SUNELL SN-IPR5150DUAS Bullet Network Camera User Guide

SUNELL SN-IPR5150DUAS Bullet Network Camera

Product Information

The Easy Network Camera is a device that enables electronic surveillance in public places. The camera comes with a quick setup guide, nameplate, and accessories. It is important to strictly observe the rules and precautions stated in the user manual to avoid device damage, data loss, device performance deterioration, or unpredictable results.

Product Precautions

• Fully understand the user manual before using the device.
• Provide an eye-catching notice in public places where the device is installed.
• Strictly observe installation requirements when installing the device.
• Conform to local electrical safety standards and use power adapters marked with the LPS standard.
• Use accessories delivered with the device and ensure voltage meets input voltage requirements.
• Ground the device if installed in places with unsteady voltage.
• Avoid heavy loads, intensive shakes, and soaking during transportation and storage.
• Protect the device from fall-down and intensive strikes, keep away from magnetic field interference, and do not install in places with shaking surfaces or under shocks.
• Clean the device with a soft dry cloth and slight neutral cleanser for stubborn dirt.
• Do not jam the ventilation opening and keep away from heat sources and strong electric radiation.
• Take insect- and moisture-proof measures if installed outdoors to avoid circuit board corrosion that can affect monitoring.
• Remove the power plug if the device is idle for a long time.
• Check whether the fragile sticker is damaged before unpacking.

Product Special Announcement

• All complete products sold by the manufacturer are delivered after strict inspection and come with a nameplate, quick setup guide, and accessories.
• The manufacturer regularly updates the software and hardware described in the manual without prior notice.

Product Usage Instructions

Before using the Easy Network Camera, read and fully understand the user manual. Follow the precautions stated in the user manual to avoid device damage, data loss, device performance deterioration, or unpredictable results. If installing the device in public places, provide an eye-catching notice. Strictly observe installation requirements when installing the device to avoid device damage caused by non-conformance to these requirements. Conform to local electrical safety standards and use power adapters marked with the LPS standard when installing and using the camera to avoid device damage.

Use accessories delivered with the device and ensure voltage meets input voltage requirements. Ground the device if installed in places with unsteady voltage. Protect the device from fall-down and intensive strikes, keep away from magnetic field interference, and do not install in places with shaking surfaces or under shocks. Clean the device with a soft dry cloth and slight neutral cleanser for stubborn dirt. Do not jam the ventilation opening and keep away from heat sources and strong electric radiation. If installing the device outdoors, take insect- and moisture-proof measures to avoid circuit board corrosion that can affect monitoring. Remove the power plug if the device is idle for a long time. Check whether the fragile sticker is damaged before unpacking.

Precautions

Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip “You have entered the area of electronic surveillance” in an eye-catching place. Failure to correctly use electrical products may cause fire and severe injuries.

WARNING| It alerts you to moderate dangers which, if not avoided, may cause minor or moderate injuries.
---|---

**CAUTION**

| It alerts you to risks. Neglect of these risks may cause device damage, data loss, device performance deterioration, or unpredictable results.
  NOTE| It provides additional information.

WARNING

• Strictly observe installation requirements when installing the device. The manufacturer shall not be held responsible for device damage caused by users’ non-conformance to these requirements.
• Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged.
• Use accessories delivered with this device. The voltage must meet input voltage requirements for this device.
• If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out.
• When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device.
• Do not focus strong light (such as lighted bulbs or sunlight) on this device. Otherwise, the service life of the image sensor may be shortened.
• If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage.

CAUTION

• Avoid heavy loads, intensive shakes, and soaking to prevent damage during transportation and storage. The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart.
• Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks.
• Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into a slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.
• Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device.
• Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.
• Keep the device away from moist, dusty, extremely hot or cold places, or places with strong electric radiation.
• If the device is installed outdoors, take insect- and moisture-proof measures to avoid circuit board corrosion that can affect monitoring.
• Remove the power plug if the device is idle for a long time.
• Before unpacking, check whether the fragile sticker is damaged. If the fragile sticker is damaged, contact customer services or sales personnel. The manufacturer shall not be held responsible for any artificial damage of the fragile sticker.

Special Announcement

• All complete products sold by the manufacturer are delivered along with nameplates, quick setup guide and accessories after strict inspection. The manufacturer shall not be held responsible for counterfeit products.
• The manufacturer will update this manual according to product function enhancement or changes and regularly update the software and hardware described in this manual. Update information will be added to new versions of this manual without prior notice.
• This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product, the final interpretation of company is as a standard.
• This manual is only for reference and does not ensure that the information is totally consistent with the actual product. For consistency, see the actual product.

NOTE

• For more information, please refer to website.

Open Package Examination

Open the package, check the appearance of product for no obvious damage, and confirm the item list for table 1- 1 is consistent.

Table 1-1 Packing list

Device Structure

Device Port

NOTE: Different devices may have different multi-head cables; Please refer to the actual product.

Table 2-1 Multi-head 1cable description

light is on, the network connection is normal; The yellow light flashes when the data is transmitted.

Some models may not have the lights; Please refer to the actual product.

| Support PoE supply.
2| Power supply (DC 12V)| Connect to a 12V direct current (DC) power supply.|
 | SD card slot| Support SD card, it up to support 256G|
 | Reset button| Long press the reset button for 5s to restore to the original settings.|

Camera Dimensions

NOTE

• Different devices may have different dimensions; Please refer to the actual product.

Figure 2-2 Dimensions （Unit: mm）

Quick Configuration(e.g IE)

Login

• Step 1: Open the Internet Explorer, input the IP address of IP camera (default value is 192.168.0.123) in the address box, and press Enter. The login page is displayed as shown in figure 3-1.
  Step 2: Input the user name and password.

  • NOTE: The default user name is admin. The default password is admin. Change the password when you log into the system for first time to ensure system security.
  • You can change the system display language on the login page.

• Step 3:  Click Login icon, the main page is displayed.

Modify IP address

• Choose Setting > Network> IP, the Network page is displayed. Input the IP address in the IP Address box and click Apply as shown in figure 3-2.
• After the IP address is set successfully, please use the new IP address to log in the Web interface.

Browsing Video

To ensure the real-time video can be played properly, user must perform the following operation when you login the web at the first time: If user can view the video directly, you can ignore the step of adding trusted sites.

• Step 1: the Internet Explorer. Choose Tools > Internet options > Security > Trusted sites > Sites, in the display dialog box, click Add, as shown in figure 3-3.
• Step 2: In the Internet Explorer, choose Tool > Internet Options > Security > Customer level, and set Download unsigned ActiveX control and initialize and script ActiveX controls not marked as safe for scripting under ActiveX controls and plug-ins to Enable, as shown in figure 3-4.
• Step 3:  Download and install the player control as prompted.

NOTE

If the repair tips displayed when installing the control, please ignore the prompt, and continue the installation, during the installation, close the browser. After installation login again to enter the live view.

• To browse a real-time video, click Live View. The Live Video page is displayed, as shown in figure 3-5.

Description

• 1. User can view the live view.
• 2. Playback, if the device install the SD card, user can view playback recording
• 3. Click Setting into the setting interface, set the parameter of device.
• 4. Click Logout to exit the live view interface, user need to input password to login again.
• 5. The alarm, when the alarm action is happening, the icon will show.
• 6 and 7 to switch the stream.
• 8. Switch the aspect ratio. Double-click in the video area to enter the full-screen mode, and double-click again to exit.
• 9. Snapshot, the picture will save to local folder(Setting > Local ).
• 10. Record, click this and record the live view and save to local folder.
• 11. Click the icon to open the Image Setting page. On the Image Setting page, user can set image, scene, WB, day-night, nosie reduction, enhance image.
• 12. Audio, click open or close the audio.
• 13. Interphone, click open or close the interphone.

Day Night

• To set the encode parameters, choose“Setting> Image > Image”, the “Day Night” page is displayed, as shown in figure 3-6.

Infrared lamp & warm light mode

• Auto: The image will be colored when the light strength is strong; The image would be white-black when the light strength is low, the infrared lamp will be open. It will open the white light when capture the human body, if the human is disappear, the white light will be lasting 30s, the white light is be closed, infrared lamp will be open.
• Day Mode: The image always be colored, it will open the white light when the light strength is low.
• Night Mode: The image will be colored when the light strength is strong; The image would be white-black when the light strength is low, the infrared lamp will be open.

Infrared lamp mode

• Auto: The image will be colored when the light strength is strong; the image would be white-black when the light strength is low, the infrared lamp will be open.
• Day Mode: Never open the infrared lamp, the image is colored.
• Night Mode: Open the infrared lamp, the image is white and black.
• Timing: When the time reaches the setting time, the mode will be switched to night or day.

Motion Detection

• To set alarm information, Choose ”Setting > Alarm > Motion Detection”，the is displayed, as shown in figure 3-7.

Click Enable to enable the motion detection alarm.

• Event Actions: User can choose four modes to get the alarm messages.
• Area: Drag the mouse left to choose area to set many areas, double-click left button to delete areas.
• Schedule: Set the time of opening alarm.
  • Click to choose all day and all week.
  • Drag the mouse left button to choose hours.
  • Choose the hours one by one.

Maintenance

Choose “Setting > System >Maintenance” the “Camera Maintenance” is displayed, as shown in figure 3-8. User can reboot, update and reset the camera.

• Click Reboot, the message”Are you sure to restart?” is displayed, then click “OK”, the device is restarted successfully five minutes later.
• Click Update to update software, choose software and confirm to update.
• Click Reset, the message “Are you sure to reset?” is displayed, then click “OK”, the device is reset to the factory settings.

CAUTION: After you click reset, all parameters will be restored to the factory settings. Use this function carefully.

NO: 101-300-0627-01
Issue: 1.1

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>