Swim Fun SPS50-1 250 Watt Pump for Pools and Hot Tubs User Manual

Swim Fun SPS50-1 250 Watt Pump for Pools and Hot

Product Information

The Pump for Pools and Hot Tubs comes in three different models: SPS50-1 (1634) with 250 watts, SPS75-1 (1018) with 450 watts, and SPS100-1 (1019) with 550 watts. The pump has a drainage valve, pump housing, suction cover hose connection, suction flow connector, discharge flow connector, screw hole, and base for fitting. It has a maximum capacity of 117 liters/minute and a maximum head of 10 meters. The pump is classified as IPX5 with safety class B or F, depending on the model.

Product Usage Instructions

1. General Instructions: Do not use the pump when there are bathers in the pool if the pump is not permanently fitted. The pump must be earthed and attached to an earthed power supply that is protected by a residual-current device (RCD) or residual-current circuit breaker (RCCB) with a nominal residual operating current of less than 30 mA.
2. Fitting: Hose connectors must be sealed using Teflon tape to prevent air from being sucked in. Keep hose lengths as short as possible to reduce pump capacity. Ensure that there is an adequate supply of water, and the water discharge connection on the suction side must always be immersed in water. All hose connections must be sealed with Teflon tape, and we recommend using at least 15 rounds of tape. All hose parts must be able to withstand internal pressure and fitted responsibly.
3. Main Power Connection: The pump has a risk of electric shock. Ensure that the pump is attached to an earthed power supply that is protected by a residual-current device (RCD) or residual-current circuit breaker (RCCB) with a nominal residual operating current of less than 30 mA.
4. Before You Start: After installation, fill the pump’s filter with water to prevent a dry run that could damage the pump. Ensure that the suction hose and filter are filled with water. Depending on the suction hose’s length and diameter, reaching full pressure may take some time. Remove the transparent filter cover, fill the filter with clean water, ensure that the suction hose is filled with water, and make sure that the nozzle or tap on the pressurized hose is open so that air can escape as the pump fills.
5. Safety: Always follow safety precautions when using the pump, and refer to the troubleshooting section of the manual if there are any issues. For winter storage, drain the pump and store it in a dry place.
6. Guarantee: The pump comes with a guarantee, and spare parts are available for replacement if necessary.
7. Responsible Disposal: Dispose of the pump responsibly according to local regulations.

Description

1. Drainage valve
2. Pump housing
3. Suction cover hose connection
4. Suction flow connector
5. Discharge flow connector
6. Pump cover
7. Screw hole
8. Base for fitting

Technical specifications

General instructions

We do not recommend the pump working with water that is over 35 degrees for a long period of time. The purpose of these instructions is to ensure correct installation and optimal performance of the pump. The pump is designed for use with clean water up to a maximum temperature of 35°C. All the materials used are of high quality and production processes are subject to stringent controls. To prevent overloading the motor and damage due to incorrect installation, please comply with the-se guidelines and install the pump in accordance with the technical specifications. We accept no liability for the consequences if the pump is installed and used incorrectly.
If the pump is not permanently fitted, it must not be used when there are bathers in the pool. The pump must be earthed and attached to an earthed power supply protected by a residual-current device (RCD) or residual-current circuit breaker (RCCB) with a nominal residual operating current of less than 30 mA.

Fitting

Hose connectors must be sealed using Teflon tape. If connectors are not correctly sealed, air will be sucked in. Air inside the pump impairs or prevents pressure accumulation inside the pump. Keep hose lengths as short as possible. Excessive hose lengths reduce pump capacity. Always en-sure that there is an adequate supply of water. The water discharge connection on the suction side must always be immersed in water.
All hose connections must be sealed with Teflon tape to prevent leaks. We recommend at least 15 rounds of tape.
All hose parts must be able to withstand internal pressure.
All hose parts must be fitted responsibly.

Main power connection

DANGER Risk of electric shock!

• The pump must be a least 3.5 meters from the pool edge.
• The pump must be earthed and attached to an earthed power supply protected by a residual- current device (RCD) or residual-current circuit breaker (RCCB) with a nominal residual operating current of less than 30 mA.
• When used outdoors, the pump must be placed on a firm, level and well-drained surface. The electrical connections must be protected from splashes: connections must never come into contact with the water.

Before you start

TAKE CARE!
After installation, loss of water or suction of air into the pump, the pump’s filter must be filled with water. A dry run will damage the pump!
NB!
Suction hose and filter MUST be filled with water. Depending on length and diameter of the suction hose, reaching full pressure may take some time.

1. Remove transparent filter cover.
2. Fill filter with clean water.
3. Make sure that the suction hose is filled with water and that the water flows freely to the pump.
4. Make sure that the nozzle or tap on the pressurized hose is open so that air can escape as pressure builds.
5. Start the pump.
6. Switch off the pump when there is a steady flow of water.

Safety

Specific uses
This pump is specially designed to circulate water in swimming pools. It must not be used to pump drinking water or food products. It must not be used to pump explosive, inflammable, aggressive fluids or substances which are hazardous to health, or salt water containing more than 4% salt.
This pump is not suitable for commercial or industrial use. Changes to the pump or the use of parts that are not approved by the manufacturer are strictly prohibited. The manufacturer accepts no liability for damage caused due to inappropriate use of the pump.
General safety instructions
Never allow children, adolescents and anyone who is not acquainted with these instructions to operate the pump. Always comply with applicable local regulations regarding water supply and waste water. The following risks exist in principle when using any pump or pressurized container. They cannot entirely be eliminated – even when safety devices are used.
Hazards caused by immediate surroundings!

• Should not be exposed to persistent rain.
• Should be placed on a firm and even surface, which is dry and well-drained.
• Never place the pump in the vicinity of inflammable liquids or gases.

DANGER Risk of electric shock!

• Never aim a jet of water directly at the pump or other electrical parts! Risk of fatal electric shock!
• Never touch the electrical plug if your hands are wet! To disconnect, pull on the plug – not on the cable.
• The earthed plug or the plug’s connection to an extension lead must be placed in an area that is not subject to flooding.
• Always use heavy duty 1.5 mm2 extension leads. Always roll out cable reels to FULL extent.
• NEVER fasten, crush, pull or drive over electrical cables and extension leads. Protect leads from sharp objects.
• Place extension leads well AWAY from the water to be pumped.
• Never use a damaged cable. It should be replaced by the manufacturer, an authorised service centre or a qualified technician.
• Remove plug from socket before servicing the pump.
• This pump is not intended for use by anyone (including children) who has impaired physical, sensory or mental capacity or anyone who lacks the required experience and knowledge, except under supervision or after training in the use of the device by a person, who is also responsible for their safety.
• Keep a watchful eye on children: Never allow children to play with the device.

Dangers in connection with pump failure

• If you observe that the pump has been damaged in transit, notify your supplier immediately. Do not use the pump!
• Before using the pump, check the pump, and especially the electrical cable and plug, for defects and damage. Risk of fatal electric shock!
• A defective pump must be repaired by a qualified technician. Never use a defective pump!
• Never attempt to repair a pump yourself! Only qualified specialist technicians are permitted to service and repair pumps and pressurised containers.

Troubleshooting

The pump does not suck properly or is very noisy.

• Insufficient water: Make sure that the water supply is adequate.
• The suction hose is leaking: Seal hose connectors with Teflon tape and tighten hose clamps.
• The pump is not at the same level as the pool bottom (it should always be level with pool bottom).
• Filter basket inside the pump is blocked.

Rate of suction too high
Never exceed maximum rate of suction. The pump should always be level with the pool bottom.
Pressure is too low:
The suction hose is leaking or suction rate too fast.
Winter storage
Drain all the water from the pump drain valve. Store the pump in a dry, frost-free place. The filter MUST also be empty; Open the filter drain valve. Pump and filter tank are not frost-proof. Frost da-mage is not covered under the guarantee. Set filter handle in WINTERIZE position.

Guarantee

The product is covered by a 12-month guarantee (plus 12-month right to claim). The guarantee period applies from the purchase date stated on the purchase receipt. Proof of purchase must be provided when claiming for service under the guarantee.
NB: Keep your purchase receipt in a safe place! The guarantee does not cover ordinary wear-and-tear, scratches, scuffs or cosmetic damage. Specifically, the guarantee does not cover damage caused as a result of:

• Incorrect use or handling, including frost damage occurring as a result of inappropriate storage.
• Falling from a height or collision
• Repairs, changes or similar conducted by a party other than a Swim & Fun Service Centre.
• Frost damage. The pump must be stored in a well-drained, frost-free place.

In the event of a complaint, contact your dealer. When delivering a defective article, the product must be packaged responsibly to protect it from damage in transit. As the sender, you are liable to ensure that the product is intact on arrival. If you want us to return the product to you, please notify us on your name, address, phone number and email address! Do not forget to tell us what is wrong with the product.
For more consumer information and tips, visit our website: www.swim- fun.com.
This manual is protected under the provisions of the Danish copyright legislation.
Swim & Fun A/S – hotline:
Denmark +45 7022 6856
Sweden +46 771 188819

Spare parts

Responsible Disposal

This symbol indicates that this product should not be disposed of with general house-hold waste. This applies throughout the entire EU. In order to prevent any harm to the environment or health hazards caused by incorrect waste disposal, the product must be handed in for recycling so that the material can be disposed of in a responsible manner. When recycling your product, take it to your local collection facility or contact the place of purchase. They will ensure that the product is disposed of in an
environmentally sound manner.
info@swim-fun.com
www.swim-fun.com

References

• Gifts for Him & Gifts for Her | Toys, Gifts & Clothing | Fun.com
• Funlight.dk | EN SUKKERFRI LÆSKEDRIK
• Pools, water care, and pool accessories
• Pools, water care, and pool accessories

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>