, 6-32 x 1/2″ Stiffener, Chemical Tube Chemical Port Assembly Tubing, Blue, 1/4″ Tubing, Red, 1/4″ Tubing, Clear, 1/8″

PART NUMBER 05945-002-74-20 05945-004-44-63 05999-004-90-66 05999-004-90-67 05999-004-90-68 05999-004-90-72 05950-004-81-79 05700-004-71-63 05700-021-72-75 05975-002-61-42 05975-210-08-00 05700-004-96-19 05305-002-80-88 05340-111-58-10 05920-004-85-54 05340-118-04-00 05305-002-25-91 05305-002-19-42 05700-005-00-29 05999-004-41-80 05999-004-90-71 05999-004-41-79 05305-011-39-36 09905-011-86-86 05920-002-42-13 05945-111-89-75 05310-373-01-00 05305-004-23-63 05700-002-66-49 05700-004-30-86 04720-604-11-00 04720-601-12-00 04720-111-58-09

*See Chemical Feeder Pumps section for peri-pump components.

07610-004-45-09-Q

CONTROL PANEL, 460 V

NOTICE
208-230 V machines with serial numbers before 22E406186 have a universal timer. Click here to open earlier manual.

13

24

1

35 23 25

12

15

16 2
17 18

22 21 3

34

4

5

20

3

16 11 17 26

L2

L1

7 28

9 27
6
8*

14

27

10

19*

29
30
33 32 31

07610-004-45-09-Q

CONTROL PANEL, 460 V

ITEM

QTY

DESCRIPTION

1

3

Contactor, 240 VAC

2

1

I/O Module

3

2

End Bracket, Terminal

4

5

Separator, Terminal Block

5

16

Terminal Block, Single Level

6

16

Tag, Marking

7

1

Power Supply

8*

1

Peri-pump Assembly

9

1

Din Rail, 5 3/4″

10

4

P-clamp, 1/4″ ID

11

1

Bushing, 1 1/8″

12

1

Bracket, Control Panel

13

6

Screw, 10-32 x 1/2″

14

9

Fastener, 10-32

15

1

Fuse, Time-delay 8 A, 250 V

16

5

Nut, Plated 6-32

17

3

Screw, 6-32 x 3/8″

18

2

Screw, 10-32 x 1″

19*

1

Peri-pump Assembly

20

2

Jumper Bars, 4-Pole

21

2

Jumper Bars, 3-Pole

22

1

Jumper Bars, 2-Pole

23

1

Screw, 10-32 x 1/2″

24

1

Decal, Ground

25

1

Fuser Holder, One Only

26

1

Relay, 10 A, 240 VAC

27

6

Locknut, 10-24 Hex with Nylon Insert

28

2

Screw, 6-32 x 1/2″

29

2

Stiffener, Chemical Tube

30

1

Chemical Port Assembly

31

1

Tubing, Blue, 1/4″

32

1

Tubing, Red, 1/4″

33

1

Tubing, Clear, 1/8″

34

1

Dinrail, 7 3/4″

35

1

Overload Relay, 1.7­2.3 A

*See next section for peri-pump components.
07610-004-45-09-Q

PART NUMBER 05945-005-05-99 05945-004-44-63 05999-004-90-66 05999-004-90-67 05999-004-90-68 05999-004-90-72 05950-004-81-79 05700-004-71-63 05700-021-72-75 05975-002-61-42 05975-210-08-00 05700-004-96-19 05305-002-80-88 05340-111-58-10 05920-004-85-54 05340-118-04-00 05305-002-25-91 05305-002-19-42 05700-005-00-29 05999-004-41-80 05999-004-90-71 05999-004-41-79 05305-011-39-36 09905-011-86-86 05920-002-42-13 05945-111-89-75 05310-373-01-00 05305-004-23-63 05700-002-66-49 05700-004-30-86 04720-604-11-00 04720-601-12-00 04720-111-58-09 05700-002-79-13 05945-004-97-95

CHEMICAL FEEDER PUMPS

ITEM 1 2 3 4 5 6 7 8 9 10

8
QTY 2 4 1 2 8 4 1 2 1 1

015702 06-004-71-6103 7 9 3

4

05700-005-00-29

5

DESCRIPTION Pump Housing Screw, 8-32 x 3/8″ Phillips Roller, Plastic Pump Cover Screw, 6-32 x 3/4″ Phillips Screw, 8-32 x 1/2″ Phillips Tube, Squeeze, 8″ Motor, 14 RPM Roller, Plastic Tube, Squeeze, 9″

PART NUMBER 04320-111-37-09 05305-011-37-07 04320-002-82-28 04320-111-37-08 05305-011-37-05 05305-011-37-06 05700-003-22-89 04320-011-63-33 04320-111-65-27 05700-011-65-21

07610-004-45-09-Q

10
07610-004-45-09-Q

Complete Door Assembly 05700-004-36-53
13 16
9

DOOR
6

14
11 21
8

14
16 5 12 7

15 20
7
16

17 18 11 14 19
8
36

PARTS

ITEM

QTY

1

1

2

2

3

2

4

2

5

12

6

1

7

2

8

1

9

1

10

1

11

1

12

2

13

1

14

2

15

1

16

6

17

1

18

1

19

6

20

12

21

1

DESCRIPTION Outer Door Weldment Screw, 10-32 x 1/4″ Bolt, 1/4-20 x 3/8″ Hex Washer, 1/4-20 ID Fastener, 10-32 Door Handle Stop, Door Hinge Hinge, Left Hinge, Right Inner Door Baffle, Door Hinge Spacer Switch Assembly Retaining Plate Channel, Door Seal Screw, 1/4-20 x 1 1/2″ Hex Head Gasket, Door L Gasket Clamp Pop Rivet, 1/8″ x 3/8″ Screw, 10-32 x 1/2″ with Washer Bracket, Door Magnet

DOOR
PART NUMBER 05700-004-52-86 05305-173-01-00 05305-274-20-00 05311-174-01-00 05340-111-58-10 05700-003-26-62 05700-003-32-55 05700-003-32-71 05700-003-32-72 05700-003-33-21 05700-003-33-38 05700-003-33-42 05700-003-34-80 05700-011-44-37 05700-003-55-49 05305-274-23-00 05330-004-36-05 05700-004-36-56 05320-003-06-98 05305-002-32-37 05700-004-52-73

07610-004-45-09-Q

MISCELLANEOUS DOOR COMPONENTS

Parts are not shown to scale in relation to each other.

1 2

10

9

11

8

7

6

4

3

5

ITEM 1 2 3 4
5 6 7 8 9 10 11

QTY 1 2 1 1
2 2 4 2 2 1 1 1 1

DESCRIPTION
Switch Mounting Plate Assembly Door Spring Cover, Left Hinge Weldment Cover, Right Hinge Weldment Hinges secured with Locknut, 1/4-20 Hex with Nylon Insert O-ring Latch Spring Latch Nut Locknut, 6-32 Hex with Nylon Insert Screw, 6-32 x 1/4″ Door Switch Door Switch Bracket Door Switch & Bracket Assembly Complete Switch Mount Assembly

PART NUMBER 05700-003-33-54 05700-003-32-85 05700-004-36-80 05700-004-36-81 05310-374-01-00 05330-003-32-34 05700-003-32-32 05700-003-32-33 05310-373-03-00 05305-171-01-00 05930-003-31-44 05700-003-31-43 05700-003-32-21 06401-004-47-76

07610-004-45-09-Q

UH30-E-SEER DOOR INTERLOCK

Complete Door Interlock Assembly 05700-004-99-58

6

10

11
4 2
1

12

7

2

5
1
NOTICE
208-230 V machines with serial numbers before 22E406186 have a different door interlock. Click here to
open earlier manual.

5 1 8

ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13
07610-004-45-09-Q

QTY 6 6 1 1 2 1 1 1 2 1 2 2 1

DESCRIPTION Screw, 6-32 x 5/8″ Locknut, 6-32 Hex with Nylon Insert Link, Interlock Connector Pin, Interlock Switch, Interlock Synchronous Gearmotor, 6 RPM, 230 V, 60 Hz Interlock Guide Interlock Cam Shoulder Screw, 10-32 Bracket, Interlock Screw, 10-32 x 1/2″ Locknut, 10-32 with Nylon Insert Set Screw, 6-32 x 1/4″

13
9
3
PART NUMBER 05305-011-39-85 05310-373-03-00 05700-004-71-37 05700-004-71-49 05930-004-71-36 06105-004-70-04 05700-004-71-50 05700-004-71-39 05700-004-71-40 05700-004-99-63 05305-011-39-36 05310-373-02-00 05305-004-71-42
4

WASH
6 5
5

19
07610-004-45-09-Q

3
16 15 17

5 5

1 5
8 9

2
7 18
11 16
15

13 14 13
10 13 12 13
15

ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17
18
19

QTY 1 1 1 2 5 2 4 1 1 1 1 1 4 1 3 2 1 1 1 1 1

DESCRIPTION Wash Arm Assembly Motor Support Wash Halo Pipe Clamp Wash Arm End- cap Screw, 1/4-20 x 1/2″ Locknut, 1/4-20 Hex with Nylon Insert Manifold Gasket Wash Hub Wash Motor Discharge Hose, 7/8″ x 8″ Hose, 1 1/4″ x 2 3/4″ Clamp, 1 1/16″ to 2″ Hose, Manifold Bottom Clamp, 13/16″ to 1 1/2″ Hosebarb, 90-Degree, 3/4″ x 1″ Drain Valve Assembly, 208/230 V Drain Valve Assembly, 115 V (for 460 V Machine) Bracket, Drain Valve Support, 208/230 V Bracket, Drain Valve Support, 460 V Drain Hose

WASH
PART NUMBER 05700-021-39-23 05700-004-40-61 05700-004-42-21 05700-000-35-06 05700-003-31-59 05307-011-36-96 05310-374-01-00 05330-002-34-77 05700-004-43-04 See Motors page. 05700-004-43-76 05700-011-44-48 04730-719-18-00 05700-001-22-92 04730-719-06-09 04730-011-65-87 04730-003-33-64 04730-003-34-60 05700-004-35-85 05700-004-42-01 04720-004-32-00

07610-004-45-09-Q

MOTORS

6 7

4
1 2 3 5

ITEM 1 2 3 4 5 6 7

QTY 1 1 1 1 1 1 1

DESCRIPTION Pump and Motor, 208/230 V Pump and Motor, 460 V
Seal Plate, 208/230 V Seal Plate, 460 V
Case O-ring, 208/230 V Case O-ring, 460 V
Mechanical Seal, 208/230 V Mechanical Seal, 460 V
Impeller Assembly, 208/230 V Impeller Assembly, 460 V
Pump Casing 208/230 V Pump Casing 460 V
Case Capscrew

PART NUMBER 06105-004-35-22 06105-003-52-78
05700-002-81-87 05700-002-06-22
05330-002-81-83 05330-002-87-02
05330-002-34-22 05330-002-87-16
05700-002-81-86 05700-002-06-19
05700-002-85-01 05700-002-06-20
05305-002-81-88

07610-004-45-09-Q

1

3 2

RINSE

4

ITEM 1 2 3
4
5 6 7

4 3

QTY 1 1 4 2 2 2 2 2

DESCRIPTION Complete Rinse Manifold Assembly Pipe Clamp Rinse Arm End-cap (includes o-ring) Complete Rinse Arm Assembly Rinse Arm Bearing Assembly, Rinse Arm O-ring (included in item #5) Retaining Ring

3
3 Rinse Arm Bearing Kit 06401-004-57-50
5
6 7
PART NUMBER 05700-004-40-58 05700-000-35-06 05700-004-34-62 05700-004-39-39 05700-004-38-75 05700-004-54-71 05330-002-60-69 05340-112-01-11

07610-004-45-09-Q

PLUMBING OPTIONS
SHOCK ABSORBER (WATER ARRESTOR) OPTION

NOTICE UH30-E-SEER has a water arrestor as standard equipment. See the UH30-E- SEER Plumbing page.
Nipple, 1/2″ NPT, Brass 04730-207-15-00

Water Arrestor, 1/2″ 06685-100-05-00
Tee, 1/2″ x 1/2″ x 1/2″ 04730-211-27-00
Water Arrestor Repair Kit (Plunger & O-ring) 06401-003-06-23

PRESSURE REGULATING VALVE (PRV) OPTION

NOTICE
UH30-E-SEER has a PRV as standard equipment. See the UH30-E-SEER Plumbing page.

Pressure Regulating Valve, 1/2″ 04820-100-04-07

SCALE PREVENTION SYSTEM (SPS) OPTION

SPS System 04730-003-28-03
NOTICE Must be installed vertically. The provided bracket is secured to the wall. Observe proper inlet/outlet water directions (flow directions are molded into the top of the head). Line pressure should be released
before changing cartridges. Machine should be delimed before installation.

Replacement Cartridge (inspect at least every 6 months)
04730-003-28-04
Replacement Test Strip (Not Shown)
06401-003-28-06

07610-004-45-09-Q

UH30-E PLUMBING
Complete Inlet Plumbing Assembly, 208/230 V 05700-004-09-03
Complete Inlet Plumbing Assembly, 115 V (for 460 V Machine) 05700-004-44-40
7

6

5 1
8*

4 2 3

*Item not included in part number of complete plumbing assembly and must be ordered separately.

07610-004-45-09-Q

UH30-E PLUMBING

ITEM
1
2 3 4 5 6 7 8*

QTY
1
1 1 1 1 1 1 1

DESCRIPTION Valve, 1/2″, 208/230 V Valve, 1/2″, 115 V (for 460 V Machine) Union, 1/2″ x 1/2″ Brass Nipple, 1/2″ Close Brass Nipple, 1/2″ x 4″ NPT Brass Adapter, 1/2″ Fitting, Male Elbow, 1/2″ Hose Adapter Bracket, Plumbing Support

PART NUMBER 04810-003-71-56 04810-003-71-55 04730-003-62-44 04730-207-15-00 04730-207-04-00 04730-011-59-53 04730-406-31-01 04720-004-24-68 05700-004-56-19

*Item not included in part number of complete plumbing assembly and must be ordered separately.

07610-004-45-09-Q

UH30-E-SEER PLUMBING
Complete SEER Plumbing Assembly, 208/230 V 05700-004-63-79
Complete SEER Plumbing Assembly, 460 V 05700-004-78-45
7
CONNECTS TO COLD WATER INLET ON SEER SYSTEM
6

CONNECTS TO HOT

WATER OUTLET ON

10

SEER SYSTEM

8 4

9

5

07610-004-45-09-Q

2 11*

1

3

*Item not included in part number of complete SEER plumbing assembly and must be ordered separately.

UH30-E-SEER PLUMBING

ITEM
1
2 3 4 5 6 7 8 9 10 11*

QTY
1
1 1 1 1 1 1 1 1 1 1

DESCRIPTION Inlet Plumbing Assembly, 208/230 V Inlet Plumbing Assembly, 115 V (for 460 V Machine) Pressure Regulating Valve, Dial-set Booster Tank Discharge Assembly Tee, 1/2″ Brass Nipple, 1/2″ Close Brass Water Hammer Arrestor, 1/2″ SEER Inlet Plumbing Assembly Elbow, 90-degree, 1/2″ Street Brass Adapter, Double Male, 3/4-11.5 x 1/2-14 Inlet Hose Assembly Bracket, Plumbing Support

PART NUMBER 05700-004-53-98 05700-004-78-48 05700-004-94-35 05700-004-55-97 04730-211-27-00 04730-207-15-00 04730-004-58-56 05700-004-60-46 04730-206-08-00 04720-004-51-55 05700-004-71-02 05700-004-56-19

*Item not included in part number of complete SEER plumbing assembly and must be ordered separately.

07610-004-45-09-Q

1
2 7

RINSE PLUMBING
Complete Rinse Plumbing Assembly 05700-004-43-02

8e 8d

5

8c

8b

6
8f 8a
8g
8h

8 9

3 4

07610-004-45-09-Q

ITEM 1
2
3
4
5
6
7
8 8a 8b 8c 8d 8e 8f 8g 8h
9

QTY 1
1
1
1
1
1
1
1 1 1 2 1 1 1 2 1
1

DESCRIPTION
Vacuum Breaker, 1/2″ Brass
Hose, Red, 1/2″ ID, 19″
Nipple, 1/2″ x 3″, Brass
Elbow, 1/2″, 90-degree, Brass
Elbow, 90-degree
Pipe, 4 3/4″, Copper
Adapter, 1/2″
Complete Rinse Injector Assembly Rinse Injector Only Gasket, Rinse Injector Screw, 1/4-20 x 1″ Check Valve Fitting, Outlet Elbow Nut, Tube, 1/8″ Plug, 1/8″ Brass Pressure Transducer
Harness, Transducer

RINSE PLUMBING
PART NUMBER 04820-003-06-13 05700-004-33-84 04730-004-20-10 04730-011-42-96 04730-406-32-01 05700-002-91-02 04730-002-64-68 05700-004-43-86
09515-004-22-73 05330-003-75-91 05305-011-81-58 04820-111-51-14 04820-111-51-18 04730-011-59-45 04730-209-07-37 05945-004-17-01 05700-004-33-62

07610-004-45-09-Q

16 15 14 13
12
1 2

RINSE TANK

7 3

17 4

11 9 10
8 7
07610-004-45-09-Q

5
6
ITEM
1
2
3
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

QTY 1 1 1 1 1 4 4 1 2 1 1 1 1 1 1 1 1 1 1 1

DESCRIPTION Rinse Tank, 208/230 V Rinse Tank, 460 V Heater Gasket Rinse Heater, 5.45 kW, 208-230 V Rinse Heater, 5.45 kW, 460 V Lockwasher, Split 5/16″ Nut, Hex 5/16-18 Cable, Temperature Probe Thermistor Probe, 4″ with 18″ Cable Fitting, 1/4″, Brass Nut/Sleeve Plug, 1/4″ Brass Union, 1/2″ x 1/2″ Brass Elbow, 90-degree, 1/2″ Street Brass Nipple, 1/2″ Close Brass Fitting, 1/2″ x 1/4″ Tee, 1/2″ Brass Nipple, 1/2″ x 3″ Brass Elbow, 90-degree, 1/2″ Brass Thermostat, Rinse Tank High-limit (Not Shown) Cable, Temperature Probe

*Not used on UH30-E-SEER. See Item #1 in UH30-E-SEER Plumbing section.

RINSE TANK
PART NUMBER 05700-004-41-88 05700-004-44-46 05330-011-47-79 04540-004-45-12 04540-121-65-99 05311-275-01-00 05310-275-01-00 05700-004-33-23 06685-004-34-58 05310-924-02-05 04730-209-01-00 04730-003-62-44 04730-206-08-00 04730-207-15-00 05700-004-36-74 04730-211-27-00 04730-004-20-10 04730-011-42-96 05930-004-33-12 05700-004-33-58

07610-004-45-09-Q

SEER SYSTEM

Complete SEER System Assembly, 208/230 V 05700-004-63-06
Complete SEER System Assembly, 115 V (for 460 V Machine) 05700-004-64-72
NOTICE Machines with serial numbers before 19G376587 have an older version of the SEER System. Click here to open manual with the older version.

5

17

14

4

3

2
19 6 5 1

STICKY SIDE

15

9

12

10

7 13

8 16 20 11

12 18

07610-004-45-09-Q

ITEM
1
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

QTY
1
1 1 1 5 1 2 2 1 1 1 12 8 1 2 1 1 1 1 1

DESCRIPTION Motor, Fan, 208/230 V Motor, Fan, 115 V (for 460 V Machine) Wheel, Blower Bracket, Bearing Boot Bushing and Housing Assembly Locknut, 10-24 Hex with Nylon Insert Bracket, Motor Adjustment Grommet, Push-in, 3/4″ ID Bracket, Enclosure Filler Plate Diversion Plate Upper Shield Heat Exchanger, 3/8″ Tubes Locknut, 1/4-20 Hex with Nylon Insert Screw, 6-32 x 1/2″ Condenser Assembly Bolt, 1/4-20 x 1/2″ Plumbing, SEER Inlet Bracket, Bearing Hard Stop Lower Shield Spacer, 1/2″ OD 1/4″ ID Nylon, Black Gasket, Exchanger to Tub

SEER SYSTEM
PART NUMBER 05999-004-63-31 05999-004-64-71 05999-004-59-13 05700-004-50-94 03120-004-50-88 05310-373-01-00 05700-004-58-81 05330-004-59-14 05700-004-58-93 05700-004-59-04 05700-004-58-98 04420-004-58-96 05310-374-01-00 05305-004-23-63 05700-004-58-94 05305-274-02-00 05700-004-60-46 05700-004-67-53 05700-004-63-04 03120-004-95-13 05330-004-59-16

NOTICE Machines with serial numbers before 19G376587 have an older version of the SEER System. Click here to open manual with the older version.

07610-004-45-09-Q

1 2

3

6″ Stand Install Instructions

10

STANDS & PANELS

4

5

6

11

ITEM 1 2 3 4 5 6 7 8 9 10 11
11a

QTY 1 1 4 4 1 1 4 4 4 4 1
3

DESCRIPTION 6″ Stand Assembly Stand 6″ Leg Bullet Foot 18″ Stand Assembly Stand Bullet Foot 18″ Leg Cross Brace Cross Member Bracket Back Panel
Edge Guard, Back Panel (Not Shown)

07610-004-45-09-Q

7

9

8

18″ Stand Install Instructions

PART NUMBER 05700-003-34-24 05700-002-88-82 05700-021-61-10 05340-108-01-03 05700-003-34-25 05700-002-88-82 05340-108-01-03 05700-002-89-47 05700-003-25-90 04730-003-25-89 05700-004-58-14
05330-002-83-04

4

1

2 3

ITEM 1 2 3 4 5 6 7 8 9 10 11

QTY 1 1 4 1 1 2 1 1 1 2 1

07610-004-45-09-Q

DESCRIPTION Shroud, Left Frame, Left Adjustable Foot Shroud, Top Frame, Right Plug, Shroud Panel, Bottom Support, Strainer Left Support, Strainer Right Strainer Shroud, Right

FRAME
6
5

11 9

8

7

10

PART NUMBER 05700-003-37-04 05700-003-31-91 05340-002-71-71 05700-003-37-06 05700-003-31-90 05700-003-32-50 05700-004-44-54 05700-004-40-52 05700-004-40-53 05700-004-09-43 05700-004-36-82

MISCELLANEOUS PARTS
Parts are not shown to scale in relation to each other.

1

2

3

11 10

4a
460 V Drain Water Tempering Kit Install Instructions

8 7

208-230 V Drain Water Tempering

Kit Install Instructions

6

4b

Wash Heater Replacement Instructions

9
5

ITEM 1 2 3 4a 4b 5 6 7
8
9 10 11
07610-004-45-09-Q

QTY 1 1 1
1
1 1 1
1
1 1 1

DESCRIPTION Rail, Left Rack Rail, Right Rack Splash Shield Drain Water Tempering Kit, 208-230 V Drain Water Tempering Kit, 460 V Dual Float Switch Thermistor Probe, 4″ with 18″ Cable Probe Fitting, 1/4″ Brass Wash Heater, 4 kW, 208-230 V Wash Heater, 4 kW, 460 V Gasket, Wash Heater (Not Shown) Thermostat, Wash Tank High-limit with Compression Fitting Transformer, 460 V Transformer Bracket, 460 V

PART NUMBER 05700-031-37-89 05700-031-37-88 05700-003-33-51 06401-004-60-64 06401-004-56-12 06680-121-70-16 06685-004-34-58 05310-924-02-05 04540-003-99-44 04540-004-12-29 05330-011-61-34 05930-004-33-15 05950-004-71-04 05700-004-44-55

SCHEMATICS

NOTICE
Machines with serial numbers before 22E406186 have a different schematic.
Click here to open earlier manual.

208/230 V, 50/60 HZ, 1-PHASE
SCHEMATIC

07610-004-45-09-Q

NOTICE
Machines with serial numbers before 22E406186 have a different schematic.
Click here to open earlier manual.

460 V, 60 HZ, 3-PHASE
SCHEMATIC

07610-004-45-09-Q

NOBLE UNDERCOUNTER DISH MACHINES
Noble Warewashing · Lancaster, Pennsylvania www.nobleproducts.biz.
For Service Call 1-888-800-5672 UH30-E Manual · 07610-004-45-09-Q

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>