REDSHIFT SPORTS Arclight PRO Flat Smart LED Bicycle Pedals Instruction Manual

REDSHIFT SPORTS Arclight PRO Flat Smart LED Bicycle Pedals

Product Information

The Arclight Pedals are a set of pedals that come with light modules that provide visibility and safety while riding a bike. The pedals are designed to be screwed in using an 8 mm hex wrench, and it is recommended to tighten them to 35 Nm using a torque wrench to ensure that the pedals won’t become loose over time. The left pedal screws in by turning counter-clockwise, while the right pedal screws in by turning clockwise. It is important to correctly install the right vs. left pedals to avoid damage.

The light modules that come with the pedals have three modes:
Steady light, flash, and EcoFlash, with battery life ranging from 3+ hours to 36+ hours depending on usage and conditions. The pedals have an auto On/Off functionality that turns off the light modules after 30 seconds of no movement and enters standby mode. After 150 seconds of no movement, the light modules enter Sleep Mode, and after 24 hours on Sleep Mode, they completely shut off and need to be manually turned on by pressing the button. The light modules are compatible with Arclight Multi-Mount (sold separately) allows you to mount your Arclight light modules to be used as a front or rear visibility lights on additional locations such as the bike seat post or handlebars.

Product Usage Instructions

1. Screw in Arclight Pedals using an 8 mm hex wrench.
2. Tighten the pedals to 35 Nm using a torque wrench to ensure that the pedals won’t become loose over time.
3. Install the RIGHT vs. LEFT pedals correctly by screwing in the left pedal by turning counter-clockwise (while facing the left side of the bike) and screwing in the right pedal by turning clockwise (while facing the right side of the bike).
4. Remove Light Modules from the charger and insert them into the pedals.
5. Press the button on each light module to turn on and select the mode: First Press for Steady Light, Second Press for Flash, and Third Press for EcoFlash.
6. Inspect the pedals for wear, damage, or lose parts before each ride. Keep pedals properly maintained at all times.
7. If you have any questions about your new pedals, please contact Redshift Sports at support@redshiftsports.com.

To operate the light modules:

• Auto On/Off functionality: After 30 seconds without sensing movement, the light modules will turn off and enter standby mode. They will turn on again when slight movement is sensed.
• Sleep Mode: After 150 seconds without sensing movement, the light modules will enter Sleep Mode. They will turn on again when heavier movement is sensed.
• Shut Off: After 24 hours on Sleep Mode, the light modules will completely shut off and need to be manually turned on by pressing the button.
• Removing a Light Module: This will automatically turn it off. When it is inserted again, it will need to be turned on by pressing the button.
• Pressing and Holding the Button: Will power off the light module. Pressing the button again is the only way to turn it back on.

The light modules are also compatible with Arclight Multi-Mount (sold separately) which allows you to mount your Arclight light modules to be used as a front or rear visibility lights on additional locations such as the bike seat post or handlebars.

ARCLIGHT PRO FLAT SMART LED BICYCLE PEDALS INSTALLATION INSTRUCTIONS
For the most up-to-date instructions, instructional videos, and additional resources, visit www.redshiftsports.com/instructions.

COMPATIBILITY:
Arclight pedals use standard 9/16in threaded spindles and will attach to any bicycle crank accepting this size.

Tool Needed

• Bike grease
• 8 mm hex wrench

NOTE:
If you do not own these tools, or do not feel comfortable performing these instructions, please visit your local bike shop for help. This is a 2-minute job with the right tools and experience!

INCLUDED

• 2x Arclight PRO Flat Pedals (Left+ Right)
• 4x Arclight Light Modules
• 1xArclight USS Charging Hub
• 2x spare traction pins
• 1x traction pin wrench

BEFORE YOU START

Remove Arclight Light Modules from pedals
Slide all four light modules out of the pedals.

Charge all Arclight Light Modules
Use the included charging hub, or plug a light module into any female USB slot. The indicator light on each light module will switch from orange to green when they are fully charged. After 10 minutes, the green light will shut off.

NOTE: The battery life will vary depending on usage and conditions.

Installation

STEP 1:
Unscrew your old bicycle pedals using a hex wrench or pedal wrench.

STEP 2:
Apply bike grease to the threads on both pedals

STEP 3:

Identify Left and Right Pedals
The left pedal will have a groove on the spindle, near the threads. The right pedal will not have a groove.

NOTE:
The redshift logo on the pedals will be legible when the Right and Left are oriented correctly. If the logo is upside down, the Right and Left are mixed up.

STEP 4:

Screw in Arclight Pedals using 8 mm hex wrench
It is recommended to then tighten to 35 Nm using a torque wrench to ensure the pedals won’t become loose over time.

LEFT
Left pedal screws in by turning counter-clockwise (while facing the left side of the bike).

RIGHT
Right pedal screws in by turning clockwise (while facing the right side of the bike).

CAUTION:
It’s VERY IMPORTANT to correctly install the RIGHT vs. LEFT pedals. Incorrectly switching them and cross-threading will lead to damage! If the pedals are not going in easily by hand for the first few turns make sure to check you have the correct pedal.

STEP 5:
Remove Light Modules from charger and insert it into the pedals

STEP 6:
Press the button on each light module to turn it on and select mode.

The light module will automatically switch from white to red depending on the orientation of the pedal — no user input is needed (as long as the correct RIGHT/LEFT pedal/wing is installed. See Step 1 – F for more details).

NOTE: Battery life will vary depending on usage and conditions.

Safety guidelines for pedals

Inspect the pedals for wear, damage or lose parts before each ride. Keep pedals properly maintained at all times. If you have any questions about your new pedals, please contact Redshift Sports at support@redshiftsports.com.

OPERATION TIPS

Auto On/Off functionality

• Standby Mode — After 30 seconds without sensing movement, the light modules will turn off and enter standby mode. They will turn on again when slight movement is sensed.

• Sleep Mode — After 150 seconds without sensing movement, the light modules will enter Sleep Mode. They will turn on again when heavier movement is sensed.

• Shut Off — After 24hrs on Sleep Mode, the light modules will completely shut off and need to be manually turned on by pressing the button.

• Removing a Light Module
  Will automatically turn it off. When it is inserted again, it will need to be turned on by pressing the button.

• Pressing and Holding the Button
  Will power off the light module. Pressing the button again is the only way to turn it back on.

ALSO COMPATIBLE WITH:
Light Modules are compatible with Arclight Multi-Mount (sold separately) The Multi-Mount allows you to mount your Arclight light modules to be used as a front or rear visibility lights on additional locations such as the bike seat post or handlebars.

Warning:

• This product is not guaranteed to prevent accidents or keep you visible from motorists in all situations.
• Please follow your local traffic laws and always use your best judgment when sharing the road with cars.
• This product may not comply with some European bicycle light laws such as StVZO regulations in Germany. This product should only be used for off-road applications in such jurisdictions.
• Arclight lights are designed to increase your visibility to others and are not intended to be used as a headlight or navigational light.
• In order to maintain battery health, always maintain the light modules charged. Failure to charge after depleting the battery may degrade the battery’s lifetime.
• Regularly clean and inspect all surfaces of the pedal (especially after a crash or hard impact) for hairline cracks or signs of damage. Immediately cease use of the component if cracks or signs of damage are found and contact Redshift Sports customer service.
• Be mindful of traction pins. They are sharp and can cause injury.
• Failure to follow these instructions and warnings may result in malfunction or breakage of this product, possibly causing serious injury or death.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>