TUFFSTUFF AP-71LE Leg Extension Owner’s Manual
- June 10, 2024
- TUFFSTUFF
Table of Contents
AMERICA’S PREMIER EXERCISE EQUIPMENT
AP-71LE Leg Extension
Owner’s Manual
Introduction
About the LEG EXT/CURL STATION. Congratulations on your new purchase of the
LEG EXT/CURL STATION. We hope you are completely satisfied with this product
and wish you many years of enjoyment.
Tuff Stuff Equipment
This Tuffstuff product has been built to precise quality standards and has
been carefully packaged to ensure that damage will not occur during shipment.
The Home Lifetime Warranty and signature indicating final inspection has been
conducted by our line foreman, is an expression of our confidence in the
completeness, the materials, and workmanship of this product.
Warranty
SEE A COPY OF WARRANTY ON BACK PAGE.
Registration Card
To avoid unnecessary delays in warranty service and to insure that a permanent
record of your purchase is on file with our factory, be sure to complete the
warranty registration card and send it to TuffStuff Fitness Equipment today.
Specifications
- Maximum Wt. Capacity – 200 lbs.
- Total Machine Weight – 434 lbs.
- Footprint (LWH) – Height is 77”. For footprints refer to the Center Post/Rear Post Assembly Manuals.
Note: Due to continuing product improvements, specifications and designs
are subject to change without notice.
Prior to the Assembly of the LEG EXT/CURL STATION
- We advise you to consult your local Tuff Stuff retailer if you should have a question or problem regarding the proper assembly of this unit.
Tool Requirements
- One 7/8” combination wrench
- Two 3/4” combination wrench
- One 9/16” combination wrench
- One 1/2” combination wrench
- One 7/16” combination wrench
- One adjustable wrench
- One ratchet
- One 3/4” socket
- One 9/16” socket
- One rubber mallet
- Windex or household glass cleaner
- Measuring tape
- Utility knife
- The hex key alloy set included in the Center Post/Rear Post box.
Safety Precautions
Safety First
Regardless of how enthusiastic you may be about getting on your equipment
and exercising, take the time to ensure that your safety is not jeopardized. A
moment’s lack of attention can result in an accident, as can failure to
observe certain simple safety precautions.
-
Read, study and understand the Assembly Instructions and all the warning labels on this product. Furthermore, it is recommended to familiarize yourself and others with the proper operation and workout recommendations for this Tuff Stuff product prior to use.
-
It is imperative that you retain this Assembly Instructions and be sure all warning labels are legible and intact. Replacement Assembly Instructions and labels are available from your local Tuff Stuff retailer.
-
Consult with your physician before beginning any exercise program.
-
Frayed or worn cables can be dangerous and may cause injury.
Periodically check the cable for any indication of wear. -
Use proper discretion when children are present.
-
Keep hands, limbs, loose clothing and long hair well out of the way of moving parts.
-
Do not attempt to lift more weight than you can control safely.
-
Inspect the Unit for any sign of wear on parts, hardware becoming loose or cracks on welds. If a problem is found do not use or allow the machine to be used until the defective part is repaired or replaced.
IMPORTANT ASSEMBLY INSTRUCTION NOTE
INSTRUCTIONS FOR A SINGLE STATION ASSEMBLY ONLY: FOR STEPS 1 AND 2 YOU WILL
NEED SOME HARDWARE THAT IS PROVIDED IN THE AP-70RP BOX. ONCE YOU COMPLETE
STEPS 1 AND 2 SKIP TO STEP 5 TO RESUME INSTALLATION.
INSTRUCTIONS FOR A MULTI STATION ASSEMBLY ONLY: BEGIN ASSEMBLY IN STEP 3. FOR
STEPS 3 AND 4 YOU WILL NEED SOME HARWARE THAT IS PROVIDED IN THE AP-70CP BOX.
STEP 1
Assembly List
Item #| Description| Qty.
B1| REAR POST| 1
B7| FLAT WASHER SAE N/P 3/8”| 4
B8| FLAT WASHER N/P 3/8 ID X 1 1/2 OD X 3/16| 4
B9| NYLON INSERT LOCK NUT N/P 3/8-16| 4
B11| SOCKET CAP SCREW GR-8 N/P 3/8-16 X 3| 4
6| BASE FRAME| 1
17| SEAT FRAME| 1
44| BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 5| 2
53| FLAT WASHER SAE N/P 3/8”| 2
60| NYLON INSERT LOCK NUT N/P 3/8-16| 2
83| U-SHAPE WASHER N/P 3/8 ID X 1 1/2 OD X 3/16| 2
STEP 2
Assembly List
Item #| Description| Qty.
B7| FLAT WASHER SAE N/P 3/8”| 4
B8| FLAT WASHER N/P 3/8 ID X 1 1/2 OD X 3/16| 4
B9| NYLON INSERT LOCK NUT N/P 3/8-16| 4
B11| SOCKET CAP SCREW GR-8 N/P 3/8-16 X 3| 4
11| GUIDE RODS 3/4 RD X 71 3/4| 2
21| SPACER 1 ID X 1 1/4 OD X 2| 2
23| TOP GUIDE ROD HOUSING| 1
25| SELECTOR PIN W/COIL 3/8 X 4 GOLD KNOB| 1
27| 10 LB TOP PLATE W/ADJ SLTR BAR 19 BLK WTS| 1
44| BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 5| 1
50| DECAL-WEIGHT NUMBERS REF TP-10 (200 lbs)| 1
55| FLAT WASHER N/P 3/4 X 2| 4
60| NYLON INSERT LOCK NUT N/P 3/8-16| 1
68| RUBBER DONUT 3/4 X 2 1/2| 2
88| 10 LB STEEL WEIGHT PLATE BLACK 4 9/16 X 9 7/16| 19
STEP 3
Assembly List
Item #| Description| Qty.
A1| CENTER POST| 1
A7| SOCKET CAP SCREW GR-8 N/P 3/8-16 X 1| 4
A8| FLAT WASHER SAE N/P 3/8”| 4
A10| SPLIT LOCK WASHER N/P 3/8”| 4
6| BASE FRAME| 1
17| SEAT FRAME| 1
44| BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 5| 2
53| FLAT WASHER SAE N/P 3/8”| 2
60| NYLON INSERT LOCK NUT N/P 3/8-16| 2
83| U-SHAPE WASHER N/P 3/8 ID X 1 1/2 OD X 3/16| 2
STEP 4
Assembly List
Item #| Description| Qty.
A7| SOCKET CAP SCREW GR-8 N/P 3/8-16 X 1| 4
A8| FLAT WASHER SAE N/P 3/8”| 4
A10| SPLIT LOCK WASHER N/P 3/8”| 4
11| GUIDE RODS 3/4 RD X 71 3/4| 2
21| SPACER 1 ID X 1 1/4 OD X 2| 2
23| TOP GUIDE ROD HOUSING| 1
25| SELECTOR PIN W/COIL 3/8 X 4 GOLD KNOB| 1
27| 10 LB TOP PLATE W/ADJ SLTR BAR 19 BLK WTS| 1
44| BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 5| 1
50| DECAL-WEIGHT NUMBERS REF TP-10 (200 lbs)| 1
55| FLAT WASHER N/P 3/4 X 2| 4
60| NYLON INSERT LOCK NUT N/P 3/8-16| 1
68| RUBBER DONUT 3/4 X 2 1/2| 2
88| 10 LB STEEL WEIGHT PLATE BLACK 4 9/16 X 9 7/16| 19
STEP 5
Assembly List
Item #| Description| Qty.
8| CROSS BRACE| 1
9| DOUBLE PULLEY BRACKET (4 1/2 PULLEYS)| 2
12| HANDLES| 1
20| SIDE FRAME| 1
26| REINFORCEMENT PLATE 1/4 X 2 X 5 (3/8-16 TPI HLS)| 1
38| BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 1| 2
41| BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 2| 2
43| BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 3| 2
53| FLAT WASHER SAE N/P 3/8”| 10
57| BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 2 3/4| 2
56| FLAT WASHER N/P 3/8 ID X 1 1/2 OD X 3/16| 2
60| NYLON INSERT LOCK NUT N/P 3/8-16| 4
61| NYLON PULLEY 3/8 X 1 X 4 1/2 BLACK| 2
74| SOCKET CAP SCREW GR-8 N/P 3/8-16 X 3| 2
79| SPLIT LOCK WASHER N/P 3/8”| 6
83| U-SHAPE WASHER N/P 3/8 ID X 1 1/2 OD X 3/16| 2
STEP 6
Assembly List
Item #| Description| Qty.
13| LEG HOLDOWN| 1
22| SWIVEL FOOT ROLL TUBE| 1
38| BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 1| 2
56| FLAT WASHER N/P 3/8 ID X 1 1/2 OD X 3/16| 2
79| SPLIT LOCK WASHER N/P 3/8”| 2
STEP 7
LEG EXT/CURL CABLE ASSEMBLY
Assembly List
Item #| Description| Qty.
7| CABLE| 1
33| BLACK NYLON PULLEY 3/8 X 1 1/2 X 4 1/2| 1
36| BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 2 1/4| 1
40| BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 1 3/4| 2
51| FINISHED HEX NUT N/P 1/2-13| 1
53| FLAT WASHER SAE N/P 3/8”| 4
59| SHOULDER BOLT N/P 3/8 X 1 1/8| 1
60| NYLON INSERT LOCK NUT N/P 3/8-16| 2
61| NYLON PULLEY 3/8 X 1 X 4 1/2 BLACK| 1
66| ROD END 1/2-13 (3/8 HOLE)| 1
76| SPLIT BOLT GR-8 N/P 1/2-13 X 1| 1
77| SPLIT HEX TAP BOLT GR-8 N/P 1/2-13 X 3 1/2| 1
78| SPLIT LOCK WASHER N/P 1/2”| 2
86| BLACK NYLON PULLEY 3/8 X 1 X 3 1/2| 1
89| NYLON INSERT LOCK NUT N/P 5/16-18| 1
STEP 8
Assembly List
Item #| Description| Qty.
24| WEIGHT SHIELD| 2
37| BUTTON HEAD SCREW GR-8 N/P 1/4-20 X 3/4| 4
54| FLAT WASHER USS N/P 1/4”| 4
85| WEIGHT STACK LID| 1
STEP
9
Assembly List
Item #| Description| Qty.
10| FOAM ROLL 2 X 5 1/2 X 19 3/4| 2
39| BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 1 1/4| 2
58| ALUMINUM WASHER 3/8 X 2.584 OD X .15 THK.| 1
72| RUBBER HANDLE| 1
79| SPLIT LOCK WASHER N/P 3/8”| 2
STEP 10
Assembly List
Item #| Description| Qty.
4| BACK PAD| 1
8| SEAT PAD| 1
39| BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 1 1/4| 4
53| FLAT WASHER SAE N/P 3/8”| 4
COLOR CHART
GRAY= SUB-ASSEMBLY PARTS
BLACK= HARDWARE
AP-71LE
Parts List
Item No.| Description| Rev.| Part No.| Qty.| Item
No.| Description| Part No.| Qty.
---|---|---|---|---|---|---|---|---
1| ACTUATOR ARM| 0| UP6213| 1| 47| DECAL‐IMPORTANT ADJUST CABLE HERE (REV 0)|
BNH1893| 1
2| ADJUSTABLE CAM| 1| UP6214| 1| 48| DECAL‐IMPORTANT FOR BEST PERFORMANCE…
(REV 0)| BNH1894| 2
3| ADJUSTABLE RELEASE HANDLE| 0| UP7086| 1| 49| TUFFSTUFF LOGO ALUMINUM SMALL
(ADHESIVE)| BNH2463| 1
4| BACK PAD| 0| UP6147| 1| 50| DECAL‐WEIGHT NUMBERS REF TP‐10 (200 lbs)|
BNH1542| 1
5| BACK PAD SELECTOR TUBE| 0| UP6137| 1| 51| FINISHED HEX NUT N/P 1/2‐13|
BNH2516| 1
6| BASE FRAME| 0| UP6215| 1| 52| FLAT HEAD SOCKET CAP SCREW N/P 3/8‐16 X 1
1/4| BNH2459| 2
7| LEG EXT/CURL CABLE| 0| UP6216| 1| 53| FLAT WASHER SAE N/P 3/8ʺ| BNH2524| 26
8| CROSS BRACE| 0| UP6217| 1| 54| FLAT WASHER USS N/P 1/4ʺ| BNH2525| 4
9| DOUBLE PULLEY BRACKET (4 1/2 PULLEYS)| 0| UP6225| 2| 55| FLAT WASHER N/P
3/4 X 2| BNH2526| 4
10| FOAM ROLL 2 X 5 1/2 X 19 3/4| 0| UP7084| 2| 56| FLAT WASHER N/P 3/8 ID X 1
1/2 OD X 3/16 THICK| BNH2396| 5
11| GUIDE RODS 3/4 RD X 71 3/4| 0| UP6201| 2| 57| BUTTON HEAD SOCKET CAP SCREW
GR‐8 N/P 3/8‐16 X 2 3/4| BNH2436| 2
12| HANDLES| 0| UP6252| 1| 58| ALUMINUM WASHER 3/8 X 2.584 OD X .15 THK.|
BNH1521| 1
13| LEG HOLDOWN| 0| UP6218| 1| 59| SHOULDER BOLT N/P 3/8 X 1 1/8| BNH2498| 1
14| PIVOT ARM| 0| UP6219| 1| 60| NYLON INSERT LOCK NUT N/P 3/8‐16| BNH2450| 13
15| RELEASE HANDLE| 0| UP6220| 1| 61| NYLON PULLEY 3/8 X 1 X 4 1/2 BLACK|
BNH0506| 3
16| RELEASE HANDLE HOUSING| 0| UP6221| 1| 62| PLASTIC INSERT ELLIPTICAL GUIDE
(2X4)| BNH1760| 1
17| SEAT FRAME| 0| UP6222| 1| 63| PULL PIN STIFF SPRING 17/32 X 1 1/2 K‐105SS|
BNH0519| 1
18| SEAT PAD| 0| UP6253| 1| 64| PUSH PULL PIN 1/2 X 5 5/8 ASSY W/BALL KNOB|
BNH2471| 1
19| SELECTOR PLATE| 0| UP6226| 1| 65| PUSH PULL PIN ASSY 3/8 X 2 1/2 DRILLED|
BNH1429| 1
20| SIDE FRAME| 0| UP6224| 1| 66| ROD END 1/2‐13 (3/8 HOLE)| BNH2488| 1
21| SPACER 1 ID X 1 1/4 OD X 2| 0| UP6267| 2| 67| ROLL PIN N/P 3/8 X 1 1/2|
BNH2531| 1
22| SWIVEL FOOT ROLL TUBE| 0| UP6250| 1| 68| RUBBER DONUT 3/4 X 2 1/2|
BNH0068| 2
23| TOP GUIDE ROD HOUSING| 0| UP6248| 1| 69| RUBBER FOOT FOR 6 X 4 1/4 PLATE|
BNH1647| 3
24| WEIGHT SHIELD| 0| UP6205| 2| 70| RUBBER GRIP 1 ID X .125 X 7| BNH0962| 2
25| SELECTOR PIN W/COIL 3/8 X 4 GOLD KNOB| 0| UP3035| 1| 71| RUBBER GROMMET
3/4ʺ ID| BNH0401| 2
26| REINFORCEMENT PLATE 1/4 X 2 X 5 (3/8‐16 TPI HLS)| 0| UP7085| 1| 72| RUBBER
HANDLE| BNH2122| 1
27| 10 LB TOP PLATE W/ADJ SLTR BAR 19 BLK WTS ASSY| BNH1982| 1| 73| SHOULDER
BOLT N/P 3/8 X 3/4| BNH2392| 1
28| ALUMINUM CAP 1.020ʺ RD (CAP‐100)| BNH0537| 2| 74| SOCKET CAP SCREW GR‐8
N/P 3/8‐16 X 3| BNH2369| 2
29| ALUMINUM FOOT ROLL CAP 2 3/8 ID X 4 1/2 OD X 3/4| BNH1510| 4| 75| SOCKET
SET SCREW N/P 10‐32 X 1/8| BNH2518| 14
30| ALUMINUM INSERT CAP 2ʺ RD| BNH2470| 4| 76| SPLIT BOLT GR‐8 N/P 1/2‐13 X 1
(RND CUT)| BNH2478| 1
31| ALUMINUM INSERT ELLIPTICAL CAP 2 X 4| BNH2398| 2| 77| SPLIT HEX TAP BOLT
GR‐8 N/P 1/2‐13 X 3 1/2| BNH2527| 1
32| BALL BEARING #W 516| BNH0628| 2| 78| SPLIT LOCK WASHER N/P 1/2ʺ| BNH2519|
2
33| BLACK NYLON PULLEY 3/8 X 1 1/2 X 4 1/2 (V3700)| BNH1694| 1| 79| SPLIT LOCK
WASHER N/P 3/8ʺ| BNH2520| 11
34| BLACK RUBBER GRIP 1/2 X 4 1/2| BNH2015| 1| 80| SUPER LUBE TEFLON LUBRICANT
82340| BNH0704| 1
35| BRONZE BUSHING 1 X 1 1/4 X 3/4 X 1 1/2 X 1/8| BNH0527| 6| 81| RUBBER
BUMPER 2ʺ| BNH2486| 2
36| BUTTON HEAD SOCKET CAP SCREW GR‐8 N/P 3/8‐16 X 2 1/4| BNH2429| 1| 82|
URETHANE BUMPER 962| BNH0244| 2
37| BUTTON HEAD SOCKET CAP SCREW GR‐8 N/P 1/4‐20 X 3/4| BNH2447| 4| 83|
U‐SHAPE WASHER N/P 3/8 ID X 1 1/2 OD X 3/16 THICK| BNH2393| 4
38| BUTTON HEAD SOCKET CAP SCREW GR‐8 N/P 3/8‐16 X 1| BNH2528| 6| 84| U‐STYLE
TAPPED HOLE NUT 1/4‐20| BNH0708| 4
39| BUTTON HEAD SOCKET CAP SCREW GR‐8 N/P 3/8‐16 X 1 1/4| BNH2521| 6| 85|
WEIGHT STACK LID| BNH1693| 1
40| BUTTON HEAD SOCKET CAP SCREW GR‐8 N/P 3/8‐16 X 1 3/4| BNH2426| 2| 86|
BLACK NYLON PULLEY 3/8 X 1 X 3 1/2 (P‐35375‐H)| BNH0553| 1
41| BUTTON HEAD SOCKET CAP SCREW GR‐8 N/P 3/8‐16 X 2| BNH2427| 2| 87|
DECAL‐WARNING ATTENTION USERS! MAKE… (REV 0)| BNH2152| 1
42| BUTTON HEAD SOCKET CAP SCREW GR‐8 N/P 3/8‐16 X 2 1/2| BNH2428| 1| 88| 10
LB STEEL WEIGHT PLATE BLACK 4 9/16 X 9 7/16 ASSY| BNH1650| 19
43| BUTTON HEAD SOCKET CAP SCREW GR‐8 N/P 3/8‐16 X 3| BNH2432| 2| 89| NYLON
INSERT LOCK NUT N/P 5/16‐18| BNH2529| 1
44| BUTTON HEAD SOCKET CAP SCREW GR‐8 N/P 3/8‐16 X 5| BNH2440| 3| 90| DECAL
WARNING PINCH POINTS 2 X 1.5| BNH2497| 1
45| DECAL‐DANGER TIGHTEN THIS RETAINING… (REV 2)| BNH0142| 2| 91| DECAL‐
SERIAL NO. (AP‐71LE)| BNH2538| 1
46| DECAL‐EXERCISE LEG EXTENSION/CURL| BNH2465| 1| | | |
Maintenance
TuffStuff Basic Strength Equipment Safety and General Maintenance
All TUFFSTUFF strength equipment is designed and manufactured to offer
maximum, long-life service with minimal maintenance. However, safety
inspection and routine maintenance in your facility should be the upmost
importance in your daily operation. Information presented in these pages will
serve as a basic guideline to design your own inspection procedures.
Part One: General Inspection and Cleaning
Equipment should be wiped down with a damp cloth and dried on a daily basis.
The powder coat finish should be polished with a good car wax on a monthly
basis. A daily wipe down of the upholstery with a lanolin based hand cleaner
or Naugahyde Cleaner. Do not use cleaners such as Lysol or Windex as they will
dry out and crack the vinyl. Lanolin hand cleaner dissolves the sweat and
lubricates the vinyl, maintaining its natural flexibility. Sweat is corrosive
and when left on the frame and components will eventually cause corrosion or
rust. When performing these cleaning sessions, it is the perfect time to
inspect the equipment and note any problems for the maintenance personnel to
correct.
- Check equipment if it is operating properly.
- Check the cable for loose fittings or frayed cable and is seating properly on the pulleys and cams.
- Make sure that the proper weight stack selector pin is with each machine and that the pin functions properly.
- If something appears loose be sure to have it tightened immediately.
- If a piece of equipment appears damaged or not operation properly, place the piece out-of-service immediately.
Part Two: Maintenance
In this paragraph, we will discuss the inspection of the cables, pulleys and
their associated components. If there exists the potential for injury to occur
on a machine, it will most likely lie in the cable system. It is important to
inspect the cables frequently and let it be known to all users that it is
their responsibility to report any worn-out cable to prevent a sudden failure
that can result in an injury. Cables are moving parts, meaning cable-wear will
occur regardless of the type or size used. In the advent of the 3/16” mill-
spec cable this wear takes longer to become apparent and this is why frequent
inspections are so important.
- Check the cable termination at the weight stack. To perform any cable tension adjustment, loosen the hex jam nut and thread the hex tap bolt in or out to give cable the proper tension. Re-tightened the hex jam nut when adjustment is complete and make sure the hex tap bolt is threaded 1/2” into the socket of the selector bar top plate.
- Check the cable as it terminates at the cam. Check the end fitting for any signs of fraying in this area. Inspect the bolt and nut and/or screw holding the fitting and be sure that it is tight.
- Check the cables as it passes over all pulley wheels. Visually inspect the cables and pulleys. A cable that is wearing will exhibit a ballooned surface that passes over the pulley. This is and early warning sign to replace the cable.
Part Three: Lubrication
Bearing and linear bearings systems have advanced over the years but they must
be maintained on a regular basis if you expect them to last and perform
efficiently. TuffStuff uses only the highest quality bearings and linear
motion components that are virtually trouble-free but requires the regular
preventive maintenance to insure long-lasting performance.
- Bronze and nylon bushings, we recommend on a monthly basis to spray a teflon-base lubricant (silicone-free) directly onto the shaft as it passes through these bushings. Spray a small amount onto the shaft and rotate it through its complete movement and wipe off any excess.
- Weight stack guide rods and bushings, again use teflon spray lubricant and this time spray onto a rag and wipe the guide rods down with this rag on a weekly basis. Do not use WD-40 or other lubricants as they attract dirt and will crate a mess between the weight plates and bushings.
- Sealed bearings pivot points, as the name implies are protected from the outside environment and require no lubrication. During the machine wipe down, wipe the external bearing surfaces with the damp rag and dried to prevent the build up of dust and sweat.
- Linear bearing systems are precision, high load components that require regular maintenance. Dirt and corrosion are the major culprits in linear bearing failure. The hardened shafts must be wiped down weekly and lubricated with a light layer of teflon grease. We recommend a teflonbase (silicone-free) gel/grease for this purpose. Lack of care and maintenance will result in corrosion of the linear shaft causing the bearings to clogged and jammed.
If you religiously perform the maintenance procedures, you will increase the
life of the machine and ultimately lower your maintenance costs with fewer
replaced components and downtime.
Any doubts, equipment with mechanical problems should be placed “Out-of-
Service” until all problems are corrected. If replacement parts are required
or maintenance questions, please contact:
TuffStuff Fitness Equipment, Inc.
Service Department
1325 E. Franklin Avenue
Pomona, CA 91766
1-800-961-9377
e-mail: service@tuffstuff.net
DO NOT DISCARD THIS MANUAL
TUFFSTUFF LIMITED WARRANTY
TuffStuff warrants to the original purchaser that TuffStuff equipment will be
free from defects in material and workmanship. All warranty periods begin to
run from the date of delivery to the original purchaser. The warranty and
remedies set forth herein are conditioned upon proper storage, installation,
use and maintenance and conformance with any recommendations of TuffStuff.
This warranty does not cover products not manufactured by TuffStuff or
products which are altered without the express written consent of TuffStuff.
This warranty as specified:
WARRANTY: a) Frames, welds, cams and weight plates — Lifetime, b)
Pivot bearings, pulleys, bushings, gas shocks and guide rods — Five (5) years,
c) Belts, linear bearings and pull-pin components — One (1) year, and
d) Upholstery, cables, finish and rubber grips — Six (6) months, and all
other parts not mentioned elsewhere in this warranty will expire one (1)
year from the date of delivery to the original purchaser. The obligation of
TuffStuff under this warranty is limited to repairing or replacing warranted
defective parts, as TuffStuff may elect, at TuffStuff’s facility in Pomona,
California, without charge to purchaser for either parts or labor. Purchaser
is responsible for installation of repaired or replaced parts, and all
transportation and insurance costs on returned or replaced equipment to and
from TuffStuff’s facility in Pomona.
THE FOREGOING SHALL CONSTITUTE THE SOLE REMEDY OF THE PURCHASER AND THE SOLE
LIABILITY OF TUFFSTUFF WITH REGARD TO WARRANTY. NO IMPLIED STATUTORY WARRANTY
OR IMPLIED STATUTORY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE SHALL APPLY. IN NO EVENT, WHETHER AS A RESULT OF BREACH OF CONTRACT,
WARRANTY, NEGLIGENCE OR OTHERWISE, SHALL TUFFSTUFF BE LIABLE FOR SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF
PROFITS OR REVENUE, LOSS OF USE OF EQUIPMENT, COST OF CAPITAL, COST OF
SUBSTITUTION EQUIPMENT, DOWNTIME COST, OR CLAIMS OF CUSTOMERS OR PURCHASER
FROM SUCH DAMAGE.
This written warranty is the final, complete and exclusive agreement of the
parties with respect to the quality or performance of the equipment and no
action for breach of this written warranty or any implied warranty shall be
commenced more than one (1) year after the accrual of the cause of action. No
modification of this warranty or waiver of its terms shall be binding on
either party unless approved in writing by an authorized representative of the
party. Contact TuffStuff Fitness Equipment, Inc. at 1325 E. Franklin Avenue,
Pomona, California 91766, before returning any defective equipment.
TuffStuff Fitness Equipment, Inc.
1325 E. Franklin Avenue
Pomona, CA 91766, USA
Ph: 909-629-1600
Fax: 909-629-4967
E-mail: service@tuffstuff.net
Net: www.tuffstuff.net LEG EXT/CURL STATION
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>