Q ACOUSTICS E120 In Wall HiFi Amplifier Installation Guide
- June 10, 2024
- Q ACOUSTICS
Table of Contents
E120
INSTALLATION GUIDE
For models QI0120 & QI0122
www.audiovolt.co.uk
Important safety information and warnings
1 Notices
1.1 FCC Statement (for US Customers)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
1.2 FCC Radiation Exposure
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
CAUTION! Any Changes or modifications not expressly approved by Q Acoustics
could void the user’s authority to operate the equipment.
1.3 Industry Canada Statement (for Canadian Customers)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
1.4 Bluetooth
This unit contains a Class 2 Bluetooth transmitter working at 2.4GHz.
Safety Information and Warnings
Moisture
- To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain, moisture, dripping or splashing.
- Do not use this apparatus near water.
Remote Control Batteries
The remote control supplied with this unit contains a battery. To prevent battery leakage which may result in bodily injury, property damage, or damage to the unit:
- Install the battery correctly, + and – as marked on the unit.
- Remove the battery when the unit is not used for a long time.
- Do not expose the battery or remote control to excessive heat, including sunshine.
- CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
- WARNING – DO NOT INGEST BATTERY – CHEMICAL BURN HAZARD.
- If the battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you Zthink batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention
Disposal of Batteries
The battery supplied contains perchlorate material and in many areas batteries
may not be disposed of with your household waste.
Please ensure you dispose of batteries according to local regulations.
The battery supplied does not contain the heavy metals mercury or cadmium.
Servicing
Servicing is required when the unit or mains cord has been damaged in any way,
liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, it does not operate normally,
or has been dropped.
Refer all servicing to qualified service personnel.
Symbols used on this product
| High Voltage Hazard Symbol| This symbol indicates uninsulated material
within your unit may cause an electrical shock. For the safety of everyone in
your household, please do not remove the product covering.
---|---|---
| Hazard Warning Symbol| The ‘exclamation mark’ calls attention to features
for which you should read this manual closely to prevent operation and
maintenance problems.
WARNING: To reduce the risk of fire or electric shock, this apparatus should
not exposed to rain or moisture and object filled with liquids, such as
vases, should not be placed on this apparatus.
CAUTION: To prevent electric shock, match wide blade of plug to wide slot,
fully insert.
****| Waste Electrical and Electronic Equipment Symbol| This symbol
indicates that when the unit is to be discarded, it must be separated from
other household-type waste and sent to separate collection facilities for
recovery and recycling of electrical and electronic equipment.
Please make sure you are familiar with your local rules on the separate
collection of electrical and electronic products.
Introduction
Q Acoustics E120 is an installed DAB, FM, Bluetooth and AUX input Hi-Fi system
easily installed into your room. It is particularly suited to kitchens,
bathrooms and bedrooms but could equally be used in any other room in the
house.
The following instructions assume that you are competent in general electrical
installation skills. You will need to mount a touch panel into a double gang
back box and route cables from this box to the speakers and mains. If you are
not confident in doing this you should seek professional assistance from a
qualified electrician.
It is possible to connect TV sound or another device into the rear auxiliary
line input using an additional cable.
The main E120 wall unit is IP54 rated. It should be located outside zone 2 of the electrical safety zones, if in doubt you are advised to seek assistance from a qualified electrician.
Package contents
1st Fix Package contents:
Main unit contents:
1 x In-wall audio system keypad| 1 x Wall unit mounting frame + 2 x M3.5mm x40mm screws| 1 x 1.0mm wall gasket + 2.5mm wall gasket
Power supply contents:
Additional contents:
1 x Waterproof remote control + cell battery| 1 x Premium remote control + 2 x AAA batteries| 1 x User guide + installation guide
Optional parts (purchased separately or part of a pack):
Q Acoustics QI65C in-ceiling speakers| Optical or analogue audio cable
E120 System Schematic
The system is designed to be connected together as shown below:
Key:
| Power cable
---|---
| Speaker cable (left)
| Speaker cable (right)
| 3.5mm jack cable (not supplied)
| Optical mini TOSLINK (not supplied)
| Antenna cable
Planning E120 positioning and back box locations
Use the guidelines below to plan the positioning of the back boxes, speakers,
and cabling. Dimensions should be checked prior to installation to ensure the
layout works correctly with the supplied lengths of cable.
If more than 7m of speaker cable is required then a suitable alternative such
as QED 16/2 can be purchased and cut to length.
First fix basic wiring
A basic E120 system with auxiliary optical digital input will have the first
fix cable requirement as shown below.
Cut holes for required back boxes and speakers. Run speaker and power cables
as shown, leaving the length of tails accessible for second fix. Optional line
input cable can be run at this point.
Notes:
- Switched mains socket required next to the DC extension cable for the power supply to plug in.
- Single gang back box can be used for the optical AUX input cable. The can be terminated using an optical termination plate such as the Nexia Digital Optical Module Insert.
- The supplied antenna cable can be attached to a normal quality coax cable which then connects to an external antenna. If an external antenna can not be fitted then place the supplied internal antenna as recommended in the Antenna alignment section.
Key:
| Power cable
---|---
| Speaker cable (left)
| Speaker cable (right)
| Optical mini TOSLINK (not supplied)
| Antenna cable
First fix for line output
The analogue 3.5mm stereo line output can be used to connect an external
amplifier or sub-woofer.
Note that analogue audio signals are prone to picking up interference and
this line output should be limited to 10m.
Bathroom installation guide
E120 can be fitted into a bathroom environment, which is different to most
other rooms in the home. The nature of this wet environment is recognized by
the respective standards authorities who test products in terms of their
suitability to be installed in such areas.
E120 compiles with IP54 (Ingress protection).
E120 system is defined as an ‘Extra Low Voltage Installation’, but the wiring
needs to be installed in accordance with ‘Part P’ of the Design and
Installation of Electrical Installations. If in doubt, you are advised to
seek assistance from a qualified electrician.
Please refer to the diagram below, E120 should be installed in either zone 2
(light blue) or zone 3 (white).
Reaching IP54:
E120 is supplied with two rubber gaskets of different thicknesses which should
be stuck to the wall side of the metal frame prior to screwing the frame to
the back box. This will create a seal between the frame and the wall and
ensure better water protection. If the wall is flat then the thinner 1mm
gasket can be used, for uneven walls (such as between tile joins) then the
thicker 2.5mm gasket can be used.
Wiring for two pairs of speakers
For larger open plan areas, two pairs of speakers can be used to achieve an
even distribution of sound.
A speaker wire (purchased separately) should be fitted between the first
speaker and the second, for both left and right as shown in the diagram. The
speakers should be connected in series where the negative (black) connector
of the first speaker is connected to the positive (red) connector of the
second. The negative (black) connector of the second speaker is then
connected to the negative (black) cable to the E120 unit using a connector
block, as shown in the diagram. This series method of connecting two speakers
will ensure a high quality and reliable sound performance of the speakers.
Second fix
Antenna alignment:
An external DAB antenna is recommended, if that is not possible then E120 is
supplied with a flexible indoor antenna which should be aligned vertically as
shown below.
Configurable Switches:
There are two small switches mounted on the lower PCB that adjust the audio
mode outputs. After making a switch position change you will need to power
down the E120.
SWITCH 1 OFF – Line output is variable, adjusts with amplifier volume.
SWITCH 1 ON – Line output is fixed at 100%
SWIITCH 2 OFF – Amplifier speaker outputs are in stereo mode with separate
left and right channels.
SWITCH 2 ON – Amplifier speaker outputs are in mono mode with both left and
right channels combined on both speaker outputs.
Connect cable tails to wall panel, speaker and power supply. Fix items in place using instructions supplied with the speakers to ensure correct speaker installation.
Notes:
- Blanking plate required to cover break out box, requires a single hole to exit DC extension cable.
- Optional AUX input / TV sound requires a 25 x 50mm TOSLINK optical socket module (if using optical cable), such as the ‘Nexia Digital Optical Module Insert’ which is a 25x50mm slot in Module.
Removing the E120 wall panel
To remove the wall panel once it has been ‘clicked’ into the mounting frame
follow these steps:
- Remove the small rubber grommets from each of the small holes around the outer frame, keep safe.
- Use the small removal tool provided, or a similar tool 1.4mm diameter to insert into the hole, add a little pressure into the frame whilst gently pulling the corresponding corner of the wall unit away from the wall.
- When the unit comes away slightly, repeat the process for the next hole until all four have been released.
- The E120 wall unit can now be removed away from the mounting frame and off the wall.
Specification
| Audio Sources | DAB/ DAB+ / FM with RDS | F-connector |
|---|---|---|
| Bluetooth | Wireless | BT 5.0 A2DP |
AUX:
– Analogue| 3.5mm stereo Sensitivity: 350mV
Max level: 1.5V
Impedance: 10k ohm
– Optical| mini TOSLINK Resolution: 16bit 48kHz
Audio Outputs| Speaker outputs| Left & Right Stereo or dual mono
Analogue line| 3.5mm stereo Modes: Fixed or variable Max level: 670mV
Amplifier| Class D| Continuous power 2 x 25W @ 6ohm
THD 0.07% @ 1W 0.2% @ rated power
SNR >75dB @ Rated power
Frequency response 20Hz – 20kHz +/- 1dB
Ratings| | E120 wall panel IP54
Splash proof remote IP54
Control| Touch sensitive buttons x 15
IR remote control x 13
BT AVRCP v1.6 (play, pause, skip, track, artist, album name)
Menu languages English, German, Dutch, French, Danish, Spanish Italian,
Norwegian, Polish, Finnish
Alarms x2 once, daily, weekdays, weekends
General
Cables| Power supply| Input 100 – 240VAC 50/60 Hz
Output 22V DC 1.5amps
Dimensions (HxWxD) 30mm x 50mm x 115mm
Power consumption| Typical 10W
Standby <1W
Deep standby <0.5W
Wall panel| Net weight 0.251kg
Dimensions (HxWxD) 91mm x 151mm x 33mm
Operating ambient temperature Max. 40 °C
Speaker cable| Gauge 19 AWG
Lengths 2 x 7m
DC extension| Gauge 16 AWG
Lengths 5m
Connectors| 5.5mm x 2.5mm DC male
| 5.5mm x 2.5mm DC female
Warranty
Q Acoustics Media products are warranted free of defects in materials and
workmanship for a period of 1 year from the date of purchase. During the
warranty period Q Acoustics will, at its option, repair or replace any
product found to be faulty after inspection by the company or its appointed
distributor or agent.
Misuse and fair wear and tear are not covered by warranty.
Goods for repair should in the first instance be returned to the supplying
dealer. If this is not possible contact Q Acoustics or their appointed
distributor for your area to determine the correct warranty procedure. If
possible the original packaging should be used to return the product as damage
sustained during transit to the repair centre is not covered by the warranty.
The warranty does not in any way affect your legal rights.
Warranty can be extended to 2 years by registering your product at
www.qacoustics.co.uk/register.
For service information in other countries visit:
www.qacoustics.co.uk
Q Acoustics
Armor Home Electronics Limited
Woodside 2, Dunmow Road
Bishops Stratford, Hertz
CM23 5RG
Our policy is one of continuous product improvement.
We reserve the right to change the designs and specifications without notice.
This document contains information that is subject to change without notice.
The Bluetooth® word mark and logo are registered trademarks owned by Bluetooth
SIG, Inc. and use of such marks by Armour Home Electronics Limited is under
license. Other trademarks and trade names are those of their respective
owners.
QACOUSTICS.CO.UK
Q17783-IS-EN_r2
Documents / Resources
| Q
ACOUSTICS E120 In Wall HiFi
Amplifier
[pdf] Installation Guide
E120 In Wall HiFi Amplifier, E120, In Wall HiFi Amplifier, Wall HiFi
Amplifier, HiFi Amplifier, Amplifier
---|---
References
- Background Music Systems & Home Audio Specialists | Audio Volt
- Q Acoustics: Beautifully Engineered Speakers and Soundbars
- Warranty
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>