SUNCO LIGHTING T8 LED Tube Ballast Pass Installation Guide

SUNCO LIGHTING T8 LED Tube Ballast Pass

The Brighter Choice – T8 LED Tube Ballast Pass (Type B)

The T8 LED Tube Ballast Pass is an energy-efficient lighting solution designed to replace traditional fluorescent tubes in commercial and residential settings. The T8 LED Tube Ballast Pass is a Type B product, which means it is designed to work with  existing ballasts. The product comes with an install guide and manual that provides detailed instructions on how to install and use the product.

Specifications

• Voltage: 120/277V
• Wattage: 15W/18W
• Current: 0.14/0.06A, 0.165/0.075A
• Power Factor: 0.968
• Lumens: 1800/2200
• Color Temperature: 4000K, 5000K, 6000K
• Color Rendering Index (CRI): 80
• Beam Angle: N/A
• Fixture Color/Finish: Clear

Easy Installation Instructions

1. Turn off the power through the main circuit breaker. Flipping the light switch to the off position does not necessarily end the flow of electricity.
2. Remove existing bulb(s) from fixtures.
3. Please note that with Single Ended Power (SEP) tubes, the pins on the non-energized or dead end of tube are only used to hold that end of the tube in the socket. You will need non-shunted tombstones.
4. Make sure the wires going to the G13 socket are in the live end of the tube.
5. Locate your ballast, in many T8 fixtures, the ballast is covered by a casing.
6. Disconnect all of the wiring from both sides of the ballast, remove the ballast.
7. Cut the socket lead wires 1, 2, 3, 4, and 5. You will only need one set of sockets for single-ended tubes.
8. Strip one inch of the colored insulation off the remaining wires.
9. Connect the live and neutral wires (black and white) from the power source to the corresponding socket (blue and red) wiring using push-in connectors or wire nuts that screw on.

Warnings

• Do not operate the product in an environment with high humidity or moisture.
• Do not touch the product with wet hands or while standing on a wet surface.
• Do not install the product in an enclosed space or cover it with insulation.
• Do not use the product with a dimmer switch or in a dimming application.

T8 LED TUBE Ballast pass (type B)
Install Guide and Manual

EASY INSTALLATION

1. Turn off the power through the main circuit breaker. Flipping the light switch to the “off” position does not necessarily end the flow of electricity.
2. Remove existing bulb(s) from fixtures.
3. Please note that with Single Ended Power (SEP) tubes, the pins on the non-energized or “dead” end of tube are only used to hold that end of the tube in the socket. You will need non-shunted tombstones.
4. Make sure the wires going to the G13 socket are in the “live” end of the tube.
5. Locate your ballast, in many T8 fixtures, the ballast is covered by a casing.
6. Disconnect all of the wiring from both sides of the ballast, remove the ballast.
7. Cut the socket lead wires 1, 2, 3, 4, and 5. You will only need one set of sockets for single-ended tubes.
8. Strip one inch of the colored insulation off the remaining wires.
9. Connect the live and neutral wires (black and white) from the power source to the corresponding socket (blue and red) wiring using push-in connectors or wire nuts that screw on.

PRODUCT SPECIFICATIONS

WARNINGS
To reduce the risk of fire, electric shock or injury to people:

• Rewiring fluorescent fixtures for use with LED should only be performed by individuals who have been properly trained to perform basic electrical maintenance and repair.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• Check for damage during shipping prior to install. If the product is damaged, do not use it.
• Turn off the switch and circuit breaker before installing this LED light fixture.
• Tubes are not compatible with photo controls, occupancy sensors, or timing devices.
  Please review instructions carefully before proceeding.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>