Milwaukee Tool 58-22-1426d1 Bolt Full Face Shield Instruction Manual

Milwaukee Tool 58-22-1426d1 Bolt Full Face Shield Instruction Manual

USER INSTRUCTIONS

WARNING

Read all safety warnings and instructions provided. Save all warnings

and instructions for future reference.

Failure to follow these instructions and warnings may result in serious and permanent eye injury, including blindness or death.

• Before using this product in an industrial setting, refer to ANSI Z87.1 (in the United States) or CSA 3 (in Canada), your supervisor, or a safety specialist to insure that you are wearing proper protection. Some operations may require machine guards, goggles, face shields, special filter lenses, or other safety equipment.
• This product helps provide limited eye protection from light to moderate impact hazards, such as metal or wood chips and small flying objects. This face shield is impact-resistant but NOT
• Protective devices do NOT provide unlimited protection. Eye and face protective devices are not substitutes for machine guards and other engineering controls. Personal eye and face protective devices alone should not be relied on to provide complete protection against hazards (such as fragmenting grinding wheels, exploding devices, ), but should be used in conjunction with the machine guards, engineering controls, and sound manufacturing and personal safety practices.

• To reduce the risk of injury, always wear ANSI Z87.1 goggles or

spectacles along with these products.

• Do NOT use for sports, simulated combat games (e.g., paintball), or recreation such as target shooting and archery.

• Always use both hands to install and remove this product. Do NOT use unless securely attached to

• Examine this product frequently and replace it immediately if there is any sign of damage. Do NOT use shield if signs of wear are visible including breakage, gouges, cracks, dents, chalky appearance, discoloration or loss of color, or craze Do NOT make any modifications to this product.

• Wash polycarbonate shields with water and pat dry with a lens cloth. Wash mesh shields with mild soap and water, rinse, and dry with a Do NOT use ammonia, alkaline cleaners, abrasive cleaning compounds, or solvents when cleaning shields. Use of certain solvents may lower the impact resistance of the shields.

• Do NOT use for protection against chemical mists, sprays, splashes, or

• Do NOT use mesh shield for protection against sand or

• Special Purpose (Tinted) lenses are NOT for use where filter lenses are required.

• Do NOT use near an open flame. Do NOT use for burning, cutting, welding with torches, or electric (arc) welding. Do NOT use this product for protection against laser Eyewear with tinted lenses offers limited protection against sun glare or other light sources.

• Do NOT use this face shield if it has sustained an Dispose of it

immediately, even if damage is not visible.

• Do NOT alter, pierce, modify, or engrave the face
• Do NOT tamper with assembly
• Do NOT alter the face shield to fit attachments in any way not recom- mended by the manufacturer.
• Store in a clean, dry area, out of direct sunlight
• Do NOT store face shield in direct sunlight, including the dashboard or rear window shelf of a vehicle, or in extreme heat over 120 ° F (49 ° C). Exposure to direct sunlight and heat over time can lessen the ability of the face shield to withstand impact and

Mesh light transmittance: 62.1%
Polycarbonate UV Information: These lenses block over: 99.9% UVA 315-380nm
99.9% UVB 285-315nm
99.9% UVC 200-285nm

Only use this MILWAUKEE Face/Mesh Shield with the recommended No Brim Helmets.

FUNCTIONAL DESCRIPTION

1. Helmet adapter tab
2. Cover
3. Face shield
4. Adapter release tab

SYMBOLOGY

SPECIFICATIONS

Compatible with…………………………………..MILWAUKEE NO BRIM HELMETS
Replacement Brim………………………………………….. Cat. No. 48-73-1449
Clear Shield…………………………………………………… Cat. No. 48-73-1421
Gray Shield……………………………………………………. Cat. No. 48-73-1426
Metal Mesh Shield………………………………………….. Cat. No. 48-73-1431
Replacement Shields
Compatible with……………. MILWAUKEE NO BRIM HELMET FACE SHIELDS
Clear Shield 5 pk ……………………………………………. Cat. No. 48-73-1444
Clear Shield 10 pk ………………………………………….. Cat. No. 48-73-1445
Gray Shield 5 pk…………………………………………….. Cat. No. 48-73-1446
Gray Shield 10 pk…………………………………………… Cat. No. 48-73-1447
Replacement Metal Mesh
Metal Mesh Shield 5 pk …………………………………… Cat. No. 48-73-1434
Metal Mesh Shield 10 pk …………………………………. Cat. No. 48-73-1435

ASSEMBLY

Attaching/Removing Face Shield and Brim

1. To install the shield assembly, the adapter tabs (left and right) will engagein the forward most accessory slots of the helmet. Slide the adapter tabs down through the front accessory slots on the helmet until they securely “click” into position.
2.  To remove the shield assembly, turn the helmet over to access the inside of the helmet. Locate the release tabs where they protrude to the underside of the helmet. Press the release tab on both sides and push upwards through the accessory slots of the helmet.
3. Pull adapters (left and right) and face shield away from helmet.

Replacing the Face Shield

1. Remove the face shield assembly from the helmet.
2. On the side covers, just below the MILWAUKEE logo, locate the lock tab at the back edge of the cover identified by the unlock . 3. Pull the lock tab out away from the face shield. Once it is visible the lock tab and the mating lock feature of the shield are no longer overlapping, rotate the cover component forward without rotating the shield (Fig. 1).
3. NOTE: Push the face shield inwards, while pulling the locking tab out, then rotate forward. Pushing on the face shield is critical for removal.
4. With the cover rotated forward, approximately 90 degrees, the shield can be pulled down to separate from the pivot assembly of the brim.
5. To reinstall a shield to the brim, reverse the procedure. The curved leading edge of the shield as it is inserted in the pivot of the brim ensure the leading edge is slid beneath the lip on the mating surface of the pivot (Fig. 2 and 3).
6. Once the leading edge is fully inserted into the brim pivot, rotate the cover plate backward to the locked position until it securely “clicks” (Fig 4).
7. After the shield is installed, cycle the shield to the full up and full down positions twice to ensure all components are fully engaged. If the shield would dislodge and separate during this step, an error was made during the re-installation. Repeat the shield installation steps again. Ensure the proper position and full engagement of the shield leading edge where it seats in the pivot and cover components.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>