VOGUE APPLIANCES 330494 T-Canopy Rangehood Instruction Manual

330494 T-Canopy Rangehood
Instruction Manual

T-CANOPY RANGEHOOD 900mm
BLACK STAINLESS STEEL
To prevent the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time

Dear Customer,
If you follow the recommendations contained in this Instruction Manual, our appliance will give you constant high performance and will remain efficient for many years to come.

Product Specification & Technical Parameters

RECOMMENDATIONS AND SUGGESTIONS

INSTALLATION

• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
• Please read this instruction manual before installing and using this range hood. Please keep this instruction manual in a safe place for future reference.
• Only a qualified and trained service technician can undertake the work of installation and servicing.
• Check that the main voltage corresponds to the one indicated on the rating plate fixed inside the hood.
• If the hood is used in conjunction with non-electrical appliances (e. g. gas burning appliances), a sufficient degree of ventilation must be guaranteed in the room to prevent the backflow of exhaust gas. The kitchen must have an opening directly with the open air to guarantee the entry of clean air.
• The minimum distance is 750mm from the range hood to a gas hob and 650mm to an electric hob. If the installation instructions for gas hobs specify a greater distance,  this must be taken into account.

NOTICE: Two or more people are required to install or move this appliance.
Failure to do so can cause physical injuries.

USE

• The range hood has been designed only for domestic use to eliminate kitchen fumes.
• Never use the hood for purposes other than what it has been designed for.
• Never leave high naked flames under the hood when it is in operation.
• Adjust the flame intensity to direct it onto the bottom of the pan only; making sure that it does not engulf the pan sides.
• The deep fat fryer must be continuously monitored during use: overheated oil can burst into flame.
• The hood should not be used by children or persons not instructed in its correct use.

MAINTENANCE

• Proper maintenance of the range hood will assure proper performance of the unit.
• Disconnect the hood from the main supply before carrying out any maintenance work.
• Clean and/or replace aluminum grease filters and activated charcoal filters after a specified period of time.
• Clean the hood using a damp cloth and a neutral liquid detergent.
• DISPOSAL: Do not dispose of this product as unsorted municipal waste.
  Collection of such waste separately for special treatment is necessary.

WARNING!!
In certain circumstances, electrical appliances may be a dangerous hazard.

• Do not check the status of the filters while the cooker hood is operating

• Do not touch the light bulbs after appliance use

• Do not disconnect the appliance with wet hands.

• To reduce the risk of fire or electric shock, do not use this fan with any solid-state.

• Avoid free flame, as it would do damage to the filters from a fire hazard

• Constantly checking food frying to avoid that overheated oil may become a fire hazard

• Disconnect the electrical plug prior to any maintenance or servicing.

• Children don’t recognize the risks of electrical appliances. Therefore use or keep the appliance only under the supervision of adults and out of the reach of children.

• TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
  a) Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
  b) Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel-burning equipment to prevent back drafting.
  c) When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other hidden utilities.
  d) Ducted fans must always be vented to the outdoors.

  • Don’t use this product outdoors.

  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction, concerning the use of the appliance by a person responsible for their safety.
    Children should be supervised to ensure that they do not play with the appliance.

  • There shall be adequate ventilation in the room when the range hood is used at the same time as appliances burning gas or other fuels.

  • There is a fire risk if cleaning is not carried out in accordance with instructions.

• The exhaust air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.

CHARACTERISTICS

DIMENSIONS

INSTALLATION & USE

OPERATION OF CONTROLS

The hood is operated using the touch control on the front panel.
The light switch turns the lamps on and off.

POWER
When connected to the electricity, all the button lights are on for one second and then go off. Now the hood is in standby mode.
In standby mode, press the on/off button once, and the range hood motor work at low speed. The screen shows” 1”.
Press the button “+” the first time, the range hood motor turn to medium speed, and the screen shows “2”.
Press the button”+” the second time, the range hood motor turn to the high- speed setting, and the screen shows “3”.

TIME DELAY
When the motor is working, use the time delay to turn off the range hood at a specific time.
Long press the button “+” and “-“at the same time for two seconds, and the range hood will be turned off automatically in 5 minutes.

MEMORY FUNCTION
The range hood could keep the memory of the speed setting. For example, the default turn-on speed is a low-speed setting “1”, if the last operation of the speed setting turns to medium speed “2”. The range hood will work in medium speed “2” when turn on next time. This memory will be lost once disconnect from the electricity.

Grease Filters
The grease filters should be cleaned frequently. Use a warm detergent solution. Grease filters are washable.
See the “INSTALL FILTERS” section for removal and installation instructions.

Non-Ducted Recirculation charcoal filter
The non-ducted recirculation charcoal filter should be changed every 6 months.
See the “INSTALL FILTERS” section for removal and installation instructions.

INSTALL THE DUCTWORK (DUCTED HOODS ONLY)
Caution: To reduce the risk of fire, the use of metal ductwork is preferred.

1. Decide where the ductwork will run between the hood and the outside.

2. A straight, short duct run will allow the hood to perform most efficiently.

3. Long duct runs, elbows, and transitions will reduce the performance of the hood. Use as few of them as possible. Larger ducting may be required for best performance with longer duct runs.

4. The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels” “Regulations concerning the discharge of air have to be fulfilled.

5. Install wall cap. Connect round metal ductwork to the cap and work back towards the hood location. Use duct tape to seal the joints between ductwork sections.

INSTALL ELECTRICAL
Electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards. This range hood must be properly grounded.
Turn off electrical power at the service entrance before wiring.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.

INSTALL THE HOOD
Note 1: On stainless steel hoods, carefully remove the plastic protective film from all exterior surfaces of the hood and chimney prior to final installation.
Note 2: At least two people will be required to mount the hood.

INSTALL THE HOOD
The minimum hood distance above the cooktop must not be less than 650mm.
A maximum of 750mm above the cooker is highly recommended for the best capture of cooking impurities.
The distance over 750mm above the cooker is at the installer and user’s discretion – providing that ceiling height and flue length permit.

1. Secure the hood mounting bracket to the wall using (3) ST 5 x 45mm mounting screws and drywall anchors. Secure the chimney mounting bracket to the wall using (2) ST  4.2 x 30mm mounting screws and drywall anchors.

2. Fix the discharge collar into the air outlet adapter. Attach an adequate length of 150mm round duct to the air outlet adapter (If have one).
   

3. Align the hood body with the hood mounting bracket. Gently lower the hood until it securely engages the bracket.

4. Fix the decorative chimney bottom to the wall by using (2) 2.9*14.
   

5. Carefully slide the decorative chimney top down inside the decorative chimney bottom. Carefully place the decorative chimney bottom into the recessed area of the hood body top. Raise the decorative chimney top until its holes align with holes in the chimney mounting bracket (located on the wall). Level the hood and secure the chimney with 2 chimney bracket screws.

6. Double secure the range hood body with 2 screws from inside of the body.

INSTALL FILTERS

1. To remove the grease filter, push in on the metal latch tab. This will disengage the filter from the hood. Tilt the filter downward and remove it.

2. To install the grease filter, align the rear filter tabs with slots in the hood.
   Push in the metal latch tab, push the filter into position, and release.
   Make sure the filter is securely engaged after assembly.

3. Install the charcoal filter and fix the filter by using (2) M4*10.
   The charcoal filter is mainly for the recirculation model.

4. Install a grease filter after the charcoal filter is installed.

LED LAMP
This range hood may require one LED strip ( 12V, 6W Max)
WARNING: Always switch off the electrical supply before carrying out any operation on the appliance.
To change the LED strip:
Disassemble the metal light panel from the range hood. Loose the screw at the back of the light panel, and replace the LED strip with the same. Do not touch the replacement bulb with bare hands!

CAUTION:

1. THE SURFACE AND THE COVER OF THE LED LAMP MAY BE HOT. TAKE CARE WHEN TAKING THE REPLACEMENT.
2. BULBS MAY BE HOT. TAKE CARE WHEN TAKING THE REPLACEMENT.

CAUTION:
THE LIGHTS MAY BE HOT. TAKE CARE WHEN TAKING THE REPLACEMENT.

HOOD CLEANING
Stainless steel is one of the easiest parts to keep clean. Occasional care will help preserve its fine appearance.
Cleaning tips:

• Hot water with soap or detergent is all that is usually needed.
• Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth to avoid watermarks.
• For discolorations or deposits that persist, use a non-scratching household cleanser or stainless-steel polishing powder with a little water and a soft cloth.
• For stubborn cases use a plastic scouring pad or soft bristle brush together with cleanser and water. Rub lightly in direction of polishing lines or “grain” of the stainless finish. Avoid using too much pressure that may mar the surface.
• Do not allow deposits to remain for long periods of time.
• Do not use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface causing rust.
• Do not allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals that may be harmful. Rinse with water after exposure and wipe dry with a clean cloth.
• Painted surfaces should be cleaned with warm water and mild detergent only.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>