Kaadas RX-B Lever Smart Lock User Manual

Kaadas RX-B Lever Smart Lock

Product Information – RX-B/RX-D Smart Lock

The RX-B/RX-D Smart Lock is a high-quality, durable lock designed to provide maximum security and convenience. The lock features a keypad cylinder, wireless module socket, reset button, manual mode, micro USB port, and reboot button. The exterior assembly measures 169mm(L)x157mm(W)x64.7mm(H), while the interior assembly measures 182.4mm(L)x157.5mm(W)x69.3mm(H). The lock operates on four AA alkaline batteries with an operation voltage of 4.6~6.0V and can last up to six months with 10 times open/close per day.

Product Usage Instructions

1. Preparing for Installation:
   Ensure that you have all the necessary tools and additional parts required for installation. Make sure your door is prepared before installation. Only drill an upper hole if you want the lock to have added stability. Refer to the provided template for drilling if needed.

2. Installation:
   Follow the steps below for installation:

   • Install the latch ensuring that the latch angle faces the door jamb.
   • Install the strike onto the door jamb.
   • Adjust the deadbolt if necessary. The bolt ships with the backset in a 2-3/8(60mm) position. If required, turn the bolt case and pull to extend to a 2-3/4 (70mm) backset position. The bolt must be in the retracted(unlocked) position when changing the backseat.
   • Install the cross-bolt.
   • Position the inside mounting plate by routing the cable and connector through the mounting plate’s cable hole. Secure both assemblies using 8/30 screws.
   • Install the keypad. Attach the cable assembly to the interior assembly PCB by lining up notches on top of the cable connector to slots on the PCB connector. Press the connector firmly using your thumbs until completely connected.
   • Secure using a screw through the interior assembly onto the mounting plate.
   • Install the interior assembly on the inside mounting plate.
   • Install the exterior lever and interior lever.

3. Programming:
   Follow the instructions provided to program your lock.

4. Warnings:
   Failure to follow these instructions could result in damage to the product and avoid the factory warranty. The accuracy of the door preparation is critical for the proper functioning and security of this product. Misalignment can cause performance degradation and lessen security. Care should be taken to ensure a long-lasting finish. When cleaning is required, use a soft, damp cloth. Do not install batteries until the lock is completely installed on the door.

Installation Guide

Specifications

Exterior assembly

Interior assembly

| |
---|---|---
Exterior assembly| 169mm(L)x157mm(W)x64.7mm(H)| Operation temperature：

-4°F to 129°F(-20°C to 55°C)

Interior assembly| 182.4mm(L)x157.5mm(W)x69.3mm(H)|
Battery(not included)| AA alkaline battery X 4

(Operation voltage: 4.6~6.0V)

| Last up to six mouth

(10 times open/close per day)

Preparing for Installation

Additional Parts
Optional Bolt Faceplate

Tools Needed
Door prep

• *  2-1/8” (54mm) hole saw

  • 1” (26mm) boring bit
  •  7/64” (2.5mm) drill bit
  • 3/8” (10mm) drill bit
  • Chisel&Hammer

Lock installation #2 Philips screwdriver

Important Notice:
Make sure your door is prepared prior to installation. Only drill an upper hole if you wish the lock to have added stability. Please refer to the provided template for drilling if needed.

• Measure the dimension of the hole shown.
• Change the faceplate, if necessary.
• Adjust the deadbolt.
  NOTE: Bolt ships with backset in 2-3/8”(60mm) position. If required, turn the bolt case and pull to extend to 2-3/4” (70mm)backset position. (see picture below).The bolt must be in a retracted(unlocked) position when you are changing the backset.

Installation

1. Install latch.
   

2. Install strike onto the door jamb. ****

3. Install cross-bolt. ****

4. Install keypad. ****

5. Position the inside mounting plate by first routing the cable and connector through the mounting plate’s cable hole. Secure both assemblies using 8/30 screws.
   

6. Attach cable assembly to the interior assembly PCB by lining up notches on top of the cable connector to slots on the PCB connector. Press the connector in firmly using your thumbs until completely connected. ****

7. Secure using a screw through the interior assembly onto the mouting plate.

8. Install interior assembly on the inside mounting plate.

9. Install exterior lever

10. Install interior lever

Congratulations, you have installed your new lock, now please follow the instructions to program your lock.

Warning

• Failure to follow these instructions could result in damage to the product and avoid the factory warranty.
• The accuracy of the door preparation is critical for the proper functioning and security of this product. Misalignment can cause performance degradation and lessening of security
• Finish Care: This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long—lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.

IMPORTANT: Do not install batteries until the lock is completely installed on door.

1. Master PIN Code (4-10 digits):
   The default master pin code is “12345678”, please modify it after installation. If you forget your master pin code, you can reset your lock back to factory settings

2. User PIN Code (4-10 digits):
   User pin codes can be set up through the master pin code. Up to 20 user pin code can be stored

3. Both master and user pin codes don’t support the following combination of numbers.

Add up User PIN codes

1. Touch the screen with your hand to activate.
2. Enter“*”twice and the Master PIN Code followed by “#”.
3. Enter “2”.
4. Enter “1”, add user PIN code.
5. Enter new User PIN code followed by “#”.
6. Repeat step 5 one more time.
7. To continue adding users,do previous steps 4-5 again.
   CAUTION
   When registering User PIN codes,the code must be entered within 10 seconds or time expires.No matter setting succeed or failed,the process won’t completedand stay at current stage,you can press “*”to return to previously menu.

Delete User PIN codes

1. Touch the screen with your hand to activate.
2. Enter“*”twice and the Master PIN Code followed by “#”.
3. Enter “3”, Lock Response: key“1”light up.
4. Enter “1” for deleted PIN code Voice guide.
5. Enter the PIN code, and confirm with“#”.
6. To continue deleting users,do previous steps 1-4 again.
   CAUTION
   When deleting User PIN codes,the User Number must be entered within 10 seconds ot time expires.No matter setting succeed or failed,the process won’t completed and stay at current stage,you can press “*” to return to previously menu. Deleting all User PIN codes could be done only by reseting the lock to fatory default settings.

Silent Mode(Speaker enable/disable)
Silent Mode feature can only be programmed through the Master PIN code or APP.

1. Touch the screen with your hand to activate.
2. Enter“*”twice and the Master PIN Code followedby “#”.
3. Enter “5”to set up languages.
4. Enter “1 or 2 or 3 or 4 or 5”to select voice guide language(Silent Mode disable),enter“6” to enable Silent Mode.

Bluetooth settings(only for RX-D)
Bluetooth feature can be programmed through the Master PIN code or APP.Bluetooth is disabled in factory default setting.

1. Touch the screen with your hand to activate.
2. Enter“*”twice and the Master PIN Code followed by “#”.
3. Enter “7”to enter Bluetooth settings.
4. Enter “1”to enable Bluetooth,Bluetooth will work continuously after opration.
5. Enter “2”to disabled Bluetooth,Bluetooth will shut down in 2 mins after touch keypad lights off for engrgy saving, it will back to work when touch keypad wakes up.

Definitions

• Master Mode:
  The master mode could be entered by entering[**+Master PIN Code+# ] to program the lock.

• Master PIN code:
  The master pin code is used for programming and for feature settings.

• Manual Mode:
  Manual mode is designed for high-traffic doors, when Manual mode is enabled, the door will be openable without PIN code or key, Manual mode could be disabled temporarily by press and hold any key on the keypad for 2 seconds from outside.

• Shutdown Time:
  The lock will shut down for a default of 3 mins and not allow operation after the wrong code entry limit (10 times) has been met. When the unit is in shutdown, the light will flash when you are trying to use keypad.

• Silent Mode:
  The beeper will not make any voice.

• Status indicators:
  Located on exterior assembly.

• User PIN code:
  The user pin code operates the lock. The maximum capacity of user pin codes is

• Reset button:
  After reset operation, the lock will be restored to factory default settings, all user credentials will be deleted. Refer to reset guide

Factory Default settings

Lock Operation

Change Master PIN code

1. Touch the screen with your hand to activate.
2. Enter “*”twice and the 4-10 digit Master PIN Code followed by “#”.
3. Enter “1”to change Master PIN Code.
4. Enter new 4-10 digit Master PIN Code followed by “#”.
5. Repeat step 4 one more time.

Before changing default Master PIN Code,all other setting menu will be disabled.You have te change Master PIN Code first,the do other lock settings.

Function extension settings (only for RX-D)
Network features are included in function extension,can only be programmed through the Master PIN code.

1. Touch the screen with your handto activate.
2. Enter “*” twice and the master PIN Code followed by “#”.
3. Enter “8″ to join network.
4. Enter “1″ to log in the network.
5. Enter “2″ to log out network.

If the lock is connected to a network controller, it is recommended that it is programmed through the centralized user interface(PC or hand-held device)to ensure communication between the lock and the controller

How to use

Unlock the door

• Unlock the door from outside the Master/User pin code or key.

Lock the door
Lock the door from outside

• Normal
  In Auto re-lock mode, the bolt will extend
  out automatically in 5 seconds after unlocking.

• Manual Mode
  Press any key on the keypad for 2 seconds.

Manual Mode Switch ****

• Enable: Move the switch to position to enable manual mode.
• Disable: Move the switch to position to disable manual mode.

Unlock with a Fake PIN code
Users can prevent pin code exposure from strangers by entering random digits before or after the pin code.

Reset to factory default settings

Operation on lock

1. Open the battery box and find the reset button.
2. User a sharp thing to press and hold the reset button.
3. Keep holding the reset button for 5 seconds until hearing the voice guide.
4. After that, all user data and settings will be deleted.

References

• Kaadas Official

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>