Shuttle NC40U Series Mini PC User Guide

June 9, 2024
Shuttle

Shuttle NC40U Series Mini PC User Guide
Shuttle NC40U Series Mini PC

Product Overview

Product Overview

  1. USB 3.2 Gen1 Type-A ports
  2. USB 3.2 Gen1 Type-C Port (w/DP)
  3. MIC-in
  4. Headphones
  5. Hard disk drive LED
  6. Power switch / Power LED
  7. Perforation for optional WLAN
  8. Ventilation Hole
  9. Kensington® Lock Hole
  10. Power Jack (DC IN)
  11. DisplayPort
  12. HDMI 2.0 Port
  13. USB 3.2 Gen2 Type-A ports
  14. LAN Port

Hardware Installation

A. Begin Installation

For safety reasons, please ensure that the power cord is disconnected before opening the case

  1. Unscrew two screws of the back cover and remove it.

B. Component Installation

  1. Place an HDD or SSD in the rack and secure with the four screws from the sides.
    Component Installation 

  2. Put the rack back into the back cover and refasten the screw. Connect the Serial ATA and power cable to the HDD or SSD.
    Component Installation 
    This model supports 2.5” SATA HDDs and SSDs up to a thickness of 15mm.

  3. Locate the M.2 key slots on the motherboard. Install the M.2 device into the M.2 slot and secure with the screw.
    Pasting the supplied thermal pad on the M.2 SSD can effectively reduce its temperature.

    • M.2 2230 E Key slot
      Component Installation 

    • M.2 2280 M key slot
      Component Installation 

  4. Replace the back cover. Turn your NC40U upside down and remove the other cover.

  5. Please install device into the M.2 slot on top side by steps B3. if you need.
    Component Installation 

  6. Locate the SO-DIMM slots on the motherboard.
    This motherboard does only support 1.2 V DDR4 SO-DIMM memory modules.

  7. Align the notch of the memory module with the one of the relevant memory slot.
    Component Installation 

  8. Gently insert the module into the slot in a 45-degree angle.

  9. Carefully push down the memory module until it snaps into the locking mechanism.
    Component Installation 

  10. Repeat the above steps to install an additional memory module, if required.

C. Connecting to Power

  1. Please replace and affix the case cover with two screws, then connect the power cord.
    Connecting to Power 

  2. Complete.
    Connecting to Power 
    Please press the “Del” key while booting to enter BIOS. Here, please load the optimised BIOS settings.

Using the Vertical Stand (optional)

Install the vertical stand and check if it is properly aligned, then tighten securely with four screws.
Using the Vertical Stand \(optional\)

Installation of VESA Mount (optional)

  • Follow the steps 1-3 to install the VESA mount
    Installation of VESA Mount \(optional\)
    Supports 75x75mm and 100x100mm VESA standard

Safety Information

Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Dispose of used batteries according to the  manufacturer’s instructions.

All bundled parts, power cord included, shall not be used without this product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

This device meets the requirements for the EU conformity in accordance to the currently valid EU directives.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals