K RCHER WR 10 High Pressure Cleaners User Manual

June 9, 2024
K RCHER

K RCHER WR 10 High Pressure Cleaners

Please read and comply with these original instructions prior to the initial operation of your appliance and store them for later use or subsequent owners.

Danger or hazard levels

DANGER
Pointer to immediate danger, which leads to severe injuries or death.
WARNING
Pointer to a possibly dangerous situation, which can lead to severe injuries or death.
CAUTION
Pointer to a possibly dangerous situation, which can lead to minor injuries.
ATTENTION
Pointer to a possibly dangerous situation, which can lead to property damage

Safety instructions

DANGER
Risk of injury! The appliance may not be modified.
DANGER
High-pressure jets can be dangerous if improperly used. The jet must not be directed at persons, animals, live electrical equipment or at the high pressure cleaner itself.
WARNING
Danger of burns from hot surfaces and risk of scolding.
Please wear safety gloves and -goggles when working with the appliance. Please observe the safety instructions of your high pressure cleaner

Environmental protection

The packaging material can be recycled. Please do not place the packaging into the ordinary refuse for disposal, but arrange for the proper recycling.
Old appliances contain valuable materials that can be recycled. Please arrange for the proper recycling of old appliances. Please dispose your old appliances using appropriate collection systems.
Notes about the ingredients (REACH)
You will find current information about the ingredients at: www.kaercher.com/REACH

Use as intended

The appliance is suitable for performing weed control when used in combination with a high pressure cleaner.
Using the nozzles on the spray bars , uncompressed hot water (max. 100°C) is applied to the plants. Any other use is prohibited.

Device elements

  1. Spray lance
  2. Power nozzle
  3. Screw connections
  4. Temperature indicator
  5. Spray head

Flow restrictor

In order to maintain a consistently high temperature (above 90°C) of the water, a power nozzle must be inserted into the screw connection of the spray head to restrict the flow.

Note
The necessary power nozzle is matched to the corresponding high-pressure cleaner and must be ordered separately

Hot water high-pres- sure cleaner| Order

number Power nozzle

---|---
HDS 6/14 C| 2.113-070.0
HDS 6/14-4 C| 2.113-070.0
HDS 7/12-4 M| 2.113-006.0
HDS 7/16 C| 2.113-041.0
HDS 8/17 C| 2.113-071.0
HDS 8/18-4 C| 2.113-071.0
HDS 8/18-4 M| 2.113-071.0
HDS 9/18-4 M| 2.113-005.0
HDS 10/20-4 M| 2.113-021.0
HDS 12/18-4 S| 2.113-010.0
HDS 13/20-4 S| 2.113-025.0
HDS 1000 De| 2.113-071.0
HDS 1000 Be| 2.113-071.0
HDS 13/20 DeTr.1| 2.113-026.0
HDS 17/20 DeTr.1| 2.113-026.0

Note: Power nozzles for hot water high pressure cleaners not listed here must be requested from the service partner.

Spray head

Installing the spray head

Installing the spray head

➡ Push power nozzle into the screw connection.
➡ Screw the spray head onto the spray lance.

Operation

WARNING
Risk of burns! Do not direct the stream of water at people or animals.
During operation, do not touch WR 10 or reach into the stream of water.
➡  Set the device switch on the high-pressure cleaner to max. 98 °C.
➡  If installed, set the Servo Control to the  max. setting

Note
Depending on the high-pressure cleaner in use, the heating-up time can last between 2 and 5 minutes.

Temperature display

The temperature indicator provides information on when the required water temperature has been reached.
Temperature display

➡ Switch on the high pressure cleaner and pull the lever of the high pressure gun.
➡ Wait until hot water emerges from the spray bar.
➡ The temperature indicator changes with the increasing water temperature.
The colour of the indicator fields changes from left to right from black to brown.
➡ When the bar is coloured completely green at the right, the device is ready for operation.

Weed removal

Weed removal

➡  Guide the spray head slowly over the weeds.
➡  Repeat the procedure several times if required.

Note
The optimal effect has been achieved when the hot water flows with almost no pressure and a light steam formation

Shutting down

WARNING
Risk of burns! Let the WR 10 cool down before removal.

➡ After operation, spray cold water through the spray head for 2 minutes to allow it cool down.
➡ If necessary, rinse the spray head with clear water.

Care

➡ Check the spray head regularly for blockage of the nozzles.

Transport

Mind the weight of the appliance during transport

Storage

  • Consider the weight of the appliance when storing it.
  • Store the appliance in a frost free area

Steam escaping from the spray head:
➡ Reduce the temperature setting on the high-pressure cleaner.
The emerging water pressure is too high:
➡ Mount power nozzle in screw connection.
➡ Select a suitable power nozzle (see table). High-pressure cleaner switches off/the high-pressure cleaner burner does not start:
➡ Check the nozzles on the spray head for contamination.
➡ Check the spray head for calcification.

Accessories and Spare Parts

Only use original accessories and spare parts, they ensure the safe and trouble-free operation of the device.
For information about accessories and spare parts, please visit www.kaercher.com.

Technical specifications

| WR 10
---|---
Working width| 100 mm
Target input temperature min.| 90°C
Target input temperature max.| 100°C
Weight (kg)| 0.3

Register your product and benefit from many advantages.

www.kaercher.com/welcome

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals