Noble House 70289 Natural Fabric Upholstered Bench Instruction Manual
- June 3, 2024
- Noble House
Table of Contents
70289 Natural Fabric Upholstered Bench
Instruction Manual
Assembly Instructions
Caution: You must read this before you proceed
Parts List
Label | Picture | Description | QTY |
---|---|---|---|
A | Left leg | 1 | |
B | Right Leg | 1 | |
C | Top | 1 |
Hardware
Label | Picture | Description | QTY |
---|---|---|---|
① | Bolt( M8*64mm) | 9 | |
② | Flat Washer | 9 | |
③ | Allen Wrench | 1 |
Assembly Preparation
Before Beginning Assembly:
| • Read instructions, cover to cover-
---|---
• Have 2 adults on hand for assembly-
• Do not assemble on flooring or carpet-
• Assemble on a clean non-marring surface (packing foam)-
• Save all packaging until finished-
Assembly Steps
Overview
This Bench has multiple parts and may require up to 30 mins to assemble. To
give you an overview of the Bench parts, the above picture is to help you put
the various parts into perspective. Please read through the instructions here
below to familiarise the parts and steps before assembly.
Step 1
Unpack and place all parts on a clean, non-marring surface.
Step 2
NOTE: Each leg is numbered. Please match according to respective markings.
Place the Top (C) with its one side face skywards onto a clean, soft surface
to avoid any scratches or damages to the product.
Align the tenon of the Top (C) into the Mortise of the Left Leg (A) as shown
above. Then, affix the Top (C) with the Left Leg (A) by using Short blots
(①)+Flat Washer(②) and Allen Wrench (③)
DO NOT FULLY TIGHTEN BOLTS.
Step 3
Then continue position Top (C) as shown in the picture above. Align the wooden
dowel into the positions in the Legs.
Then, affix the Right Leg (B) with the Top (C) by using Short Bolts (①)+Flat
Washer(②) and Allen Wrench (③)
DO NOT FULLY TIGHTEN BOLTS.
Step 4
With the help of your partner, turn the Bench to rest on Top (C) so that the
Right Leg (B) is now facing skywards.
Repeat the same process by affixing Bolts (①), and (②) to designated points.
DO NOT FULLY TIGHTEN BOLTS.
Step 5
Turn the Bench right side up.
Place the Bench on a LEVEL SURFACE.
Inspect it and make sure all parts are adequately connected.
Gently and gracefully, sit on the Bench.
This would help to align all the parts at all the joint areas.
Then get off the Bench, and in a sequential manner, proceed to tighten all
blots.
To tighten the blots at the base of the Top, secure assistance from your adult
partner(s).
You may be required to turn the Bench, to gain easy access to the secure
points.
Turn the Bench in a synchronized manner.
CAUTION 1: When tightening these blots, tighten them sequentially.
DO NOT tighten any blots fully and then towards the next one. This would
cause the frame to warp.
If there are still wobbles, loosen the blots and execute this same process.
IF Bench IS NOT STABLE, IT COULD LEAD TO DAMAGING THE
PRODUCT.
Ensure all bolts are fully locked into position.
The Bench is ready to be used.
Caution 2: This Bench can only be used on a flat, level surface.
Care & Maintenance
| • Furniture may scratch floors. We recommend using furniture pads to protect
your floors.
---|---
• Do not put hot items directly on the furniture surfaces.
• Do not clean furniture with harsh cleansers or polish.
• Do not place furniture under direct sunlight.
• Do not place furniture near heating or cooling vents.
• Do not write on furniture without a padded barrier to protect the surface.
• Do not place furniture outside For indoor use only.
• Not for commercial use. For residential use only.
• Stains may be removed with the mild soap solution and a damp cloth.
• Children should not climb or jump on the furniture.
• Dust and pick up spills using a clean, non-colored, lint-free cloth.
Noble
House Home Furnishings LLC
Documents / Resources
|
Noble House 70289 Natural Fabric Upholstered
Bench
[pdf] Instruction Manual
70289, Natural Fabric Upholstered Bench, 70289 Natural Fabric Upholstered
Bench, Fabric Upholstered Bench, Upholstered Bench, Bench
---|---