MINIWARE MDP-L1060 DC Electronic Load Power Supply User Manual
- June 9, 2024
- Miniware
Table of Contents
MINIWARE MDP-L1060 DC Electronic Load Power Supply
Product Information
MDP-L1060 DC Electronic Load
The MDP-L1060 is a DC electronic load designed to test and evaluate DC power
sources such as batteries, power supplies, and solar cells. It can simulate
different load conditions and provide accurate measurements of voltage,
current, power, and resistance.
The device is equipped with a fan cooling system and over-current,over-
voltage, and over-temperature protection features to ensure safe and reliable
operation.
Product Usage Instructions
- Connect the power source to the load using cables or wires with appropriate ratings.
- Turn on the load by pressing the power button located on the front panel.
- Select the desired operating mode (CC, CV, CR, or CP) using the mode button.
- Adjust the load current, voltage, or power using the corresponding knobs or buttons.
- Monitor the measurements displayed on the screen, including voltage, current, power, and resistance.
- If necessary, enable the protection features by pressing the corresponding buttons to prevent damage to the load or the power source.
- Turn off the load by pressing the power button again and disconnect the cables or wires.
Note: Always follow the safety precautions and guidelines provided in the
user manual. Do not exceed the maximum ratings of the load or the power
source. Use appropriate protective equipment such as gloves and goggles when
handling high voltages or currents.
Do not modify or tamper with the device without proper authorization or
training.
Product Name
MDP-L1060 DC Electronic Load
User File
Buyer Name
Contact Number
Email
Purchase Date
Warm reminder
- Please keep this Warrenty Card and visit www.morningtools.com for future customer service;
- For product details and User Manual, please visit www.miniware.com.cn.
Warranty
- This Product has a 12—month warranty. During the warranty period, if Product fails or is damaged under correct operations, Product can be repaired or replaced for free. If the warranty period is exceeded, certain maintenance cost would be charged.
- During warranty period, if following occurs, certain maintenance cost will be charged or after-sales service might be even refused:
- Failure to follow Safety Instructions or User Manual that results in product failure or damage;
- Product failure or damage caused by unauthorized disassembly, repair or modification.
Manufacturer name: Guangzhou e-Design Intelligent Technology Co., Ltd.
Manufacturer address: Room 3308, Holdround Plaza, DaNan Road, YueXiu
District, GuangZhou City, GuangDong Prov., China
Importer name: EXP GmbH
Importer address: Schroten 8, Saarbrucken, Germany
FCC STATMENT
Caution: The user is cautioned that changes or mcxlifications not
expressly approved by the party responsible for could void the user’s
authority to operate the equipment.
This device cnmplies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may undesired operation.
NOTE: This equipment has been tested and found to cnmply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Statement:
This equipment complies with FCC radiation exgx)sure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>