V-TAC VT-5155 WiFi Ambiance Lamp Instruction Manual
- June 9, 2024
- V TAC
Table of Contents
VT-5155 WiFi Ambiance Lamp
Instruction Manual
WEEE Number: 80133970
INSTALLATION INSTRUCTION WIFI AMBIANCE LAMP
TECHNICAL DATA
| MODEL | VT-5155 |
|---|---|
| WATTS | 5W |
| VOLTAGE | AC220-240V,50/60Hz |
| LUMEN | 550LM |
| BEAM ANGLE | SPHERE 360° |
| DIMENSION | 198x200x110mm |
| BODY TYPE | PLASTIC |
| USB TYPE | TYPE-C |
INTRODUCTION & WARRANTY
Thank you for selecting and buying V-TAC SMART LED Lighting. V-TAC will serve
you the best. Please read these instructions carefully before starting the
installation and keep this manual handy for future reference. If you have any
other query, please contact our dealer or local vendor from whom you have
purchased the product. Th Usage of product for 24 Hours a day would void the
warranty. This product is warranted for manufacturing defects only.
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT:
SUPPORT6V-TAC.EU FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR
DISTRIBUTOR OR NEAREST DEALERS. V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000,
BUL.L.KARAVELOW 98
SAFETY WARNING
- Lamps are limited to indoor use and are not advisable for use in humid environment
- Lamp is to be used in well ventilated areas and normal installation.
- Caution: This lamp is NOT to be used in a totally enclosed fixture which is not good for heat emission. Please do not install the lamp in enclosed space as it will shield the wifi signal due to which resulting in the poor functioning of the product.
- Lamps and lanterns cannot be installed on the surface of ordinary combustible materials. Increase in temperature is normal for lamps.
- Do not exert external force or throw on the lamp.
- Lamps should be stored in cool/dry place. Always make sure the environment is clean before installing the lamp.
- Do not discard the lamps with regular trash. Lamps are made with electronic components and should be properly disposed at designated locations with unified treatment like traditional electronic equipment.
NOTE:
- This device requires Wi-Fi Frequency 2.4Ghz
- Indoor use only
- Operating frequency (maximum transmitted power) 2400MHz -2483.5MHz (ZOdBm)
This marking indicates that this product should not be disposed of with
other household wastes.
MULTI-LANGUAGE MANUAL QR CODE
http://vtac.store/vt5155
Please scan the QR code to access the manual in multiple languages.
INSTALLATION
Step 1: Connect the wire Type-C to the device.
Step 2: Turn the power ON to test the device.
Step 3: Enable WI-Fl and bluetooth on your phone device.
Step 4: Scan the given QR code, or download “V-TAC Smart Light” from the
App Store (i0S) or the Google Play Store (Android).
https://itunes.apple.com/cn/app/v-tac-smart-
light/id1406697927?l=en&mt=8
https://play.google.com/store/apps/details?id=com.vtac.smartlight
Step 5: Open the V-TAC Smart Light app and tap on register for creating a
new account.
Step
6:
A) Mobile Number: Select the country, then enter your mobile number. Once
done, tap ‘Next’.
B) E-Mail: Enter your email id and tap on ‘Next’.
Step
7: Enter the verification code which will be sent to your mobile
number/email id, then assign a new password to your account and tap on
“Confirm”.
Step
8: Tap on ‘Add Device’ or the + sign. Make sure the lamp is switched on.
Step 9:
Choose ‘Lighting’ to start pairing the lamp to the app.
Step
10: V-TAC Smart Light Device offers two types of pairing modes:
- EZ Mode – Light flashes rapidly
- AP mode – Slow Flash or long brightness
How to enable/reset the smart device into pairing mode -Long press the reset key till blue led light flashes rapidly, then it will be ready for configuration.
Step
11: Once you have successfully completed step 10, you will be redirected to
below page, where the App searches, registers and initializes the device(lamp)
(ref image below).
Step
12: Once your device is successfully added, rename the device to your
preference.
Step
13: After successfully pairing the lamp with the app, you can start
controlling multiple features of the lamp through your mobile— on/off switch,
changing the colour temperature, timing & schedules, dimming options, and
more. 
ALEXA SETTINGS
Step 1:Install the Amazon Alexa app via the App Store(iOS) or the Play Store
(Android) and register. If you already have an existing account with Amazon
Alexa, please proceed to logging in.
Step
2: Once you are on the Amazon Alexa home page, tap on the lower right icon —
where the arrow is pointed— to add a new device and skill.
Step
3: Tap on settings and tap on skills and games” as shown below.
Step
4: Search for ‘V-TAC Smart Light’ on the “Skills & Games” page as shown
below.
Step 5: Enable the Skill.
Step
6: Enter your V-TAC Smart Light login ID and password and tap on “Link Now”
Step
7: Once you tap on Link Now, you will be redirected to a new page requesting
for authorization(Ref Image below). Tap on “Authorize”
Step
8: You will receive confirmation of the account being linked successfully (Ref
Image below)
Step
9: Discover your smart device on Alexa. Once you have enabled the skill
A) You can use voice command “Alexa discover devices” to the Alexa device
which you have.
B) To add device manually on and tap on Add device, select the device home
page tap on which you are adding and tap on discover device.
Note:
Discovering the device must be done every time the device’s name is changed on
the app.
ALEXA Commands
Now, you can control your smart device using voice commands on Alexa.
Below are a few commands you can use:
- Alen, turn on/off bedroom light.
- Alexa, set bedroom light to 50 percent.
- Alexa, set bedroom light to green.
- Alexa, set bedroom light to warm white
THINGS TO REMEMBER BEFORE STARTING INSTALLATION :
- V-TAC Smart Light App & Amazon Alexa App
- Make sure you have Amazon Alexa Device(including Echo, Echo Tap, or Echo Dot)
- Smart Device – Lamp
- Stable WO network
GOOGLE HOME SETTINGS)
Step 1: a&b) Install the Google Home app via the App Store (iOS) or the Play
Store (Android) and register. If you already have an existing account with
Google Home, please proceed to logging in.
c) Create a New Home/Choose from the existing home if any.
d) Power ON the Google Home device and connect it to the App.(Then Proceed to
step 2)
Step
2: Once you are on the Google home page, tap on the Add “+” icon— to add a new
device and skill. And then tap on Set up device as shown in below image.
Step
3: Make sure the Smart Bulb is paired with V-TAC Smart Light app before
starting step 3. Tap on the arrow section as highlighted in the below image.
Step
4: Type “V-TAC Smart Light” on the search bar and tap on the icon of “V-TAC
Smart Light”
Step
5: Sign In with your V-TAC Smart Light Login credentials to Link the Smart
Light device
Step
6: Tap on Authorize in order to proceed to linking the device.
Step 7
a. Account will now be linked, please stay on the page you will be redirected
in few seconds to select the device to add to your home.
b. Select the device and tap on Next as show in image b.
Step
8: Select the Home where you would like to add the Smart Light under. (Or) you
can create a New home in order to add the Smart Light to it.
Step
9: You have succesfully added Smart Light device to your Google home App.
Step
10:
a. You can turn the Lamp On/OFF by taping on On/Off options as shown below.
(OR) You can tap on the Smart Lamp.
b. You will be redirected to page(as shown in image b) where you can control
the lights “Power and Dimming functionality”.
Google Commands:
Now, you can control your smart device using voice commands on Google Home.
Below are a few commands you can use:
- Ok, Google, turn on/off bedroom light
- Ok, Google, set bedroom light to 50 percent.
- Ok, Google, set bedroom light to green.
- Ok, Google, set bedroom light to warm white.
THINGS TO REMEMBER BEFORE STARTING INSTALLATION:
- V-TAC Smart Light App & Google Home App
- Make sure you have Google Home Device
- Smart Device – Lamp
- Stable Will network
STEPS TO DISSASSEMBLE THE LAMP (ONLY FOR MARKET SURVEILLANCE AUTHORITY)
DISASSEMBLING DIAGRAM
HOW TO DISASSEMBLE THE DEVICE
- Power off and take out the Lamp
- Pry off the lamp cover with a straight line (it needs a lot of force to glue the lamp cover)
- Unscrew 3 lens screws with a cross jack and take out the lens
- Carry out photoelectric parameter test in this state
Note: Dissassembling the Lamp will Void the Warranty
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>