WAVE Bing ES29 Earbuds User Manual
- June 12, 2024
- WAVE Bing
Table of Contents
WAVE Bing ES29 Earbuds User Manual
Thank you very much for choosing the ES29 Bluetooth earphones. To have a great experience, please read this manual carefully before use.
Button definition
This product supports automatic master-slave switching, the headset uses a touch structure design, and the key operation instructions are as following
Operations
Bluetooth connection
TWS Mode:
- a Automatic boot, automatic pairing Earbuds will automatically turn on and prompt out “power on” and try to connect each other, once they have been taken out from the charging case.
- b When the pairing is successful
LED indicators on the L earbuds will blinking alternately ,and LED indicators turned off on the R earbuds.
- c Connect mobile phone
User can turn on Bluetooth function of the smart phone and search for the
Bluetooth device “Wave Buy” for pairing, And LED
indicators turn off on the left earbuds once they connected with the smart
phone.
Single earbud mode:
a Take out any earphone of the left or right from the charging case, the LED indicator will blinking alternately
b smart phone for pairing
The user can search for “Wave Buy” with a smart phone for pairing. The device
will prompt “Connected”, The pairing is successful, and the light will be
turned off.
Note: The left and right earbuds will be turned on at the same time when the
charging case is opened. When using the single earbud mode, the other earbud
needs to be turned off (manually power off or put it in the charging case and
close the top cover of the charging case).
Automatic reconnection:
After the earbuds is successfully connected to the terminal device, the next
time the earbuds is turned on, it can automatically connect back to the
terminal device that was connected last time.
Incoming call
Charging
Charge the earbuds
- Earbuds will prompt out low battery voice alert once the battery level is too low.
- Put the L/R earbuds in the charging case and close the charging case cover, the earbuds will automatically enter the charging mode and the white light display.
- Earbuds full charge time: 1.5 hours, the white charging indicator light turns off after the earphone is fully charged.
Reset to factory default
- You can reset earbuds to factory default if you encounter pairing problems. When the earbuds off , tap and hold for 10 seconds to reset them to factory default. Put them back to the charging case and take out again for pairing.
Technical Parameters
- Chipset: Actions
- Input charging voltage and current: 5V/1A
- Battery type: built-in rechargeable lithium battery
- Battery capacity: earbuds 40mAh*2, charging case 300mAh
- Frequency response range: 20HZ-20KHZ
- Sensitivity: 99+- 3dB
- Bluetooth version: V5.0
- Working range: 10M
- Working hours: Earbuds: 4H
ATTENTION With the software and hardware updated, all the technical data and the mode of operation showed on the manual could be changed without prior notice.
Security warning:
- Please store and use the product under normal temperature, do not expose this apparatus to the rain or moisture .
- Do not throw away or disassemble for repair as it may cause safety problem
- Built-in lithium battery, do not discard or put it into a fire
- For your health and to extend the life of the product, better not to keep maximum volume on, to avoid injury of your hearing.
- In any emergency, Cut off the power immediately
- To always have a better performance, please charge in time once the battery is low.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement The device has been evaluated to meet general
RF exposure requirement. The device can be used in portable exposure condition
without restriction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>