MERCUSYS MS106LP 6-Port 10-100Mbps Desktop Switch Installation Guide

MERCUSYS MS106LP 6-Port 10-100Mbps Desktop Switch

LED Explanation

Power
On: The power is on
Off: The power is off

Link/Act Status
On: Link present but no activity
Flashing: Transmitting or receiving data
Off: No link

PoE Status
On: The port is providing PoE power
Off: The port is not providing PoE power

Switch Explanation

Recovery

Off: The PoE Auto Recovery function is disabled.
On: The switch will constantly detect the working status of a PoE powered device (PD).
When the switch finds that the PD works abnormally, the switch will reboot it.

Isolation

Off: Ports can transmit data with each other.
On: Ports 1-4 cannot transmit data with each other. They can transmit data only with the uplink ports (ports 5-6).

Extend

Off: Ports run at100/10 Mbps and support PoE power supply up to 100m away.
On: Ports run at 10 Mbps and support PoE power supply up to 250m away.

Connection

Notes:

1. PoE ports can also connect to non-PoE devices, but only transmit data.
2. Non-PoE ports (ports 5-6) are recommended to connect to uplink devices like routers.
3. Ports 1-2 have higher priority than other ports in transmitting data if network congestion occurs. It is recommended to connect key network devices (network cameras, APs, etc.) to ports 1-2.

Specifications

General Specifications

Port 1–4
Network Media (Cable)| 10BASE-T:2-pair UTP/STP (≤100m) of Cat. 3 or above 100BASE-TX:2-pair UTP/STP (≤100m) of Cat. 5 or above 1000BASE-T:4-pair UTP/STP (≤100m) of Cat. 5e or above
Switching Capacity| 1.2 Gbps
MAC Address Table| 2K
Forwarding Method| Store-and-Forward
MAC Address Learning| Automatically learning, automatically aging
Power Supply| External Power Adapter Input: 100-240 VAC, 50/60 Hz Output: 53.5 VDC/0.81 A
PoE Budget| 40 W (up to 30 W for each PoE port)

Environmental and Physical Specifications

Note 1：“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.
Note 2：“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3：The “－” indicates that the restricted substance corresponds to the exemption.

Safety Information

• Keep the device away from water, fire, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Place the device with its bottom surface downward.
• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended.
• Adapter shall be installed near the equipment and shall be easily accessible.

EU declaration of conformity

Mercusys hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.mercusys.com/en/ce/

Explanation of the symbols on the product label

Note: The product label can be found at the bottom of the product (and its .I.T.E power supply).

| For indoor use only
---|---

| Direct current

| Alternating current
| RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
| Energy efficiency marking (level VI)
| Polarity of d.c. power connector
| Class II equipment
| Caution
| Operator’s manual

Wall Mounting Specifications

Model| Screw Standard of ANSI B1.1| Minimum Length of Screw| Screw-Head-to- Wall Minimum Distance| Wall-Mounting-Holes Distance
---|---|---|---|---
MS105GP| 4#, (5#), 6#, 8#| 7mm| 1.5mm| 39mm
MS106LP| 4#, (5#), 6#, 8#| 7mm| 1.5mm| 39mm
MS108GP| 4#, (5#), 6#| 7mm| 1.5mm| 105mm
MS110P| 4#, (5#), 6#| 7mm| 1.5mm| 105mm

UK declaration of conformity

Mercusys hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility
Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
The original UK declaration of conformity may be found at https://www.mercusys.com/support/ukca/

CE Mark Warning

For technical support, replacement services, user guides, and other information, please visit https://www.mercusys.com/support/.

Frequently Asked Questions (FAQ)

Q1. Why is the Power LED not lit?****

The Power LED should be lit when the power system is working normally. If the Power LED is not lit, please check as follows:
A1: Make sure the AC power cord/power adapter is connected the switch with power source properly.
A2: Make sure the voltage of the power supply meets the requirements of the input voltage of the switch.
A3: Make sure the power source is on.

Q2. Why is the Link/Act LED not lit when a device is connected to the corresponding port?****

It is recommended that you check the following items:
A1: Make sure that the cable connectors are firmly plugged into the switch and the device.
A2: Make sure the connected device is turned on and working well.
A3: The cable must be less than 100 meters long (328 feet). If Extend Mode is enabled, it should be less than 250 meters (820 feet).

Q3. Why are PoE ports not supplying power for PoE devices?****

When the total power consumption of connected PoE devices exceeds the maximum, the PoE port with a smaller port number has a higher priority. The system will cut off power to the ports with larger port numbers to ensure supplying to other ports.
For example, if port 1, 2 and 4 are consuming 10 W respectively, and an additional PoE device with 15 W is inserted to port 3, the system will cut off the power of port 4 to compensate for the overload.

Q4. What should I notice before using the PoE Auto Recovery feature?****

A1: Before upgrading a connected PoE powered device (PD), disable PoE Auto Recovery to avoid the PD’s damage.
A2: When a PD does not send data packets to the switch for a long period in certain scenarios (e.g. an IPC in sleep mode), disable PoE Auto Recovery to avoid the PD repeatedly rebooting.

References

• Regulatory Compliance - Welcome to MERCUSYS
• UKCA - Welcome to MERCUSYS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>