Sunell SN-IPV8040EDAR-Z Dome IP Camera Pro Series User Guide

Sunell SN-IPV8040EDAR-Z Dome IP Camera Pro Series

Vandal Dome Network Camera Quick Setup Guide

This Vandal Dome Network Camera is a surveillance camera designed for indoor and outdoor use. It is important to follow the precautions and usage instructions in this document to ensure proper installation and usage of the device.

Precautions

Before using this device, it is important to fully understand this document and strictly observe the rules provided. Failure to correctly use electrical products may cause fire and severe injuries.

• WARNING: It alerts you to moderate dangers which, if not avoided, may cause minor or moderate injuries.
• CAUTION: It alerts you to risks. Neglect of these risks may cause device damage, data loss, device performance deterioration, or unpredictable results.
• NOTE: It provides additional information.

Usage Instructions

Follow the installation instructions provided in this document when installing the device. It is important to:

• Ground the device: If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage.

• Avoid damages during transportation and
  storage: Avoid heavy loads, intensive shakes, and soaking to prevent damages during transportation and storage. The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart.

• Protect the device: Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks.

• Clean the device: Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.

• Do not jam the ventilation opening: Follow the installation instructions provided in this document when installing the device. Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.

• Avoid extreme conditions: Keep the device away from moist, dusty, extremely hot or cold places, or places with strong electric radiation.

• Protect against corrosion: If the device is installed outdoors, take insect- and moistureproof measures to avoid circuit board corrosion that can affect monitoring.

• Remove power plug: Remove the power plug if the device is idle for a long time.

It is important to strictly observe installation requirements when installing the device. The manufacturer shall not be held responsible for device damage caused by users’ non-conformance to these requirements. Also, strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged. When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device. Additionally, do not focus strong light (such as lighted bulbs or sunlight) on the device.

Precautions

Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip “You have entered the area of electronic surveillance” in an eye-catching place. Failure to correctly use electrical products may cause fire and severe injuries.

WARNING| It alerts you to moderate dangers which, if not avoided, may cause minor or moderate injuries.
---|---
  CAUTION| It alerts you to risks. Neglect of these risks may cause device damage, data loss, device performance deterioration, or unpredictable results.
  NOTE| It provides additional information.

WARNING

• Strictly observe installation requirements when installing the device. The manufacturer shall not be held responsible for device damage caused by users’ non-conformance to these requirements.
• Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged.
• Use accessories delivered with this device. The voltage must meet input voltage requirements for this device.
• If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out.
• When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device.
• Do not focus strong light (such as lighted bulbs or sunlight) on this device. Otherwise, the service life of the image sensor may be shortened.
• If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage.

CAUTION

• Avoid heavy loads, intensive shakes, and soaking to prevent damages during transportation and storage. The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart.
• Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks.
• Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.
• Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device.
• Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.
• Keep the device away from moist, dusty, extremely hot or cold places, or places with strong electric radiation.
• If the device is installed outdoors, take insect- and moistureproof measures to avoid circuit board corrosion that can affect monitoring.
• Remove the power plug if the device is idle for a long time.

Special Announcement

• All complete products sold by the manufacturer are delivered along with nameplates, quick setup guide and accessories after strict inspection. The manufacturer shall not be held responsible for counterfeit products.
• The manufacturer will update this manual according to product function enhancement or changes and regularly update the software and hardware described in this manual. Update information will be added to new versions of this manual without prior notice.
• This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product, the final interpretation of company is as a standard.
• This manual is only for reference and does not ensure that the information is totally consistent with the actual product. For consistency, see the actual product.

NOTE

• For more information, please refer to website.

Open Package Examination

Open the package, check the appearance of product for no obvious damage, and confirm the item list for table 1-1 is consistent.

Packing list

Device Structure

Device Ports

NOTE
Different devices may have different device ports, please refer to the actual product.

Interface of camera

Alarm/ Audio

| Alarm out/in| out A, alarm out A| Applied for alarm function
out B, alarm out B
G, ground
In, alarm in
Audio out/in| In, audio in|

Applied for audio function

Out, audio out
G, ground
Analog

video

| CVBS, analog video output|
G, ground
Network access port| Connects to a standard Ethernet cable|
12V power

supply

| The ports are 12V/ OUT/12V/IN.|
Over cable rubber stopper| Uses the auxiliary thread-line tool to through the cable|
Over function- cord rubber stopper| There are two rubber stoppers, user can use the tool to pierce the stopper, and plug all cords in.|

Camera Dimensions

NOTE
Different devices may have different dimensions, please refer to the actual product.

Figure 2-2 Dimensions of Dome(Unit:mm）

Device Installation

WARNING
To avoid moisture influence, install the dome cover at least half an hour after the camera is installed and powered on. The vandal dome camera can be installed in the ceiling , wall, wall bracket or ceiling bracket. This section describes how to install the camera in the ceiling.

Installation Steps:

• Step 1 Stick the Installation location sticker which is in accessory package on the ceiling or wall, Drill three holes based on the marks on the sticker. Drive the swell plastic buttons into the holes.

• Step 2 Use the wrench in the accessory package to unscrew the three screws on the dome cover. The camera is opened, as shown in figure 3-1. And use release the base panel

• Step 4 Connect the network access port and power supply of the multi-head cable with the tool as shown in figure 3-3.
  NOTE

• There are two outlet mode of cable, for the top outlet mode, user should drill the hole at first for threading cable.

• The side outlet mode that the installation sticker’s gap should align the outlet rubber stopper.

• Step 5 The set screw should be aligned the direction icon of base panel, then rotate the device clockwise to the extreme position, then tighten the set screw to lock block.

• Step 6 Connect the camera to monitor , loosen the screws of support frame, as shown in figure 3-5. Adjust the three axes to focus image on monitoring scenarios. Tighten the screws to finish adjustment.

• Step 7 Arrange the cable of camera to over-line buckle, then assemble the dome cover with hex wrench, as shown in figure 3-6.

NOTE

• During adjusting lens, the image might be blur, set the focus value in Sensor > Lens control page in web page.

Quick Configuration(e.g IE)

Login

• Step 1 Open the Internet Explorer, input the IP address of IP camera (the default value: 192.168.0.120) in the address box, and press Enter. The login page is displayed. as shown in figure 4-1 .
• Step 2 Input the user name and password.

NOTE

• The default user name and password both are admin. Modify the password when you login the system for the first time to ensure system security.
• It is advised to restart the device three minutes later after modifying the password to ensure modified successfully.
• User can change the system display language on the login page.
• Step3 Click Login, the main page is displayed.

Modify IP address
Choose Configuration > Device > Local Network, the Local Networkpage is displayed. Input the IP address in the IP Address box and click Apply as shown in figure 4-2. After  the success of the IP address setting, please use the new IP address to login the Web interface.

Browsing Video

To ensure the real-time video can be played properly, you must perform the following operation when you login the web for the first time:

• Step 1 The Internet Explorer. Choose Tools > Internet options > Security > Trusted sites > Sites, in the display dialog box, click Add, as shown in figure 4-3.
• Step 2 In the Internet Explorer, choose Tool > Internet Options > Security > Customer level, and set Download unsigned ActiveX control and initialize and script ActiveX controls not marked as safe for scripting under ActiveX controls and plug-ins to Enable, as shown in figure 4-4.
• Step 3 Download and install the player control as prompted.

NOTE

If the repair tips are displayed when installing the control, please ignore the prompt, and continue the installation, close the browser during installing. Then login the page again. To browse a real-time video, login the device and click Live Video. The Live Video page is displayed, as shown in figure 4-5.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>