MICROPOWER GROUP 24V-24V DC-DC Converter User Manual

June 10, 2024
MICROPOWER GROUP

MICROPOWER GROUP - logo DC/DC
CONVERTER
24V–24V / 40A & 60A
GALVANIC ISOLATED

MICROPOWER GROUP 24V 24V DC DC Converter -

CRITICAL INFORMATION

The technical data, information and illustrations have been carefully compiled and corresponds to the product status at the time of printing this manual. The manufacturer reserves the right to improve or modify the product, specifications, and documentation at any time without prior notice, if it is not considered necessary for technical
reasons.
Descriptions have been prepared very carefully and in detail, yet it is never possible to completely rule out wrong.
Under no circumstances will the manufacturer be held responsible for errors or damages resulting from wrong use or from misinterpretation.
The content of this documentation may not be copied, reproduced, translated, or otherwise passed on to third parties in any form without the express written consent of Micropower.

Warning!
Failure to follow these safety instructions could result in personal injury, property damage or impair the function of the product.
Danger! High voltage!
Failure to follow this safety instruction can result in injury or death or may damage or destroy the product.
Important Information!
To avoid operator error, read this manual carefully before installing and using the product and follow the appropriate instructions. Keep this manual near the product so that it can be referred to later.
This product is not intended for use by persons (including children) with reduced physical sensory or mental capabilities, or lack of knowledge or experience, unless they have received instructions or information on how to use the product by a person responsible for their safety. Children should be supervised to ensure that they do not play with the product.

USER MANUAL

  • Read this instruction before the DC/DC is taken into use.
  • Keep this manual within easy reach for the user of this DC/DC converter.

General
This product from Micropower is a highly efficient, intelligent, and very compact DC/DC charger with the latest switch mode technology in power conversion. Suitable for all DC applications where a secured and stable 27,2 VDC voltage is needed. The internal electronics controls input and output current and is both overload and short circuit
protected. All electronics are potted with polyurethane which makes the unit completely waterproof and very shock resistant.
The unit has no LED indications on the outside of the unit for black-out purpose as well as no ON/OFF function button. An external LED can be connected for Power ON indication.
As the unit acts like a stable power supply, the voltage will always be stable at 27.2 V as long as the input voltage is between 18–32 VDC and the unit will always be able to provide the specified current.
Installation
Check that the correct input voltage range and output voltage range matches the installation and the parameters mentioned on the DC/DC. The DC/DC enclosure is IP67, the internal electronics has a protective layer of lacquer. This brings the DC/DC suitable for indoor mounting, outdoor mounting in vehicles, in boats or built into the current
machine.
DC-in & out connection according to VG95234.

MICROPOWER GROUP 24V 24V DC DC Converter - connection

TECHNICAL SPECIFICATION

MODELL
Article number
Input voltage| MIL DC/DC 24-24V 60A
0060392
18–32 VDC| MIL DC/DC 24-24V 40A
0060391
18–32 VDC
---|---|---
Output voltage| 27.2 VDC| 27.2 VDC
Output current| 60 A| 40 A
Ambient temperature| –46 to 55 °C| –46 to 55 °C
Efficiency| > 95 %| > 95 %
DC-in connection| Glenair CA3102E| Glenair CA3102E
DC-out connection| Glenair CA3102E| Glenair CA3102E
Encapsulation| IP67| IP67
Measurements (W x L x H)| 160 x 144 x 101 mm| 160 x 144 x 101 mm
Weight| 2.5 Kg| 2.3 Kg

INCLUDED IN THE PACKAGE

MICROPOWER DCDC MANUAL

MICROPOWER GROUP 24V 24V DC DC Converter - connection1

MICROPOWER DCDC converter

MICROPOWER GROUP 24V 24V DC DC Converter -

WARRANTY

WARNING!
Do not use this product without reading the entire manual! Incorrectly installed or use of the product can sincerely damage the user, destroy the product or connected equipment. If the product is used the wrong way, warranty may be void.

  • Micropower warranty applies only to original purchaser within a period of 24 months from the date from delivery.
  • Micropower guarantees that the product is in excellent condition upon delivery, unless comes full refund.
  • If the user has not conducted a proper installation or used the product incorrectly applies no warranty.

Warranty claim
To take advantage of warranty please contact your retailer.
Please have following information available:

  • Receipt
  • Model number
  • Product serial number
  • A brief description of the malfunction

CONTACT INFORMATION
Micropower Group AB
Idavägen 1, SE-352 46 Växjö, Sweden
Phone: +46 (0)470-727400
e-mail: support@micropower.se
www.micropower-group.com

PRODUCT AND SUPPORT INFORMATION

For more information, visit Micropower Support Center:

MICROPOWER GROUP - qrhttps://docs.micropower-group.com/#

APPROVALS
Manufactured by: Micropower Group AB
The manufacturer declares that this product complies with applicable requirements. Complete declaration is available at Micropower Support Center: https://docs.micropower-group.com/Other docs

DIMENSIONS

MICROPOWER GROUP 24V 24V DC DC Converter - connection2

Doc: A04928 rev01
Print PN: 6540146
Idavägen 1 SE-352 46 | +46 470 72 74 00 | support@micropower.se

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals