FLUANCE Ai41 Powered Bookshelf Speaker User Manual
- June 9, 2024
- FLUANCE
Table of Contents
- Introduction
- What’s Included
- Front & Back Panel Layout
- Remote Control Layout
- Product Setup
- Turning On/Off Unit
- RCA Input
- Bluetooth® Pairing
- Optical Input
- Subwoofer Output
- Frequently Asked Questions
- Troubleshooting
- Specifications
- Certification Information
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Ai41 Powered Bookshelf Speaker
User Manual
Serious Performance™
Fluance.com
Introduction
Thank you for your purchase of your Fluance product. We hope you enjoy your
experience. If you have any questions please visit us at:
Fluance.com/support
Fluance believes everyone should experience audio in its truest form,
recreating the performance the way the artist intended. Utilizing only
superior components and expert audio engineering, their products are a
testament to the performance that can be achieved when a passion for music
takes center stage. The perfect complement to any audiophile’s lifestyle,
you’ll be enjoying live performances in your home for years to come.
Break-in Period
Our speakers have a Butyl rubber ring surrounding the cone. The break-in
period allows the rubber to loosen and stretch, allowing the cone a larger
range of movement, resulting in better sound reproduction. We recommend 10-12
hours of play at moderate volume to achieve this.
Online Resources
For videos on the full setup and configuration of your speakers visit us at:
Fluance.com/resources
What’s Included
Front & Back Panel Layout
Active Speaker – Front
-
Control Knob
• Volume
• Input Selection
• Power ON/OFF -
Source LED
• Blue (Solid) – Bluetooth Paired
• Blue (Flashing) – Bluetooth® Pairing
• Green (Solid) – RCA
• White (Solid) – Optical
• Red (Solid) – Standby Mode
• Red (Flashing) – Mute
• Red (Flash x2) – Volume Set to Max
• Red (Flash x2) – Bass/Treb Set to -5 or +5
• Blue/Green/White (Flash x2) – Bass/Treb Set to ® -
IR Sensor
Active Speaker – Back -
Bluetooth® Reset Pairing
-
Optical Input
-
RCA Input
-
Subwoofer Output
-
Left Speaker Output
-
DC Input
-
Power Switch
Passive Speaker – Back -
Speaker Input
Remote Control Layout
- Power ON/OFF
- Volume UP/DOWN
- Source
- Treble UP/DOWN
- Mute
- Play/Pause & Bluetooth Pairing Reset
To enable Bluetooth Pairing Reset, press + hold for 3 seconds. - Forward/Back
- LED Brightness – (100% > 25% > OFF)
- Bass UP/DOWN
Product Setup
-
Position the speakers with the Active Speaker on the right and the Passive Speaker on the left.
NOTE: If placing the speakers in a cabinet or on a shelf, position the front of
the speakers as close as possible to the front edge of the shelf for optimum
audio performance. -
Connect one end of the speaker wire to the binding posts on the back of the Active Speaker and connect the other end of speaker wire to the binding posts on the back of the Passive Speaker.
IMPORTANT: Ensure the same color wire is connected to the same color binding posts on each speaker.
NOTE: The included speaker wire is 8ft. If placing your speakers further than 8ft apart it is recommended to use standard 18 gauge speaker wire to connect the speakers over the longer distance. -
Connect the power adapter to the back of the Active Speaker and set the power switch to the ON position.
Turning On/Off Unit
Press the Control Knob to turn on the unit. Hold to turn off the unit.| Press
on the Remote to turn the unit on/off.
---|---
Source Selection
Press the Control Knob to cycle through the audio inputs.| Press on the remote
to cycle through the audio inputs.
---|---
The Source LED will show the below color for each source:
(Blue) Bluetooth
(Green) RCA
(White) Optical
RCA Input
-
Connect the RCA cable to your source device (Turntable, Smartphone, Computer…).
-
Connect the other end of the RCA cable to back of the Active Speaker.
-
Press the Control Knob to select the RCA input (Green LED).
-
Adjust volume on Ai41 as well as source device.
NOTE: When connecting a turntable to the Ai41, a phono preamplifier
(preamp) must be used. Some turntables include a built-in preamp but others,
without one, would require an external preamp.
Visit Fluance.com for more information on our phono preamplifier, the PA10.
Bluetooth® Pairing
-
Press the Control Knob to select the Bluetooth input (Blue LED).
-
Pair to “Fluance Ai41” on your source device.
-
Use the Remote to control playback on your source device.
NOTE: Adjust Volume on the source device as well as the Ai41.
NOTE: How you access your device’s Bluetooth settings may vary from one manufacturer to another. Maximum line of sight for Bluetooth range is 33ft. Obstacles may decrease transmission distance. -
If your device cannot find “Fluance Ai41”, you can reset Bluetooth pairing:
• Press and hold for 3 seconds to reset Bluetooth pairing.
OR
• Press the Bluetooth Pairing Reset Button on the back of the unit.
Optical Input
-
Connect the Optical cable to your source device (TV, Computer, Game Console…). Ensure protective caps are removed from the ends of the Optical cable.
-
Connect the other end of the Optical cable to the back of the Active Speaker.
-
Press the Control Knob to select the Optical Input (White LED).
-
Adjust the volume on Ai41 as well as source device.
Optical Audio Signal Compatibility
The Ai41 does not support Dolby Digital Audio or DTS Audio. Locate the audio
output settings on your source device and ensure Dolby Digital is turned off.
The correct audio output setting is commonly referred to as PCM or Stereo.
Some TVs also require that audio output be enabled. This setting may be
referred to as External Speakers. Ensure this is selected as your
speaker/audio output.
For instructions on a specific device, please consult the device’s user
manual.
Subwoofer Output
IMPORTANT: When a subwoofer cable is connected, the Ai41 will automatically cut frequencies below 80Hz to optimize performance. The subwoofer cable must be removed to resume full frequency playback.
- Connect the Subwoofer cable to your powered subwoofer.
- Connect the other end of the Subwoofer cable to the back of the Active Speaker.
- Adjust the volume on the Subwoofer for the best listening experience.
Fluance offers matching subwoofers for the ultimate audio experience.
For more information visit:
Fluance.com/subwoofer
Volume Adjustment
Turn the Control Knob or use the Remote to increase or decrease volume.
EQ Adjustment
Use the Bass/Treble buttons on the Remote to adjust each from -5 to +5.
LED Behavior:
| Red (Flash 2x) – Bass/Treble Set to -5 or +5
---|---
| Bluetooth: Blue (Flash 2x) – Bass/Treble set to 0
| RCA: Green (Flash 2x) – Bass/Treble set to 0
| Optical: White (Flash 2x) – Bass/Treble set to 0*
*NOTE: The Status LED will flash the input color when Bass/Treble is set to 0.
Adjusting Source LED Brightness
Use the LED Brightness Button on the Remote to cycle between 100%, 25%, and
OFF brightness levels.
NOTE: When set to OFF, the LED will turn on for 5 seconds when power is
turned on or new Source is selected, before turning off again.
Frequently Asked Questions
What is ˝auto-pairing˝ and how does it work?
Auto-pairing is a convenient connection feature included in all Fluance
Bluetooth® Speakers. If the connected Bluetooth®-enabled device leaves the
connection range of the Ai41 and returns at a later time, the device will
automatically connect. If the device’s Bluetooth® function is disabled and
then enabled at a later time, the device will automatically connect as well.
*Note: The Fluance Ai41 will only auto-pair to the last device that it was connected to.
How do I change the source on my Fluance Ai41?
Press the Control Knob or use the Source button on the Remote Control. The LED
will change to the Source LED color (Blue/Green/White).
How do I adjust the Volume on my Fluance Ai41?
Turn the Control Knob or use Volume buttons on Remote Control. The LED will
flash Red at Max.
How do I adjust the LED Brightness?
Use the LED Brightness Button on the Remote to cycle between 100%, 25%, and
OFF brightness levels.
Another Bluetooth® device is connected to my Fluance Ai41 and I want to
connect my device.
You can reset any Bluetooth® connection by pressing the Bluetooth® Pairing
Reset button on the back of the Active Speaker. You can also press and hold
“Play/Pause” on the Remote for 3 seconds.
What RCA devices can be connected to the Ai41?
Any RCA device will work with the Ai41. Common devices would be TV’s,
Turntables, Smartphones, or Tablets.
How can I increase the volume when using the Ai41 with a turntable?
If turntable audio is too quiet you may need to add a preamplifier. Some
turntables have built in preamps which can be turned on or off. The Fluance
PA10 preamplifier is a great match for Fluance powered speakers and
turntables.
Why is the volume from each input different on the Ai41?
Ensure that any volume and EQ settings on your source devices are set to
similar levels. The different signal types used by each input means they are
processed differently by the Ai41. The Optical Input uses a digital signal
while the RCA Input uses an analog signal. These differences can result in
slight variances in the output volume of the Ai41.
How do I stop screeching or high pitch noise when using Optical Input?
Confirm the optical cable is fully inserted on both ends. Also, ensure that
the source device’s audio output format is set to PCM or Stereo.
Troubleshooting
No Power
- Ensure the LED Brightness is not set to OFF
- Check all connections on power adapter and ensure fully inserted
No Audio
- Check volume on Ai41 and ensure it is above 0
- Check volume on source device and ensure it is above 0
- Confirm Ai41 is set to correct source
- Ensure all cables are connected properly and fully inserted
No Audio from Passive Speaker
- Check speaker wire connections between speakers and ensure securely connected to binding posts
Poor Audio
- Ensure the colored wires are connected to the corresponding colored binding posts on each speaker
- Test with another audio source device to determine source of issue
Hissing Noise
- Ensure the colored wires are connected to the corresponding colored binding posts on each speaker
- Test using different RCA or optical cables
- If using with a turntable, ensure the ground cable is connected properly
Specifications
SPEAKER CONFIGURATION| 2 Way – 2 Driver Bookshelf Speaker
System with Integrated Amplifier
---|---
BLUETOOTH| Yes; BT 5.0
INPUTS| RCA, Bluetooth, & Optical
TWEETER| 1 inch Silk Soft Dome Ferrofluid Cooled
WOOFER| 5 inch Woven, Glass Fiber Composite
Drivers with Butyl Rubber Surrounds
AMPLIFIER POWER| Class D 90 Watts Continuous Average
Output (2x 45 watts)
FREQUENCY RESPONSE| 35Hz – 20KHz (DSP Virtual Sound)
CROSSOVER FREQUENCY| 2800Hz Phase Coherent 12dB/Oct – PCB
Mounted Circuitry
TOTAL HARMONIC DISTORTION (THD)| <0.3% (THD+N 1%)
POWER| Input: 100-240V 50Hz/60Hz
SPEAKER WEIGHT| Active Speaker: 8.52 lbs (3.86 kg)
Passive Speaker: 7.44 lbs (3.37 kg)
DIMENSIONS (HxWxD)| 10.9 x 6.5 x 7.6 inches
27.7 x 16.5 x 19.3 cm
Certification Information
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. This equipment
complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body. The device has been evaluated to meet
general RF exposure requirement. The device can be used in portable exposure
condition without restriction.
IC Warning
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference, and 2) This device must accept any interference, including
interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Warranty Information
Thank you for choosing Fluance! We guarantee your investment in our products
is a solid one. High performance components combined with quality
craftsmanship allow us to maintain the highest possible production standards.
All items are guaranteed against defects in materials and craftsmanship.
Fluance has outstanding quality control; if something should go wrong with any
of our products, we will repair it free of charge within the warranty period.
If the product cannot be repaired, we will replace the product. If the product
has been discontinued, we will replace the product with either the newest
version of said product or current equivalent. In the event that Fluance
replaces a product under warranty, the replacement would only carry the
original warranty from the original date of purchase.
Warranty Period
The Fluance products below are warrantied for parts and labor for the stated
period from date of original purchase, and are subject to the terms and
conditions of the warranty. Any refurbished products that are discontinued
hold a 90 day warranty from the date of original purchase. Fluance warranties
are valid for the original owner and are non-transferable.
Home Audio Passive Speakers: Lifetime Warranty
Active or Powered Speakers: Two Year Warranty
HiFi Turntables: Two Year Warranty
Batteries (For Powered Speakers): One Year Warranty
Warranty Exclusions
- Products purchased from a dealer not authorized by Fluance.
- Products with the serial number defaced, altered or missing.
- Defects resulting from disaster, accident, abuse, misuse, lightning, power surges, neglect, unauthorized modification or water damage.
- Defect or damage as a result of repairs performed by a person or party not authorized by Fluance.
- Defects or damage occurring during shipping (claims should be made with the shipping company).
- Defect or damage as a result of connecting a product to an outlet with the incorrect voltage. Voltage converters must be used where applicable.
- Consumable parts including, but not limited to, batteries, styli, and rubber belts.
To Obtain Warranty Service
Should your product require warranty service, please contact us at
www.fluance.com/contact or call us at
1-888-617-6863 to set up a Return
Authorization. Products returned
without a valid Return Authorization number will be refused.
Fluance products must be returned in their original packaging. Our products
are packaged specially to protect them from any damage during shipping, and
without this packaging the return shipment could get damaged.
This warranty does not cover the shipping cost, insurance, or any other
incidental charges.
Products shipped for warranty service must be pre-paid by the customer, and
Fluance will cover the cost to ship the repaired or replaced product back to
the customer.
Thank you for your purchase of this Fluance® product.
We hope you enjoy your experience.
Questions?
Give us a chance to help, we’re just a click away.
| Fluance.com/resources
---|---
| Fluance.com/support
| Fluance.com/videos
| Fluance.com/contact
Don’t forget to register your product with us!
Fluance.com/registration
References
- Turntables, Home Theater Surround Sound Speaker Systems and Home Audio Products | Fluance
- Fluance Support Center
- Register your product | Fluance
- Powered Subwoofers | Fluance
- Fluance Support Center
- Fluance Support Center
- Turntables, Home Theater Surround Sound Speaker Systems and Home Audio Products | Fluance
- Fluance Support Center
- Powered Subwoofers | Fluance
- Fluance Support Center
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>