Lumineux UK 430156-SD Rutland Bulkhead Instruction Manual

: June 11, 2024
: Lumineux UK

Table of Contents

BOX CONTENTS
TOOLS REQUIRED
DISPOSAL
WARRANTY
PRODUCT TEMP SPECIFICATION
MICROWAVE SENSOR SETTINGS
RUTLAND BULKHEAD DIMENSIONS
STEP DIM DRIVER SETTINGS
Documents / Resources

Lumineux UK 430156-SD Rutland Bulkhead Instruction Manual

READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLATION KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

IMPORTANT:
This product must be installed by a qualifi ed electrician or competent person, and in accordance with current building and IET wiring regulations.

BOX CONTENTS

This lighting fi xture has been properly packed to avoid damage during transit. Before commencing with the installation carefully inspect the luminaire to confi rm there is no damage. DO NOT INSTALL if any damage has occurred to the fi xture or any of its components.

Light Fitting
Instruction Manual
Fixing Kit

TOOLS REQUIRED

Drill
Screwdriver
Cable

Manby Business Park, Manby, Lincolnshire, LN11 8UT Lumineux is a B&T Associates Ltd company
Symbol

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION.

WARNING: Risk of electric shock! Isolate the mains power before proceeding.

Turn off the mains power before performing inspections, installation, or removal
Verify that the supply voltage is correct by comparing it with the luminaire label information
It is the installers responsibility to ensure installation is suitable for the total load of the luminaire(s). The supply cable, fuses/circuit brakers must be correctly rated for the electrical load and considering for any transient inrush currents that may occur
Do not perform insulation strength or resistance tests on installed luminarie(s) connected

Remove the diffuser by gently twisting anti-clockwise
Twist the locking tab to loosen and remove the geartray.
Drill appropriately sized holes through your chosen mounting points in the base
Install grommet to your chosen cable entry and pierce, making a hole just large enough to make a tight fi t around the incoming mains cable. Carefully thread cable through grommet and secure fi tting in place
Wire as per diagram (5). Select colour temperature (Please see overleaf for instructions on how to set all sensor versions and emergency)
Replace the geartray and twist the locking tab to secure in place, then refi t the diffuser and then re-connect the mains supply

DISPOSAL

Disassembly instructions for end of life disposal available on website. Disposal of Electronic Equipment WEEE Directive 2002/96/EC This product falls within the scope of the Waste Electrical & Electronic

Equipment Directive (WEEE), which means the product should not be disposed of as normal household waste. Please recycle where facilities exist or check with your

Local Authority. RoHS – All components and materials used in this product are RoHS 2002/95/EC compliant.

Specifications may change from time to time. The information contained in this leaflet is for guidance only and should not be considered as always accurate and should be treated as not representative.

WARRANTY

This luminaire is warranted for a period of 5 years from the date of purchase**. The backup battery pack in the emergency version is warranted for a period of 24 months. The warranty could be invalidated should the light fitting not be installed according to these instructions, outside the scope of the specification or the product has been altered or tampered with in any way. Please see website for terms and conditions.

PRODUCT TEMP SPECIFICATION

Standard -20 to +40ºC
Emergency 0 to +30ºC
Revision 2 – October 2022

MICROWAVE SENSOR SETTINGS

**** This determines the effective range of the motion.

Note that reducing the sensitivity will also narrow the detection range.

Hold Time Duration: This determines the time the fitting remains at 100% illumination following motion detection.

Daylight Setting: This setting holds off the 100% light output should there be sufficient daylight.

STANDARD ON/OFF SENSOR

DETECTION AREA	HOLD TIME	DAYLIGHT SENSOR
1	2	3
I	ON	ON
II	–	ON
III	ON	–
IV	–	–
V	–	–
VI	–	–

RUTLAND BULKHEAD DIMENSIONS

Part No. Description	Watts	L (mm)	W (mm)	H (mm)	Weight
Rutland430156 3CCTBulkhead	12W	330	330	110	0.8Kg

DIMENSIONS

STEP DIM DRIVER SETTINGS

DETECTION AREA

| 1|
---|---|---
I| ON| 100%
II| –| 50%

HOLD TIME

| 2| 3| |
---|---|---|---|---
I| ON| ON| 5S|
II| ON| –| 90S| I
III| –| ON| 3min| II
IV| –| –| 10min| III

DAYLIGHT SENSOR

| 4| 5|
---|---|---|---
I| ON| ON| Disable
II| ON| –| 30 Lu
III| –| ON| 15 Lux
| –| –| 5 Lux

STAND-BY PERIOD

| 6| 7|
---|---|---|---
I| ON| ON| 0s
II| ON| –| 30s
III| –| ON| 10min
IV| –| –| +∞

STAND-BY DIM LEVE

| 8|
---|---|---
I| ON| 10%
II| –| 25%

* OUTPUT CURRE

| S1| S2| S3
---|---|---|---
450mA| ON| ON| ON
400mA| ON| –| ON
380mA| –| –| ON
350mA| –| ON| –
320mA| ON| –| –
300m| –| –| –

Do not change output current unless instructed or this will void warranty

Installation Engineers Contact Details:| Luminaire Reference / Location
---|---
Name:| Tel:|
Luminaire Details:| Full Recharge Duration 24 Hours| Emergency Duration 3 Hours| Lamp Type LED
---|---|---|---
ROUTINE TEST RECORD

Wiring instructions for units equippedan with EMERGENCY function

Emergency lighting luminaries must be installed and maintained in accordance with the emergency lighting standard BS 5266-1

Connect incoming earth cable to ‘Earth’ terminal on connector block.
Connect incoming neutral cable to ‘Neutral’ terminal on connector block.
For the emergency unit to work correctly, please ensure that an uninterrupted permanent live feed is present and is connected directly to the ‘Permanent Live’ terminal of the mains terminal block. Please ensure there are no switches, PIRs etc within the permanent live feed, constant switching of the emergency pack could result in premature battery failure.
Connect incoming switched live cable to the terminal marked “Switched Live”
NOTE: If there is no switch live feed and the unit has a microwave sensor, simply bridge across from the “Permanent Live” to the Switch Live” on the mains terminal block.
There should be a loose flying lead connected to the battery. This needs to be attached to the flying lead from the emergency control unit.
Following power up the green LED indicator should illuminate to indicate charging. If power to the unit is disrupted or isolated, the unit indicating green LED will switch off, triggering the emergency LEDs to illuminate.
Please allow 24 hours charge before first emergency tes