QSFPTEK S5300-48T6X 48 Port Ethernet L3 Switch User Guide
- June 9, 2024
- QSFPTEK
Table of Contents
QSFPTEK S5300-48T6X 48 Port Ethernet L3 Switch
Introduction
The S5300-48T6X is a next-gen aggregation switch, features 48x GE RJ45 downlinks and 6x 1 OGE SFP+ uplinks. It supports stacking of up to eight S5300 series switches, making them logically regarded as one switch for interconnection and management.
We appreciate your decision to select S5300-48T6X. This manual is intended to help you become acquainted with the switch design a nd provide instructions for implementing the switches into your network.
Accessories
-
Power Cord x1
-
Console Cable x1
-
Mounting Bracket x2
-
M3 Screw x8
-
Rubber Pad x4
Hardware Overview
Front Panel Ports
| Parts | Description |
|---|---|
| Gigabit Ethernet Port | RJ45 interface, with LINK/ACT indicators |
| 10G GE Port | SFP+ interface, with LINK/ACT indicators |
| CON Port | A baud rate of 9600bps , RJ45 interface |
Front Panel LEDs
| LEDS | Description |
|---|---|
| SYS LED | If the SYS indicator flickers, the system works normally. |
| PWR LED | If the PWR indicator is always on, the device is powered on. |
Back Panel
| Abbrev | Name | Description |
|---|---|---|
| Grounding column | The grounding column | The grounding column must be fine. |
| POWER | AC power supply | Input voltage: AC 100~240V |
Installation Requirements
Tools Preparation
- Screwdriver
- Static-proof wristband
- Bolt
- Ethernet cable
- Other Ethernet terminal devices
- Control terminal
Safety Principles
- Keep dustless and clean during or after the installation.
- Put the cover at the safe place.
- Put tools at the right place where they are not easily falling down.
- Put on relatively tight clothes, and fasten the tie or scarf well and roll up the sleeve, avoiding stumbling the machine box.
- Put on the protective glasses if the environment may cause damage to your eyes. Avoid incorrect operations that may cause damage to human or devices.
Site Environment
- Make sure that the workshop is well-ventilated, the heat of electrical devices is well-discharged .
- Avoid to damage devices by following the electrostatic discharge prevention procedure. S5300-48T6X Hardware Installation Manual.
- Put the machine box at the place where cool air can blow off the heat inside the machine box. Make sure the machine box is sealed.
Mounting the Switch
Connecting the Power
- Plug the AC power cord to the switch power port on the back rear.
- Connect the other end of the power cord to a AC power source equipment.
Connecting the RJ45 Ports
- Connect one end of the Ethernet cable to the RJ45 port on networking equipment, such as PC, printer, server, storage, etc.
- Connect the other end of the Ethernet cable to the switch RJ45 port.
Connecting the SFP+ Ports
- Insert the SFP+ module into the SFP+ port.
- Plug a fiber patch cable to the SFP+ transceiver.
- Connect the other end of the fiber to the device that you want to realize data communication.
Connecting the Management Ports
Connecting the Console Port
- Prepare an console cable.
- Insert the RJ45 connector of the console cable into the console port on the switch.
- Connect the D89 female connector on the other end of the console cable to the serial port on the computer host.
Configuring the Switch
Configuring the Switch Using the Web-based Interface
Step 1: Connect your computer to the switch using an Ethernet cable and
open a web browser.
Step 2: Set the IP address of the computer to 192.168.0.x (where “x” is
any number from 2 to 254) and the subnet mask to 255.255.255.0.
Step 3: Open a web browser and type http:/1192.168.0.2 in the address bar. Enter the default username and password (admin/admin).Step 4: Click sign- in to access the web-based configuration page.
Configuring the Switch Using the Console Port
Step 1: Use the console cable to direct connect the switch console port
to your computer.
Step 2: Launch the terminal simulation software such as Hyper Terminal on
the computer.
Step 3: Configure the parameters of the terminal emulation software as
follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit, and no flow
control.
Step 4: Enter the default username and password (admin/admin).
Troubleshooting
Hardware Fault Analysis
Power and cooling systems-power and fan Port, cable and connection-ports on the front panel of the switch and the cables connecting these ports
Faults Relative with Power and Cooling System
Do the following checkups to help remove the fault:
- When the power on-off is at the “ON” location, check whether the fan works normally. If the fan does not work well, check the fan.
- if the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section 2.3 “Requirements for Common Locations”.
- If the switch cannot be started and the PWR indicator is off, check the power.
Faults Relative with Port, Cable and Connection
Do the following checkups to help remove the fault:
- If the port of the switch cannot be linked, check whether the cable is correctly connected and whether the peer connection is normal.
- If the power on-off is at the “ON” location, check the power source and the power cable.
- If the CLI port does not work after the system is started up, check whether the CLI port is set to a baud rate of 9600 bps, eight data bits, no sum check bit, one stop bit and no traffic control.
Support and Other Resources
- Contct us https://www.qsfptek.com/company/contact-us.html
- Email sales@qsfptek.com
- Customer Success https://www.qsfptek.com/resources/customer-success-stories
Product Warranty
S5600 series switches are backed by a 5-year limited warranty supported by
QSFPTEK. And you are eligible to apply for a return or e xchanqe of your items
within 14 days of receiving them.
For more details about applying qualifications, please live chat or email
sales@qsfptek.comforsupport
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>