KARCHER BD 17-5 C Floor Scrubber User Manual

June 9, 2024
Karcher

KARCHER BD 17-5 C Floor Scrubber User Manual
KARCHER BD 17-5 C Floor Scrubber

General notes

Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Proceed accordingly. Keep both books for future reference or for future owners.

Intended use

Use the device only in accordance with the information in these operating instructions.

  • This device is suitable for commercial use, e.g. in hotels, schools, hospitals, factories, shops, offices, and rental companies.
  • The device is suitable for cleaning hard surfaces and carpets.
  • The device is not suitable for polishing vehicles.
  • Only equip the device with original accessories and spare parts.
  • Never use the device in potentially explosive atmospheres.

Safety instructions

Before using the device for the first time, read and observe these operating instructions and the accompanying brochure: Safety information for single disc machines, No. 5.956-251.0.

Environmental protection

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations

Electrical and electronic appliances contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential threat to human health and the environment. However, these components are required for the correct operation of the appliance. Appliances marked by this symbol are not allowed to be disposed of together with the household rubbish.
Notes on the content materials (REACH) Current information on content materi can be found at: www.kaercher.com/ REACH

Accessories and spare parts

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.
Information on accessories and spare parts can be found at www.kaercher.com.

Accessories

Description Order no.
Disc brush, red, 160 mm (medium, standard) 6.994-112.0
Grit brush, green, 160 mm 6.994-113.0
Polishing brush, natural hair, 160_mm 6.994-114.0
Carpet brush, blue, 160 mm 6.994-115.0
Disc brush, red, 200 mm (medium, standard) 6.994-116.0
Grit brush, black, 200 mm 6.994-117.0
Polishing brush, natural hair, 200_mm 6.994-118.0
Pad drive plate 6.994-119.0
Pad, white 6.994-120.0
Pad, black 6.994-121.0
Pad, red 6.994-122.0
Pad, green 6.994-123.0
Pad, beige 6.994-124.0
Pad, crystallisation 6.994-125.0
Pad, polishing wool 6.994-126.0
Pad, microfibre 6.905-189.0
Pad, set 2x D 170 melamine 6.371-354.0
Angle brush, red (standard) 6.994-127.0
Grit angle brush, green 6.994-128.0
Splash guard 6.994-129.0
Detergent tank, 3.5 litres 2.644-023.0
Power cord, EU 6.648-767.0

Detergent

Usage Detergent
Maintenance cleaning of tiles in sanitary areas RM 751
Maintenance cleaning and basic cleaning of industrial floors RM 69 ASF
Coating removal on all alka- line-resistant floors (e.g.PVC) RM 752
Coating removal on linole- um floors RM 754
Intermediate cleaning of carpets RM 768 iCap- sol
Crystallisation agent for floors containing calcium RM 749

Scope of delivery

Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer

Control elements

Illustration A
Control elements

  1. Screw, washer (brush attachment)
  2. Brush
  3. Handle, adjustable
  4. Handle
  5. Brush speed rotary knob
  6. Power switch
  7. Allen key
  8. Mains connection cable with mains plug
  9. Cable clip
  10. Type plate

Initial startup

Attaching the brush/pad drive plate

ATTENTION
Risk of damage
The fastening screw protruding over the brush body can cause scratches on the cleaning object if the brush is too heavily worn
Replace the cleaning brush in good time before the bristles are too short

  1. Select the brush suitable for the cleaning task or the pad drive plate.

  2. Make sure that the mains plug is unplugged.

  3. Unscrew the screw for brush attachment. Use the Allen key provided for this.
    Illustration B
    Initial startup

  4. Driver

  5. Disc brush/pad

  6. Washer

  7. Screw

  8. Place the brush or pad drive board on the driver.

  9. Screw in and tighten the screw and washer.

  10. Centre and press the pad onto the pad drive plate

Adjusting the handle

  1. Loosen the adjustable handle by turning it anticlockwise
    Illustration C
    Adjusting the handle 

  2. Handle

  3. Swivel the handle into the desired position.

  4. Tighten the handle by turning it clockwise.

Operation

Power connection

The voltage specified on the type plate must match the voltage of the power source.
Use only extension cables with splash guards.
The mains plug/extension cable connection must not be immersed in water

  1. Unwind the extension cable completely from the device.
  2. Set the power switch to “0”.
  3. Plug the mains plug into the socket

Adjust the speed

Recommended speed:

Application Speed in rpm
Basic cleaning 350…450
Removing coatings 350…450
Using cleaners 450
Crystallisation 450
Shampooing carpet 350
  1. Turn the brush speed rotary knob to the desired value.

Cleaning

DANGER
Danger of electric shock
The user can receive an electric shock from a damaged cable.
Never wrap the power cord around your body or neck.
Make sure that the power cord nevercomes into contact with the rotating brush or pad.

ATTENTION
Risk of damage
Working on the same area for too long can damage the floor covering.
Do not operate the device continuously on the same point.
Do not let the device run dry on sensitive floors

  1. Apply the detergent solution to the surface to be cleaned.

  2. Hold the device by the handle.

  3. Set the trigger to “I”.

  4. Hold the device with both hands and move the brush/pad over the surface to be cleaned.
    Note: Do not press the device onto the surface to be cleaned. The weight of the device is sufficient as contact pressure.

  5. Repeat the cleaning process if heavily soiled.

  6. Soak up the waste water with a wet vacuum cleaner or wipe it up with a cloth.

Shutting down

  1. Set the power switch to “0”.

  2. Pull the mains plug out of the socket.

  3. Clean the device with a moist cloth.

  4. Wind the mains cable around the device casing.
    Illustration D
    Shutting down

  5. Secure the end of the cable with the cable clip.

  6. Park the device in the parking position. This prevents the brush from becoming deformed.
    Illustration E
    Shutting down

Transport

CAUTION
Risk of injury, risk of damage
Be aware of the weight of the device duringtransportation.

  1. When transporting in vehicles, secure the device against slipping and tipping over according to the applicable guidelines.

Storage

CAUTION
Risk of injury and damage
Be aware of the weight of the device during storage.

Care and service

WARNING
Risk of injury
The device may start up unexpectedly. Be sure to pull the mains plug out of the socket before you start working on the device.

  1. Wash dirty pads at a maximum of 60 °C.
  2. Clean the casing of the device with a damp cloth and then rub dry.
  3. Check the mains cable for damage.

Troubleshooting guide

WARNING
Risk of injury
The device may start up unexpectedly.

Be sure to pull the mains plug out of the socket before you start working on the device.
In the event of malfunctions that cannot be remedied using the following information, please contact customer service

Unsatisfactory cleaning results

  • Replace the soiled pad and wash at a maximum of 60 °C.
  • Replace a worn brush/pad.
  • heck the suitability of the detergent used for the application.
  • Check the suitability of the brush/pad used for the application.

The device vibrates strongly

  • Check for central positioning of the pad on the pad drive board.
  • Check the attachment of the brush/pad.

The pad does not rotate

  • Check if foreign objects are blocking the pad drive board. Remove any foreign objects if necessary.
  • Plug the mains plug into the socket.

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site. (See overleaf for the address)

Technical data

BD 17/ 5 C

Device performance data
Voltage| V| 220-
| | 240
Phase| ~| 1
Frequency| Hz| 50-60
Power rating| W| 150
Degree of protection| | IPX4
Pad
Pad diameter| mm| 160/
| | 200
Pad speed| 1/min| 0…450
Ambient conditions
Permissible temperature| °C| +5…+4
range| | 0
Dimensions and weights
Length| mm| 330
Width| mm| 140
Height| mm| 300
Weight without accessories| kg| 5,4
Determined values in acc. with EN 60335-2-72
Overall vibration value| m/s2| <2,5
Uncertainty K| dB(A| 0,2
Sound pressure level Lp| dB(A| 68,6
Uncertainty KpA| dB(A| 1
Sound power level LWA + K uncertaintyWA| dB(A| 77,2
Subject to technical modifications.

Declaration of Conformity

EU Declaration of Conformity

We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.
Product: Floor cleaner
Type: 1.737-xxx

Currently applicable EU Directives
2006/42/EC (+2009/127/EC)
2014/30/EU
2011/65/EU

Harmonised standards used
EN 60335-1
EN 60335-2-72
EN 62233: 2008
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 1997+A1: 2001+A2: 2008
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN IEC 63000: 2018

National standards used

The signatories act on behalf of and with the authority of the company management.

Signature
Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 – 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2022/09/01

Declaration of Conformity (UK)

We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.
Product: Floor cleaner
Type: 1.737-xxx

Currently applicable UK Regulations
S.I. 2008/1597 (as amended)
S.I. 2016/1091 (as amended)
S.I. 2012/3032 (as amended)

Designated standards used
EN 60335-1
EN 60335-2-72
EN 62233: 2008
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 1997+A1: 2001+A2: 2008
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN IEC 63000: 2018

National standards used
The signatories act on behalf of and with
the authority of the company management.

Signature
Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 – 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2022/09/01

THANK YOU!
MERCI! DANKE! ¡GRACIAS!

Registrieren Sie Ihr Produkt und profitieren Sie von vielen Vorteilen.
Register your product and benefit from many advantages.
Enregistrez votre produit et bénéficier de nombreux avantages.
Registre su producto y aproveche de muchas ventajas.

www.kaercher.com/welcome

Bewerten Sie Ihr Produkt und sagen Sie uns Ihre Meinung.
Rate your product and tell us your opinion.
Évaluer votre produit et dites-nous votre opinion.
Reseñe su producto y díganos su opinión.

Qr code
www.kaercher.com/dealersearch

Symbols Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40
71364 Winnenden (Germany)

Karcher logo

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals