swim fun 1960 UFO Pool Robot User Manual

: June 11, 2024
: swim fun

Table of Contents

swim fun 1960 UFO Pool Robot
Important Precautions
Introduction
Specifications
Operation instruction
- Quick operation
- Cleaning the filter tray
Troubleshooting
Sound signal information
Winter storage
Packing list
Exploded view
Parts
Warranty
Customer service
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

swim fun 1960 UFO Pool Robot

Important: Never operate the cleaner when there are people in the pool.

Important Precautions

Please read this manual carefully, and use the cleaner according to the manual.
We are not held liable for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model applies to swimmingpools with a flat floor.
Please do not allow children to ride on it or play with it as a toy.
If the power line is damaged, it must be replaced by a certified professional.
Never power on the cleaner when it is out of the water.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
Store the pool robot in a cool, frost-free and ventilated location.
Keep out of direct sunlight
Frost will damage the battery.
The cleaner should be stored in a cool place when charging, and not covered with anything to prevent the damage of internal electrical components caused by overheating.
Only professionals can disassemble the sealed driving kit of the cleaner.
Do not operate while pool filter is running.
Please use the original and authorized power adapter only.
Do not use or store the cleaner near any heat source.

Important: The cleaner should be charged and discharged every three months if it needs to be stored for a long time to maintain battery life.

Introduction

The robotic pool cleaner UFO is a new type of rechargeable automatic cleaner that will ﬁlter the pool water and gets rid of suspended particles without replacing the pool water. It’s totally environmental-friendly.

Specifications

Art. no.	1960
Name	UFO Pool Robot
EAN	5704841019607
LED lights	2
Working voltage	12.6V
Power	30W
Working Cycle	Up to 90min
Rated input voltage of adapter	100Vac-240Vac
Input power of the adapter	47Hz-63Hz
Rated output current of adapter	1A
Rated output voltage of an adapter	12.6V
Charging time	5-6h
Battery capacity	5000mAh
Max. cleaning surface	50 m²
Tolerates saltwater	Yes
Filter capacity	appr. 42L/min
Filter capability	180 µm
Pool water temperature	10°-35°C
Moving speed	appr. 16m/min
IP Grade	IPX8
Charging environment temperature	0°-45°C
Max. Water depth	2m
Size LxWxH	330 x 330 x 180 mm
Weight	3.2kg

Storage condition
Always store your pool robot in a frost-free location
Short-term (less than 1 month)| -20°C-60°C, ≤75%RH
Medium-term (less than 3 months)| -20°C-45°C, ≤75%RH
Long-term (more than 3 months)| -20°C-20°C, ≤75%RH

Operation instruction

Precautions

Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Install the swing plate and floating handle before use.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
When fastening the top cover and chassis, please focus more on the installation direction as shown in the below figure: the arrow position near the buckle of top cover should be aligned with the hole position near the buckle of chassis.
When charging, it is strictly forbidden to face the bottom up to prevent the swing plate from being crushed.
Power off the cleaner after use.

Grab the floating handle and pull at the rope for lifting it on the water surface, and then grasp its handle to remove it from the pool. Hold the cleaner on the water surface for 10-15 seconds until it empties before removing from the pool.

Note: Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into the pool or lifting out of the pool.

Quick operation

Plug in the cleaner using the supplied adapter and charging line to charge the battery.

Note: When charging, it is strictly forbidden to leave the pool robot upside down to prevent the swing plate from being crushed.

Power off the cleaner before charging.
Clean the charging port before charging.
Red charging indicator indicates the battery is charging.
Green charging indicator indicates charging is finished. A full charge always takes 5-6 hours. The battery is not fully charged until after 5-6 hours even though the charging indicator turns green.

Press the switch to power on the cleaner. and lower the pool robot horizontally to the pool floor. The pool robot will start 20 seconds after you have switched on the power. The cleaner will stop running after completing the working cycle. The floating handle can be hooked by a hook with a telescope pole, and the cleaner is pulled to the edge of the pool.

Power-off operation

A sound signal comes when lifting the pool robot out of the pool. Press the switch to OFF and the cleaner will be shut down. Always clean the filter tray after use. Power-off operation: the buzzer will be alarming when lifting out of the pool. Press the switch to OFF and the cleaner will be sht down. Always clean the filter tray after use.

Functions and adjustment of wheels

swim -fun-1960-UFO-Pool-Robot-FIG-7

There are 4 wheels on the cleaner, of which the left and right wheels are fixed. The front and back wheels can be selectively adjusted according to different conditions so as to adjust the running path of the cleaner. swim
-fun-1960-UFO-Pool-Robot-FIG-8

Setting wheel angle and running path
A, B, C are printed on the groove of the wheel limit pile of the bottom. Wheel limit piles will be installed by default on C (left) and A (right).
As shown in the figure, push the wheel buckle, pull down the wheel components, and remove them. Then reinstall the limit pile into chassis to realize the different running paths
Three settings for wheels are recommended.

Setting 1

Default, setting: B-C, for most of pools

Wheel angle|
---|---
Running path|

Setting 2

C-A, when the turning angle is too large

Wheel angle
Running path

Setting 3

C-C, when the length and width of the swimming pool are large

Wheel angle|
---|---
Running path|

Setting 4

B-A, for round pools

Wheel angle|
---|---
Running path|

Note: These are the recommended settings. Different settings may work better for your pool.

Cleaning the filter tray

Open the cleaner by the clips.
Take off the filter tray
Clean the filter tray and chassis
Reassemble the cleaner
Clap on the clips

Troubleshooting

Symptom	Possible reason	Solution
Sound signal silent or impeller rotating after power on	Low battery	Recharge

the battery
Internal fault| Contact after-sales service
The sound signal still alarms or the impeller does not rotate after the cleaner is fully immersed in the water| ****

Internal fault

| ****

Contact after-sales service

The swing plate cannot stand when the cleaner touching the wall

| ****

The swing plate is stuck

| Remove the cleaner from the pool and try to manually rotate the swing plate or contact the after-sales service.
The swing plate can stand when the cleaner touching the wall, but the cleaner cannot reverse| ****

The water channel is stuck

| ****

Try to manually overcome stuck condition

Charger indicator does not work| The adapter is damaged| Contact after-sales service

The cleaner does not have a full coverage for the floor

| ****

Improper wheel angel

| Adjust wheel position (see

4.3 Functions and adjustment methods of wheels)

Special pool shape

| Adjust wheel position (see

4.3 Functions and adjustment methods of wheels)

Swimming pool water circulation system is on| Shut down the system

Sound signal information

State	Expression
Power on	Sound signal when not fully immersed in the water; Soud signal stops

after fully immersed in the water
Power off| Sound signal stops

Winter storage

During the winter season when the outside temperatures fall below 10°C UFO Pool Robot should be removed to prevent damage from freezing water. Store it inside in a dry and frost free location. Note that the battery must be charged every 3 months to avoid capacity reduction. Otherwise, the guarantee will be void.

Packing list

Item	Name	Model	QTY	Remark
1.	Cleaner body	1960	1	In carton
2.	Adapter		1	In carton
3.	User manual		1	In plastic bag
4.	Tow rope (with a floating ball)		1	In plastic bag
5.	Floating handle		1	In plastic bag
6.	Swing plate		1	In plastic bag
7.	Hook		1	Inside cleaner

Exploded view

No.	Art. no.	No.	Art. no.
1	10110	10	10121
2	10122	11
3	10111	12	10186
4		13	10114
5		14	10119
6	10116	15	10118
7		16	10115
8	10112	17	10120
9	10109	18	10117

Parts

swim -fun-1960-UFO-Pool-Robot-FIG-15

Warranty

The warranty period is according to the national laws regarding consumer purchase. The warranty period applies from the date of purchase on your purchase receipt. The receipt must be presented at service calls during the warranty period. It is therefore important that you save your sales receipt. The manufacturer guarantees safe operation and product liability based on the following specific conditions:

Installation and use in accordance with the manual’s instructions.
Use only original spare parts

The warranty does not cover normal wear and tear, scratches, abrasions or cosmetic damage. More specifically, the warranty does not cover damage caused if:

Improper use or handling, including frost damages
Fall or shock
Repairs, alterations or etc. performed by anyone other than Swim & Fun
Improper storing in extremely high or low temperatures, including frost

In the event of guarantee claims please contact your dealer. When returning a defective product, it must be packed in such a way that it is not damaged during transport. It is your responsibility that the product arrives safely. You must state your name, address, phone number and preferably your e-mail address. If the product are to be returned to you! Always remember to state what is wrong with your product.