HABYS Electric Massage Oil Heater User Manual

HABYS Electric Massage Oil Heater

Thank you for choosing HABYS products. Proper use and maintenance of the product ensures full satisfaction of its use for many years.

Product Information

The HABYS Electric Oil Warmer allows you to heat and maintain a comfortable temperature for massage oil. The plastic bottle with a dispenser reaches a temperature of approximately 40 degrees Celsius within 40 minutes (after a few automatic device turn-ons). The built-in thermostat maintains a steady temperature for the oil.

• Oil container
• Electric warmer
• Indicator light
• On/Off button

Technical Specifications

• Power supply: 230 VAC / 50 Hz
• Maximum temperature: 40°C
• Rated power: 42W-50W
• Warmer dimensions: 14 cm wide, 15 cm high, cable length 150 cm
• Bottle dimensions: 5×21 cm, volume of 250 ml

Usage Instructions

1. Place the warmer on a stable, level surface and plug it in.
2. Fill the attached bottle with massage oil and place it inside the warmer.
3. Set the dispenser to the open position (i.e. oil flows out when dispenser is pressed).
4. Turn on the power button and make sure the indicator light is on. Wait for 30-40 minutes to reach the desired temperature.

Warranty Conditions

• The warranty period for the HABYS Electric Oil Warmer is 2 years. The warranty covers defects arising from the product itself and does not cover mechanical damage or damage caused by improper use.
• The buyer is responsible for installation and maintenance of the product. The warranty is valid only if the product is repaired by an authorized service center or by the manufacturer.
• The warranty does not cover color differences between exposed and non-exposed parts to sunlight, wear and tear, presence of stains or rings from oily or coloring substances, or permanent discoloration from dyeing agents such as blue jeans ink.
• The buyer loses warranty rights in case of unauthorized repairs, modifications, or misuse of the product. The manufacturer is not responsible for any damages caused by using the product outside of its intended purpose.

Thank you for choosing HABYS products and congratulations on your purchase. We recall that the proper use and maintenance of the products ensures full satisfaction of their use for many years.

User Manual number : 020/2022
User Manual release date: 24.03.2022

APPLICATION

Oil warmer allows to heat and keep comfortable temperature of massage oil. Oil in a plastic bottle with dispenser (after a few automatic turn off / turn on) reaches a temperature of approx. 40 C within 40 minutes. Warmer keeps the constant temperature of oil using the built-in thermostat.

CONSTRUCTION OF OIL WARMER

OPERATION

1. Place the heater on a stable, level surface and plug it in.
2. Fill the attached bottle with dispenser (1) with massage oil and place it in the bottle warmer (2). Set the dispenser in open mode (i.e. when you press the dispenser, oil flows out).
3. Turn on the power button (4) and make sure that the control lamp (3) is on. Wait 30 to 40 minutes for the oil to be warmed up. The warmer will turn on and off automatically several times and the temperature of the oil will keep increasing until it reaches a temperature of about 40 C.
4. Before use, check the temperature of the oil to avoid burns. First presses the dispenser will extract the oil clearly cooler (coming from the tube). After a few presses an oil with a pleasant temperature of around 40 C will flow out.
5. The switched-on warmer will keep a temperature of about 40 C. If you plan more massages with warm oil during a day, you can leave the warmer on. The warmer thermostat will prevent the oil from overheating.
6. Turn the device off using the button (4) after you finish using the warmer

EXPLOITATION REMARKS

1. Put the oil into the bottle (1) before putting it into the warmer (2).
2. Do not pour liquids directly into the warmer.
3. Before use, make sure that the warmer and bottle are dry inside.
4. Do not submerge the warmer in water.
5. Do not turn on the warmer without making sure that the bottle is in the correct position and is full at least half of its volume. If the bottle is overfilled, the liquid will leak out while warming. If the bottle is closed, it may be deformed during cooling.
6. After use, turn off the warmer and disconnect the power plug from the socket.
7. Keep the device away from children and pets.
8. Use only PP bottles. PET bottles will melt or can be deformed by hating due to its low melting point.

TECHNICAL DATA

• Power: 230 VAC / 50 Hz
• Maximum temperature : 40 oC
• Maximum power : 42W-50W
• Warmer dimension: 14 cm – width, 15 cm – height, 150 cm – cable length
• Oil bottle dimension: 5×21 cm, volume 250 ml

WARRANTY CONDITIONS

1. For the purposes of the guarantee:
2. “Manufacturer” refers to HABYS Spółka z ograniczoną odpowiedzialnością (Limited Liability Company) with its registered seat in Jasło, ul. Produkcyjna 16, 38-200 Jasło, entered into the Register of Entrepreneurs kept by the District Court in Rzeszów, XII Commercial Division of the National Court Register, with the assigned KRS number: 0000513317, with the share capital in the amount of PLN 10.750.000 (ten million seven hundred fifty thousand zlotys), the capital has been fully paid up, NIP: 6852208438, REGON: 180186290.
3. “Buyer” refers to the final Buyer of the equipment, manufactured by the Manufacturer, including both the consumer and the entrepreneur.
4. “Distributor” refers to an entity that, under an agreement with the Manufacturer, sells the Equipment in a designated area.
5. “Authorized Service Centre” refers only to a service held by the Manufacturer or a service indicated by the Manufacturer and held by its Distributor,
6. “Equipment” refers to a movable item, manufactured by the Manufacturer, being the subject of the sales and to which the said warranty applies.
7. The manufacturer ensures good quality and efficient operation of the equipment for which the warranty card has been issued, for the period of: 2 years.
8. The guarantee repair does not include the activities provided for in the manual, which the Buyer is obliged to perform on his own (installation of the Equipment, maintenance of the Equipment, etc.).
9. Liability under the guarantee covers only defects resulting from causes inherent in the Equipment., In particular, the guarantee does not cover any damage resulting from improper or inconsistent use, storage, maintenance or transport of the Equipment, as well as colour differences between the parts exposed and not exposed to solar radiation, the influence of chemical or abrasive agents, atmospheric pollution or accidental punctures and abrasions, the presence of stains or rings from greasy or dying substances (fats, creams, lotions or oils), permanent staining with dyes such as inks, permanent markers or other non-permanent dyes used in the production of clothing (e.g. dyes used to make blue jeans).
10. The guarantee does not cover any mechanical damage to the Equipment.
11. The buyer loses the guarantee rights in the event of:
12. the Manufacturer states that the Equipment was repaired by entity other than the Authorized Service,
13. making any design modifications to the Equipment without the prior written consent of the Manufacturer,
14. using the Equipment contrary to its intended use,
15. using the Equipment after revealing any defect in it.
16. Regardless of the loss of the guarantee rights, described above, in point 6, the Manufacturer shall not be liable for any damage to property or caused to third parties, which may be caused by the use of the Equipment covered by the guarantee.
17. The guarantee does not exclude or limit the rights resulting from the warranty for defects. Exercising the rights under the guarantee does not affect the seller’s liability under the warranty for defects. If the Buyer exercises the rights under the guarantee, the time limit for the exercise of the rights under the warranty for defects is suspended on the date the Manufacturer is notified of the defect. The period runs further from the date of the Manufacturer’s refusal to perform the obligations arising from the guarantee or the ineffective expiry of the time for their performance.
18. The scope of the guarantee coverage is limited to the territory of the country in which the Equipment was sold.
19. The Manufacturer shall perform its obligations under the guarantee (removal of defects or damage to the structure of the Equipment arising from reasons inherent in the Equipment, and disclosed during the guarantee period) free of charge within 14 days from the date of delivery of the Equipment to the Manufacturer or the Authorized Service Centre. If the repair of the Equipment cannot be performed within the above-mentioned period, the Manufacturer shall inform the Buyer of the above, and also indicate the reasons for the delay and the expected date of fulfilment of the recognized guarantee request.
20. The use of the guarantee rights requires the total (cumulative) fulfilment of four conditions:
21. presenting a VAT invoice, receipt or other proof of purchase of the equipment to the Manufacturer, photographic documentation of the defective Equipment, together with a brief description of the reasons for submitting a guarantee claim,
22. reporting the defect within 14 (fourteen) days of its detection,
23. delivering the Equipment in original packaging at the expense of the Manufacturer, to the address indicated above in the guarantee card or to the address of the Authorized Service Centre,
24. designation of the place where the Manufacturer delivers the equipment after repairing it (limited to the country in which the Equipment was purchased).
25. The guarantee period is extended for the duration of the repair, starting from the date of delivery of the Equipment to the Manufacturer or to the Authorized Service Centre, to the date on which the Equipment was returned to the Buyer.
26. The responsibility of the Manufacturer or the Authorized Service Centre is to define the scope and the method of repairing the Equipment.
27. The guarantee is limited to the repair of the Equipment. The Manufacturer reserves the right to replace the Equipment with a non-defective one, if the repair exceeds the price of the Equipment indicated in the proof of purchase. Under the guarantee, the Buyer shall not be entitled to demand that the Equipment be replaced with a new one. The guarantee, in particular, does not cover liability for losses or damages incurred by the Buyer in connection with the fact that one is not able to use the Equipment.
28. The Manufacturer shall not be liable for any damage to the Equipment caused during the performance of the transport service by the delivery company until it is collected by the Manufacturer from the delivery company.
29. If the shipment of the Equipment was ordered by the Manufacturer, the Buyer is obliged to check the technical condition of the Equipment upon its receipt. If the Buyer finds that the Equipment has been damaged during the transport, the Buyer is obliged to:
30. immediately, not later than within 3 days from the date of receipt of the shipment, notify the Manufacturer of any damage to the Equipment that occurred during transport, in order to enable the Manufacturer to submit a complaint to the delivery company and pursue related claims,
31. provide the Producer with a complaint report drawn up between the Buyer and the delivery company.
32. The guarantee regulations contained in this document are the sole and exclusive guarantee rules for HABYS limited liability products.

Other language versions available here:

www.habys.com/warrantymanuals

Manufacturer
Shanghai Sintang Industrial Co., Ltd, Linsheng Road No. 136, Tinglin Town, Jinshan District, Shanghai, China Made in China
Authorized Representative HABYS Sp. z o.o. ul. Produkcyjna 16, 38-200 Jasło
tel.: +48 887 766 115, info@habys.pl www.habys.pl

References

• Stoły do masażu, stoły rehabilitacyjne, łóżka do masażu i rehabilitacji - Habys

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>