DSC HSM2108 8-Zone Expander Module Instruction Manual

DSC HSM2108 8-Zone Expander Module

8-Zone Expander Module
This Installation sheet shall be used in conjunction with the Installation Manual of the DSC equipment to which HSM2108 is connected or powered from (e.g. alarm controller, power supply, etc.). The HSM2108 module can be used to extend up to 8 hardwired input zones on the compatible DSC Alarm Control Panel (Alarm Panel), models HS2016, HS2032, HS2064, and HS2128.

General

HSM2108 may be installed in the same metallic cabinet as the alarm controller/power supply (model Power UC1, PC5003C) or in a separate enclosure (PC4003C). Internal and/or external wiring for the HSM2108 shall be routed, supported, clamped or secured in a manner that reduces the likelihood of

1. (a) excessive strain on wire and terminal connections
2. (b) loosening of terminal connections, and
3. (c) damage of conductor insulation.

Specifications

• Temperature range : -10°C to + 55°C (0°C to +49°C for UL/ULC listed systems)
• Relative Humidity : 93% non condensing
• Input rating : 10.8 to 12.5VDC/130mA (provided by the alarm controller or separate power supply)
• Board current draw : 40mA
• Board dimensions : 45mm x 92mm
• VAUX output ratings : 10.8 to 12.5Vdc.
• Resettable fuse (PTC) used on circuit board instead of replaceable fuses
• Maximum wire length from alarm panel : 1,000™/305m (22 AWG)

Terminal Descriptions

• TMP – Used to tamper the cabinet in which the HSM2108 is mounted. Connect a normally closed (NC) switch across TAM and BLK. If the tamper is not being used connect a piece of wire across TAM and BLK to remove the trouble condition. There is a built-in tamper switch on the expander module located in the top left corner of the circuit board. If the cabinet in which the HSM2108 is mounted has the hardware required to depress this tamper switch, do not connect anything to the TAM terminal.
  NOTE : Tamper protect is required for UL/ULC commercial/residential burglary installations.

• AUX+ – Used to provide power for devices. Maximum current draw is not to exceed 100 mA. Connect the positive lead of powered devices to VAUX and the negative to

• BLK or any COM terminal.

• CORBUS – The 4-wire Corbus connection is used by the panel to communicate with the module. Connect the RED, BLK, YEL and GRN terminals to the Corbus terminals on the HS2016, HS2032, HS2064, or HS2128 main control.

• Z1 to Z8 – Wire the zones according to the description found in the control panel Installation Manual.

NOTE : UL/ULC installations require single end-of-line or double end-of- line configuration with 5600Ω resistors.

Enclosures

The HSM2108 can be installed in the metal enclosures listed below. Tamper protection switches can be installed on all enclosures, including door opening protection and/or removal from the mounting position. Doors can be secured using screws or keylock.

• Model PC5003C (removable door)
• Model PC5003C (hinged door)
• Model Power UC1
• Model PC4003C
• Model CMC-1
• Model PC4050CAR (commercial burglary)
• Model PC4050CR (ULC–S559)

NOTE : Use PC4003C, PC5003C, CMC-1, PC4050CAR, or PC4050CR for UL/ULC installations

Automatically Enrolling on the Alarm Panel

When a HSM2108 is enrolled on the alarm panel, it will take the next available bank of 8 zones. To enroll the HSM2108 follow these steps:

1. Ensure that the system is not powered.
2. Connect the HSM2108 to the Corbus.
3. Power up the system.
4. Enter section [902] [000] and wait 1 minute.
5. Enter section [903] [102]to verify that the module is supervised.
6. Define the zones in section [001].
7. Configure zone attributes in section [002]
8. Add the zones to the appropriate partition in sections [201]-[208].

Manually Enrolling on the Alarm Panel

When a HSM2108 is enrolled on the alarm panel, it will take the next available bank of 8 zones. To enroll the HSM2108 follow these steps:

1. Ensure that the system is not powered.
2. Connect HS2108 to the Corbus.
3. Power up the system.
4. Enter section [902] [001].
5. Enter the module serial number.
6. Enter section [903] [102]to verify that the module is supervised.
7. Define the zones in section [001].
8. Configure zone attributes in section [002]
9. Add the zones to the appropriate partition in sections [201]-[208].

Status LED

The HSM2108 is equipped with a status LED to indicate the current status of the module. If the HSM2108 is operating correctly, the status LED will flash briefly every 10 seconds. When a trouble condition is pres-ent, the status LED will display a series of flashes then remain blank for 1.7 seconds. The number of flashes between blank periods indicates the trouble condition present as outlined in the table below.

LIMITED WARRANTY

Digital Security Controls (DSC) warrants that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workman-ship under normal use and that in fulfilment of any breach of such warranty, DSC shall, at its option, repair or replace the defective equipment upon return of the equipment to its factory. This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control of DSC such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper application of the equipment.

The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of DSC. This warranty contains the entire warranty. Digital Security Controls neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. In no event shall DSC be liable for any direct or indirect or consequential damages, loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product.

Warning : Digital Security Controls recommends that the entire system be completely tested on a regular basis. However, despite frequent test-ing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected.

IMPORTANT – READ CAREFULLY: DSC SOFTWARE PURCHASED WITH OR WITHOUT PRODUCTS AND COMPONENTS IS COPYRIGHTED AND IS PURCHASED UNDER THE FOLLOWING LICENSE TERMS

This End-User License Agreement (EULA) is a legal agreement between You (the company, individual or entity who acquired the Software and any related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd. (DSC), the manufacturer of the integrated security systems and the developer of the software and any related products or components (HARDWARE) which You acquired. If the DSC software product (SOFTWARE PRODUCT or SOFTWARE) is intended to be accompanied by HARDWARE, and is NOT accompanied by new HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The SOFT-WARE PRODUCT includes computer software, and may include associated media, printed materials, and “online” or electronic documentation. Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement is licensed to You under the terms of that license agreement. By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally to be bound by the terms of this EULA, even if this EULA is deemed to be a modification of any previous arrangement or contract. If You do not agree to the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no right to use it.

SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.

1. GRANT OF LICENSE This EULA grants You the following rights:

2. (a) Software Installation and Use – For each license You acquire, You may have only one copy of the SOFTWARE PRODUCT installed.

3. (b) Storage/Network Use – The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used concurrently on or from different computers, including a workstation, terminal or other digital electronic device (“Device”). In other words, if You have several workstations, You will have to acquire a license for each workstation where the SOFTWARE will be used.

4. (c) Backup Copy – You may make back-up copies of the SOFTWARE PRODUCT, but You may only have one copy per license installed at any given time. You may use the back-up copy solely for archival purposes. Except as expressly provided in this EULA, You may not otherwise make copies of the SOFTWARE PRODUCT, including the printed materials accompanying the SOFTWARE.

5. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS

6. (a) Limitations on Reverse Engineering, Decompilation and Disassembly – You may not reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. You may not make any changes or modifica-tions to the Software, without the written permission of an officer of DSC. You may not remove any proprietary notices, marks or labels from the Software Product. You shall institute reasonable measures to ensure compliance with the terms and conditions of this EULA.
   (b) Separation of Components – The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be separated for use on more than one HARDWARE unit.
   (c) Single INTEGRATED PRODUCT – If You acquired this SOFTWARE with HARDWARE, then the SOFTWARE PRODUCT is licensed with the HARDWARE as a single integrated product. In this case, the SOFTWARE PRODUCT may only be used with the HARDWARE as set forth in this EULA.
   (d) Rental – You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post it on a server or web site.
   (e) Software Product Transfer – You may transfer all of Your rights under this EULA only as part of a permanent sale or transfer of the HARDWARE, provided You retain no copies, You transfer all of the SOFTWARE PRODUCT (including all component parts, the media and printed materials, any upgrades and this EULA), and provided the recipient agrees to the terms of this EULA. If the SOFTWARE PRODUCT is an upgrade, any transfer must also include all prior versions of the SOFTWARE PROD-UCT.
   (f) Termination – Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply with the terms and conditions of this EULA. In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its component parts.
   (g) Trademarks – This EULA does not grant You any rights in connection with any trademarks or service marks of DSC or its suppliers.

7. COPYRIGHT
   All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to any images, photographs, and text incorpo-rated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies of the SOFTWARE PRODUCT, are owned by DSC or its suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT. All title and intellectual property rights in and to the content which may be accessed through use of the SOFTWARE PRODUCT are the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights not expressly granted under this EULA are reserved by DSC and its suppliers.

8. EXPORT RESTRICTIONS
   You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, or entity subject to Canadian export

9. CHOICE OF LAW
   This Software License Agreement is governed by the laws of the Province of Ontario, Canada.

10. ARBITRATION
    All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in accordance with the Arbitration Act, and the parties agree to be bound by the arbitrator’s decision. The place of arbitration shall be Toronto, Canada, and the language of the arbitration shall be English.

11. LIMITED WARRANTY

12. (a) NO WARRANTY – DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.

13. (b) CHANGES IN OPERATING ENVIRONMENT – DSC shall not be responsible for problems caused by changes in the operating characteristics of the HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.

14. (c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK – IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

15. (d) DISCLAIMER OF WARRANTIES – THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PER-SON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CON-CERNING THIS SOFTWARE PRODUCT.

16. (e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY – UNDER NO CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUEN-TIAL OR INDIRECT DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPI-TAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY. WARNING: DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail to perform as expected.EN CERTIFICATION

The model HSM2108 zone expander has been certified by Telefication according to:

• EN50131-1 :2006+A1:2009
• EN50131-3 :2009 for Grade 2, Class II.

The term IC before the radio certification number signifies that the Industry Canada technical specifications were met. This Class B digital apparatus complies with Canadian ICES-003. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause inter-ference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

FCC COMPLIANCE STATEMENT

CAUTION : Changes or modifications not expressly approved by DSC could void your authority to use this equipment.

This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in any residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to television or radio reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient the receiving antenna
• Relocate the alarm control with respect to the receiver
• Move the alarm control away from the receiver
• Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet pre-pared by the FCC useful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.

©2014 Digital Security Controls Toronto, Canada www.dsc.com Tech. Support: 1-800-387-3630 (Canada & U.S.), 905-760-3036

References

• DSC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>